2510 Series In-Row Ripper Operator’s Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.
Table of Contents 1 Introduction Understanding Safety Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 2 Standard Specifications 3 Assembly Instructions Assembly Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Jackstand Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii F-729-0913 Edition
Chapter 1 Introduction The Landoll Model 2510 In-Row Ripper is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation CHAPTER 1 gives basic instructions on the use of this manual. CHAPTER 2 gives product specifications. These specifications supply lengths and measures for your equipment.
INTRODUCTION Understanding Safety Statements You will find various types of safety information on the following pages and on the machine signs (decals) attached to the vehicle. This section explains their meaning. The Safety Alert Symbol means ATTENTION! YOUR SAFETY IS INVOLVED! DANGER Danger means a life-threatening situation exists. Death can occur if safety measures or instructions on this label are not properly followed.
Chapter 2 Standard Specifications 2510 SERIES IN-ROW RIPPER SPECIFICATIONS MODEL NO. NO. OF SHANKS 2510-4-30 2510-5-30 2510-6-30 2510-7-30 SHANK SPACING 4 5 6 7 SHANK EXTENSIONS 30” 30” 30” 30” NONE NONE 17” BOLT-ON 27” BOLT-ON TRANSPORT WIDTH 11’-2” 11’-2” 14’-2” 15’-10” ESTIMATED WEIGHT (LBS.) 3,205 3,812 4,610 5,162 TIRE INFLATION TIRE SIZE TIRE MANUFACTURER 20.5 x 8.0-10 PLY/LOAD RATING Load Range D/ 1,320 lb. INFLATION PRESSURE (psi) (max.
STANDARD SPECIFICATIONS 2-2 F-729-0913 Edition
STANDARD SPECIFICATIONS LANDOLL CORPORATION GENERAL TORQUE SPECIFICATIONS (REV. 4/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR GENERAL PURPOSE APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED NUTS AND CAPSCREWS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION). THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.
STANDARD SPECIFICATIONS LANDOLL CORPORATION HYDRAULIC FITTING TORQUE SPECIFICATIONS 37o JIC, ORS, & ORB (REV. 10/97) THIS CHART PROVIDES TIGHTENING TORQUES FOR HYDRAULIC FITTING APPLICATIONS WHEN SPECIAL TORQUES ARE NOT SPECIFIED ON PROCESS OR DRAWING. ASSEMBLY TORQUES APPLY TO PLATED CARBON STEEL AND STAINLESS STEEL FITTINGS ASSEMBLED WITHOUT SUPPLEMENTAL LUBRICATION (AS RECEIVED CONDITION). THEY DO NOT APPLY IF SPECIAL GRAPHITE MOLY-DISULFIDE OR OTHER EXTREME PRESSURE LUBRICANTS ARE USED.
STANDARD SPECIFICATIONS 17 30 36 52 2510-5 shank and lighting placement Figure 2-1: 2510-5-30 Shank and Lighting Placement 2-5
STANDARD SPECIFICATIONS 29-1/2 15 51 79 2510-6 shank and lighting placement Figure 2-2: 2510-6-30 Shank and Lighting Placement 2-6 F-729-0913 Edition
STANDARD SPECIFICATIONS 36 30 46 82-7/16 2510-7 shank and lighting placement Figure 2-3: 2510-7-30 Shank and Lighting Placement 2-7
STANDARD SPECIFICATIONS Page Intentionally Blank 2-8 F-729-0913 Edition
Chapter 3 Assembly Instructions It is very important that your new 2510 Series In-Row Ripper be properly assembled, adjusted, and lubricated before use. Illustrations are provided in this section to show proper assembly procedures. Remove paint from grease fittings and replace any that are damaged or missing. Be sure to return bolts, clips, etc. to their original locations. To insure assemblies are aligned, insert all bolts and leave the nuts loose until completion of final assembly.
