User Manual
Table Of Contents
- Chapter 1: Product Overview 1
- Chapter 2: Configuration & Testing 19
- Chapter 3: Development Environment 27
- Product Overview
- Introduction
- Performance Specifications
- Electrical Interface
- Pin Functions
- Pin 1 (VIN)
- Pin 2 (LPP TX) and Pin 3 (LPP RX)
- Pin 4 (DIGITAL_IO1) and Pin 11 (DIGITAL_IO2)
- Pin 5 (ANALOG_IN1) and Pin 10 (ANALOG_IN2)
- Pins 6 and 7 (GND)
- Pin 8 (LOW_RF_POWER)
- Pin 9 (PWR_DN)
- Pin 12 (TPP RX) and Pin 13 (TPP TX)
- Pin 14 (3.3V_Logic_supply)
- USB Programming Cable
- USB Cable Installation
- Antennas
- External Antenna
- On-board Antenna
- Additional Specifications
- Dimensions: Gridstream S4SBR 25-1681 / 25-1682
- Dimensions: Gridstream S4SBR 25-1683 / 25-1684
- Configuration & Testing
- Development Environment
- Gridstream SCADA/DA Series 4 Single Board Radio Interface Board
- Transparent Port (TPP) Connection
- LAN Packet Port (LPP) Connection
- Onboard Regulator
- Digital Input
- Analog Input
- General Usage Instruction
- Gridstream S4SBR Logic
- Control Register 1
- Control Register 2
- Digital I/O Functionality
- Analog Input Functionality
- Memory Location
- Manufacturer Contact Information
- External Antenna Specifications
- Ground Plane Specifications
- RF External Antenna Cable Specifications
- External Antenna Radiation Pattern
- Identifying a Reverse-Polarity Connector
- Specifications
- On-board Antenna Radiation Pattern
- FCC Class B
- RF Exposure
- Industry Canada
- Host FCC Label Requirement
- Data Sheets
- Whip Antenna P/N 16-1000-0
- RF External Antenna Cable P/N 21-1000-0
Landis+Gyr Chapter 3 - Development Environment
Gridstream SCADA/DA S4SBR 98-1138 Rev AD 33
Memory Location
INTRODUCTION INFORMATION
[7702-7703h] Analog to Digital Channel A1.
When A1 is set to "Analog to Digital" (Bit 2) this location will contain a 10-bit reading. The scale on
this board is from 0 to 2.5 volts. Voltages greater than 2.5 VDC will be reported as 2.5 VDC.
[7704-7705h] Analog to Digital Channel A2.
When A2 is set to “Analog to Digital” (Bit 6) this location will contain a 10-bit reading. The scale on
this board is from 0 to 2.5 volts. Voltages greater than 2.5 VDC will be reported as 2.5 VDC.
[7706-7709h] D1 Interrupt Counter.
If D1 is configured as an interrupt (Bit 2-3) then this location will count the number of interrupts that
have been detected.
NOTE: The interrupt counter is cleared each time interrupts are enabled.
5 Pin A2 State
When A2, bit 4 is "0" and bit 6 is "0", then bit 5 returns current state as
"0" or "1".
When A2, bit 4 is "0" and bit 6 is "1", then read location 7704-7705
which returns the Hex value of the sampled voltage between 0-2.5
VDC.
When A2, bit 4 is "1", then the value of bit 5 can be set.
0
6Pin A2 Control
0: General Purpose I/O
1: Analog to Digital Channel (Bit 0 = "0" only)
0
7 Reserved Not Used 0
Table 3 - 3. Control Register 2
Bit Feature Description Dflt.
draft 29 Jan 2013