OPERATING INSTRUCTIONS - 2.2 TT50C / TT100C Laney POWER TO THE MUSIC MODERN ALL TUBE GUITAR COMBO AMPLIFIER w w w. l a n e y. c o .
TT50C/TT100C IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electric products, basic cautions should always be followed, including the following. 1. Read all safety and operating instructions before using this product 2. The product should be powered by a three pin `grounded (or earthed) plug connected to a power socket with a grounded earth outlet. 3. All safety and operating instructions should be retained for future reference 4.
TT50C/TT100C Intended to alert the user to the presence of uninsulated ‘Dangerous Voltage’ within the products enclosure that may be sufficient to constitute a risk of electrical shock to persons. Este simbolo tiene el proposito de alertar al usuario de la presencia de ‘(voltaje) peligroso’ que no tiene aislamiento dentro de la caja del producto que puede tener una magnitud suficiente como para constituir riesgo de corrientazo.
TT50C/TT100C Laney OPERATING INSTRUCTIONS BEFORE SWITCHING ON After unpacking your amplifier check that it is factory fitted with a three pin 'grounded' (or earthed) plug. Before plugging into the power supply ensure you are connecting to a grounded earth outlet. If you should wish to change the factory fitted plug yourself, ensure that the wiring convention applicable to the country where the amplifier is to be used is strictly conformed to.
TT50C/TT100C Laney OPERATING INSTRUCTIONS Dear Player, Thank you very much for purchasing your new Laney product and becoming part of the worldwide Laney family. Each and every Laney unit is designed and built with the utmost attention to care and detail, so I trust yours will give you many years of enjoyment. Laney products have a heritage which stretches back to 1967 when I first began building valve amplifiers in my parent’s garage.
TT50C/TT100C Laney 4 1 OPERATING INSTRUCTIONS 3 10 1 VOLUME BRIGHT 15 17 18 19 20 16 11 2 MASTER DRIVE MODERN 2 9 14 3 MASTER DRIVE MODERN XPAND 1 3 2 21 22 VOLUME 1 23 VOLUME 2 CHANNEL INPUT BASS 13 12 BRIGHT BOOST BRIGHT MIDDLE TREBLE REVERB BASS MIDDLE TREBLE REVERB BASS MIDDLE TIGHT TREBLE MUTE REVERB REVERB DAMPING FX MIX PRESENCE 27 28 AMP TT100 5 6 7 8 5 6 7 8 5 6 7 8 24 25 26 FRONT PANEL CONTROLS INPUT: Single jack input for connecting yo
Laney OPERATING INSTRUCTIONS FRONT PANEL CONTROLS - continued CHANNEL 2 SWITCH: Press in to activate Channel 2, the led will illuminate when active. Channel 2 is designed to be completely flexible giving punchy cleans, smooth blues and hard rock tones. This switch is footswitchable and midi controllable, for more information on midi see the midi section later in the manual. DRIVE: Sets the level of tube preamplifier gain or how dirty your sound is for the drive channel - Channel 2.
Laney OPERATING INSTRUCTIONS FRONT PANEL CONTROLS - continued MASTER: Sets the overall ‘loudness’ of channel 3. It is useful to experiment with the gain and volume controls. If you want a very open, warm and semi overdriven sound try reducing the amount of drive (15) and increasing the master. BRIGHT: Adds edge and picking emphasise to you sound. This control has more effect at lower drive (10) settings.
Laney OPERATING INSTRUCTIONS FRONT PANEL CONTROLS - continued factor in order to get the bass response you’re looking for. It is normal for this control to make a slicking sound when operated. MUTE: This mutes the output section of the amplifier and the line out socket. It does not affect the signal path through the pre-amplifier, so sends to the fx loops and record out are maintained allowing signal levels to be monitored silently and allow silent recording via the record out.
TT50C/TT100C Laney OPERATING INSTRUCTIONS 30 31 41 32 33 34 35 36 40 42 43 44 45 37 38 39 REAR PANEL CONTROLS POWER INLET SOCKET: Connect to your power source. Make sure the specified voltage is correct for your country! POWER FUSE: This is the main safety fuse for the unit. The fuse protects the AC power to the amplifier. USE ONLY THE CORRECT SIZE AND RATING OF FUSE AS SPECIFIED ON THE PANEL.
Laney OPERATING INSTRUCTIONS REAR PANEL CONTROLS - CONTINUED EXTENSION LOUDSPEAKER: This single ¼” (6.3mm) jack socket can be used to connect an 8-16 ohm extension cabinet. When an extension cabinet is used the switch (36) should be moved to the on position. Failing to do so will result in masmatched impedance and will reduce the amplifiers performance and in some cases may cause damage to the amplifier. Remember to switch back to the off position when not using an extension cabinet.
