Network Node Data Sheet Publication: 98-1837 Rev AI © Landis+Gyr 2020 | Proprietary + Confidential
Limitation on Warranties and Liability Information in this document is subject to change without notice. This manual or any part of it thereof may not be reproduced in any form unless permitted by contract or by written permission of Landis+Gyr.
Network Node Data Sheet Introduction The Network Node is a fully functional radio that can be deeply integrated into sensor and controller products allowing a wide range of devices to communicate over the RF network. After integration, the product functions as an endpoint on the RF mesh network and will route network traffic, further strengthening the network. There are two models of Network Node the N500 and N550. The N500 operates on RF Mesh networks while the N550 is utilized on RF Mesh IP networks.
Network Node Data Sheet All parameters specified at 25°C unless specified otherwise. Table 1. Network Node Specifications Parameter Condition Target Min Typical Max Units Notes Power Supply Input Voltage Current Consumption 4.0 5.0 VDC Rx mode 70 90 Tx mode (low power) 200 250 Tx mode (medium power) 250 330 Tx mode (high power) 600 750 Processor Type SAM4C Clock Ref 120 MHz RAM (internal) 304 Kbyte Flash (internal) 2 Mbyte Ext.
Network Node Data Sheet Table 1. Network Node Specifications (Continued) Parameter No. of channels (RF Mesh IP) Condition Target Min Typical Max Units Notes Operating mode 50, 150, 200 kbps (400 kHz Channel width) 64 NAM Operating mode 50, 150, 200 kbps (400 kHz Channel width) 11 Hong Kong Transmitter Output power Output power over temperature Adjacent channel power Low power 16 17 18 Med power 21 22 23 High power # 26.5 28 28.
Network Node Data Sheet Table 1. Network Node Specifications (Continued) Parameter Condition Target Min Typical Max Units Notes Environmental Storage Temperature -40 +85 °C Operating Temperature -40 +85 °C Relative Humidity 5 85 % Non-condensing Approved Antennas Landis+Gyr P/N 106119-000 Whip, 5.
Network Node Data Sheet Height Representation: (Unless Otherwise Noted) • Top Side: 0.208” Max • Bottom Side: 0.095” Max Tooling Holes Figure 3. B ottom Side View Unless otherwise specified: Dimensions are in Inches [MM] Dimensions are after finish is applied Angle tolerance does not apply to implied 90 degree angles Tolerance on: Data Sheet • Decimal • Fraction • Agles • 1PL +.1 • + 1/64 • + 1° • 2PL +.2 • • • 3PL +.
Network Node Data Sheet FCC, Industry Canada Compliance, and Regulatory Compliance Brazil FCC Class B This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received, including interference that may cause undesired operation.
Network Node Data Sheet This radio transmitter (5294A-NG0R1S3) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, or having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Approved Antennas: • Landis+Gyr P/N 106119-000 Whip, 5.
Network Node Data Sheet Host FCC Label Requirement In the final installation, the following information must be visible: • Contains FCC ID: R7PNG0R1S3 • Contains IC: 5294A-NG0R1S3 • Model: Network Node N500/N550 This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 8 | 98-1837 Rev AI • This device may not cause harmful interference. • This device must accept any interference received, including interference that may cause undesired operation.