ASSEMBLY INSTRUCTIONS SMV EMBLEM SMV MOUNTING BRACKET U-BOLT 5/8-11 HEX LOCK NUT RIGID GAUGE WHEEL ADJUSTMENT PIN 3/16 HAIR PIN OUTER JACK STAND TUBE JACK STAND m2510-parts-id Figure 3-1: 2510 Series Parts Identification 3-2 F-729-0913 Edition
ASSEMBLY INSTRUCTIONS Assembly Preparation SMV Bracket Installation 1. Hook up the In-Row Ripper to a tractor using the three-point hitch. Raise the unit about 36” and place stands under the main frame to prevent accidental lowering. 1. Attach the SMV mounting bracket to the center of the rear frame using u-bolt and 5/8-11 flange head serrated nuts (See Figure 3-1.) WARNING Do not attempt to lift heavy parts (such as the frame), manually. Use a hoist or a forklift to move these parts into position.
ASSEMBLY INSTRUCTIONS 5/8-11 X 3-3/4 HEX HEAD CAP SCREW 3/4-10 X 4 HEX HEAD CAP SCREW SPRING CLAMP ASSEMBLY POINT PIN PLACEMENT CONNEX BUSHING 3/4-10 X 4 HEX HEAD CAP SCREW 3/4-10 HEX LOCK NUT 5/8-11 HEX LOCK NUT WEARSTRIP BRACKET 3/4-10 X HEX LOCK NUT WEARSTRIP 5/8-11 HEX LOCK NUT 3/4-10 X 3 HEX HEAD CAP SCREW 5/8-11 X 3-3/4 HEX HEAD CAP SCREW SHANK POINT ASSEMBLY 5/16 X 2 SPRING SLOTTED PIN SEE DETAIL A m179964 op 1/2 X 2 SPRING SLOTTED PIN DETAIL A Figure 3-2: Auto-Reset Clamp and Shank Asse
ASSEMBLY INSTRUCTIONS 5/8-11 X 5-1/2 HEX HEAD CAP SCREW 3/4-10 X 4 HEX HEAD CAP SCREW RIGID CLAMP ASSEMBLY POINT PIN PLACEMENT CONNEX BUSHING 3/4-10 X 4 HEX HEAD CAP SCREW 3/4-10 HEX LOCK NUT 5/8-11 HEX LOCK NUT 3/4-10 X HEX LOCK NUT WEARSTRIP BRACKET 5/8-11 HEX LOCK NUT WEARSTRIP SHANK POINT ASSEMBLY 3/4-10 X 3 HEX HEAD CAP SCREW 5/8-11 X 5-1/2 HEX HEAD CAP SCREW 1/2 X 2 SPRING SLOTTED PIN 5/16 X 2 SPRING SLOTTED PIN SEE DETAIL A DETAIL A m179965 op Figure 3-3: RSB Clamp and Straight Shank As
ASSEMBLY INSTRUCTIONS FRAME SHANK 3/8 X 2 SPRING SLOTTED PIN CLAMP 1/2-13 X 6 HEX HEAD CAP SCREW 5/8-11 X 1-1/2 SET SCREW 1/2 SPLIT LOCK WASHER 1/2-13 HEX NUT CLAMP PLATE COULTER ASSEMBLY 1/2-13 X 1-1/2 ROUND HEAD SQUARE NECK SCREW 1/2 SPLIT LOCK WASHER COULTER BLADE 5/8-11 X 1-1/2 SET SCREW COULTER STOP WELDMENT m1550-coulter-2 Figure 3-4: Coulter Assembly 3-6 F-729-0913 Edition
ASSEMBLY INSTRUCTIONS Coulter Assembly 1. Assemble coulter shank to coulter assembly using coulter stop weldment and 5/8-11 x 1-1/2 square head set screw. Install 3/8 x 2 spring slotted pins in coulter shank. 2. Install the shank and coulter assembly to the frame with the coulter clamps and plates using 1/2-13 x 6 hex head cap screws and hex lock washers (See Figure 3-4.) 3. Use square head cup point set screws through hole in clamp to hold coulter shank in place. 4.