TT50C/TT100C Laney OPERATING INSTRUCTIONS REAR PANEL CONTROLS - MIDI SECTION The advantage of having midi in your guitar amplifier is that it allows your 42 43 44 41 45 amplifier and external devices (like FX controllers) to talk with each other. At last you can press one button to select the amplifier channel, and choice of effects on multiple devices all at once.
Laney OPERATING INSTRUCTIONS REAR PANEL CONTROLS - continued MIDI THRU: Midi thru is a daisy chain buffered output of the midi in information. It is a 7 pin DIN socket supporting phantom power* Connect to the midi in of the next external midi equipped device in the chain if required. MIDI IN: The TT amplifier receives midi information here from external midi devices such as foot controllers or midi sequencers allowing the status of the amplifer to be switched via midi.
Laney OPERATING INSTRUCTIONS MIDI APPLICATIONS NOTE 2: TT AMPLIFIER AND MIDI CONTROLLER In this configuration the TT amplifier is a slave device ,its setting being called up by the midi controller. This midi controller could be a device which purely generates midi information or a multi effects pedal board. To setup the amplifier you need to do the following:1. Select the required patch on your pedal board/midi controller 2. Select the Channel/Volume/Reverb switch setting on your TT amp. 3.
TT50C/TT100C Laney OPERATING INSTRUCTIONS QUICK START SETTINGS - suggestions only! Experiment Crystal Clean Blues Clean Blues Lead Page 15/24
TT50C/TT100C Laney OPERATING INSTRUCTIONS QUICK START SETTINGS - continued Rock Rhythm Rock Lead Metal Page 16 /24
TT50C/TT100C Laney OPERATING INSTRUCTIONS USER SETTINGS - Store your own cool sounds here Page 17/24
TT50C/TT100C Laney OPERATING INSTRUCTIONS TUBE AMPLIFIER SURVIVAL TIPS Tube amplifiers generally sound much warmer/sweeter than solid state transistor amplifiers but they also need a little more respect due to the fragile glass tubes themselves.
TT50C/TT100C Laney OPERATING INSTRUCTIONS TUBE AMPLIFIER SURVIVAL TIPS - continued V6 V8 V5 V3 V7 V8 V7 V6 V4 V2 V5 V3 V1 TT50C Tube Layout TT100C Tube Layout V4 V10 EL34B Grade Number V1 V2 V3 V4 V5 V6 V7-10 V2 V1 V9 ECC83 ECC83 ECC83 ECC83 ECC83 ECC83 EL34B-STR (High Grade) (High Grade) (Standard) (Standard) (Standard) (Standard) 1st Gain Stage Channel 1 1st Gain Stage Channel 2 2nd Gain Stage Channel 2 1st Gain Stage Channel 3 2nd Gain Stage Channel 3 Power Driver Stage Output T
TT50C/TT100C Laney OPERATING INSTRUCTIONS TT SAMPLE SYSTEM 1 Input FX Controller Output General Notes Amplifier connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. BEFORE turning on your guitar amplifier. Many products have large transient surges at turn on and off which can cause damage to your speakers.
TT50C/TT100C Laney OPERATING INSTRUCTIONS TT SAMPLE SYSTEM 2 Midi Out Input FX Controller Output Extension Speaker ‘On’ Laney Power To The Music RB115 TT412A Model Power Rating 300W Program Serial Number: SAMPLE DESIGNED IN THE UK BY LANEY www.laney.co.
TT50C/TT100C Laney OPERATING INSTRUCTIONS BLOCK DIAGRAM RECORD OUT CHANNEL1 EQ FX SEND CHANNEL2 INPUT DRIVE EQ FX RETURN MASTER VOLUME 1 OUTPUT STAGE FX MIX MASTER VOLUME CHANNEL SWITCHING MASTER VOLUME 2 CHANNEL3 DRIVE MUTE VOLUME/ BRIGHT EQ LINE OUT MASTER VOLUME REVERB RETURN PRESENCE MASTER REVERB NOTE: This product conforms to the requirements of the following European Regulations, Directives & Rules:CE Mark (93/68/EEC), Low Voltage (72/23/EEC), EMC (93/68/EEC), RoHS (EU2002/95/EC
VH100R TT50C/TT10 0C Laney OPERATING INSTRUCTIONS SPECIFICATIONS Supply Voltage Mains Fuse TT50C Mains Fuse TT100C HT Fuse Power Consumption Output Power Rating Loudspeaker TT50C Loudspeakers TT100C Extension Loudspeaker socket Features ~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz Factory Option (~220V>240V = T2A L 250V) (~100>120V = T5A L 250V) (~220V>240V = T3.15A L 250V) (~100>120V = T6.
Laney POWER TO THE MUSIC METAL JAZZ BLUES ROCK AMPICONS ARE HERE TO HELP! LANEY AMPLIFICATION w w w. l a n e y. c o . u k In the interest of continued product development, Laney Reserves the right to amend product specification without prior notification.