ASSEMBLY INSTRUCTIONS 19” SELF LOCKING TIE RIGHT LIGHT BRACKET W/ REFLECTORS 1/4-20 HEX LOCK NUT HARNESS STOR-AWAY TAIL LIGHT MOUNT 1/4-20 X 3/4 HEX HEAD CAP SCREW REFLECTOR ASSEMBLY AG AMBER SINGLE LED LAMP STOR-AWAY HOLDER BRACKET 5/8-11 FLANGE HEAD SERRATED NUT 7 PIN/4 PIN HARNESS, 120” 1/4-20 X 1-1/2 HEX HEAD CAP SCREW LED WARNING LIGHT HARNESS 1/4-20 X 1-1/4 HEX HEAD CAP SCREW AG AMBER SINGLE LED LAMP LEFT LIGHT BRACKET W/ REFLECTORS U-BOLT SMV EMBLEM 1/4 FLAT WASHER WARNING LIGHT BAR 1/2-13
ASSEMBLY INSTRUCTIONS 7-PIN 4-PIN CONN TOWER 1 2 3 4 5 6 7 D B A C CIRCUIT 1 WIRE COLOR GROUND WORK LAMPS LEFT FLASHING & TURN STOP LAMPS RIGHT FLASHING & TURN TAIL LAMPS SWITCHED POWER (12V) GROUND BLACK YELLOW RED GREEN BROWN BLUE 7 PIN/4 PIN 120” HARNESS 2 3 4 5 2-PIN 3-PIN 6-PIN 3-PIN 2-PIN TOWER TOWERSHROUDTOWER TOWER BLACK LEFT TURN WHITE GROUND BROWN TAIL YELLOW LEFT TURN GREEN RIGHT RED RIGHT A A C A B A B C B D A B E B C F LED WARNING LIGHT HARNESS m2510 harness wire
ASSEMBLY INSTRUCTIONS Notes: 3-10 F-729-0913 Edition
Chapter 4 Operation and Maintenance DANGER Coulter blades are sharp. Do not allow coulters to roll over or fall on any part of the body. Do not allow wrenches to slip when working near coulter blades. Do not climb over machine above coulter blades. Failure to stay clear of coulter blade edges may result in serious personal injury or death. DANGER Never allow anyone to ride on the In-Row Ripper at any time.
OPERATION AND MAINTENANCE CAT II HITCH CAT III HITCH m2510-hitch Figure 4-1: 3 Point Hitch Setup Tractor Preparation The 2510 Series In-Row Ripper may be used on tractors equipped with category II or III three-point hitches. Before attaching the In-Row Ripper, prepare the tractor as follows: The rear tractor tires should be inflated equally and ballast added according to the tractor operator’s manual. For mounted type models, install front end weights as needed on tractor to maintain stability.
OPERATION AND MAINTENANCE In-Row Ripper Operation 1. Before operating the In-Row Ripper, inspect it to be sure it is in good operating condition. Field Operation — Three-Point Hitch Type 2. Replace badly worn or missing parts. 1. Lower the In-Row Ripper to the ground and pull it a few feet at the approximate desired depth. 3. While the machine is new, bolt tightness should be checked after a few hours of operation. Tighten any loose nuts or cap screws. Check the gauge wheel lug bolts daily. 2.
OPERATION AND MAINTENANCE Wheel Bearing Maintenance 1. Check wheel bearings and coulter bearings occasionally for excessive end play. To correctly replace the wheel bearings: 2. Place the frame on blocks or stands sufficient to lift the tire clear of the ground. Lubrication IMPORTANT Items with grease zerks are listed in the illustrated parts book. 4. Remove the hub. Clean and inspect the bearings and hub cavity. Replace any worn or defective parts. 1.
OPERATION AND MAINTENANCE Notes 4-5
OPERATION AND MAINTENANCE 4-6 F-729-0913 Edition
Chapter 5 Troubleshooting Guide The Troubleshooting Guide, shown below, is included to help you quickly locate problems that can happen using your 2510 Series In-Row Ripper. Follow all safety precautions stated in the previous sections when making any adjustments to your machine. PROBLEM SPIKES DO NOT PENETRATE TO DESIRED DEPTH UNIT BOUNCES OR NOT WORKING AT UNIFORM DEPTH PROBABLE CAUSE Coulters set too deep SOLUTION Adjust coulters up, to just run in firm soil, to cut residue.
TROUBLESHOOTING GUIDE Notes 5-2 F-729-0913 Edition
Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001:2008 registration at all Landoll manufacturing facilities. Model 2510 Series In-Row Ripper Operator’s Manual Re-Order Part Number F-729-0913 LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM Copyright 2010.
