LANCOM Systems GmbH Adenauerstr. 20/B2 52146 Würselen Germany E-Mail: info@lancom.eu Internet www.lancom.eu . . . c o n n e c t i n g y o u r b u s i n e s s 110634/0409 LANCOM GS-2124 110643_LC-GS2124-MANUAL_cover.in1 1 20.04.
LANCOM GS-2124
© 2009 LANCOM Systems GmbH, Wuerselen (Germany). All rights reserved. While the information in this manual has been compiled with great care, it may not be deemed an assurance of product characteristics. LANCOM Systems shall be liable only to the degree specified in the terms of sale and delivery. The reproduction and distribution of the documentation and software supplied with this product and the use of its contents is subject to written authorization from LANCOM Systems.
LANCOM GS-2124 쮿 Preface Preface Thank you for your confidence in us! The LANCOM GS-2124 switch features 20 Fast-Ethernet and four combo ports (TP/SFP), it integrates perfectly into LANCOM's Advanced Routing und Forwarding and it supports up to 256 active VLANs. It uses bandwidth control to prioritize the data traffic according to predefined criteria (e.g. voice data or certain ports).
LANCOM GS-2124 쮿 Preface Information symbols EN 4 Very important instructions. Failure to observe these may result in damage. Important instruction that should be observed. Additional information that may be helpful but is not essential.
LANCOM GS-2124 쮿 Contents Contents 1.1 Key Features in the Device 1.2 Just what can your LANCOM Switch do? 2 Installation 9 9 10 13 2.1 Package content 13 2.2 System requirements 13 2.3 Status displays and interfaces 14 2.3.1 Connectors, LEDs and buttons on the LANCOM GS-2124 14 2.3.2 Connectors on rear of the LANCOM GS-2124 15 2.4 Mounting and connecting up the LANCOM Switch 15 2.5 Software installation 2.5.1 Starting the software setup 2.5.
LANCOM GS-2124 EN 쮿 Contents 6 4 Operation of Web- based Management 27 4.1 Web Management Home Overview 28 4.2 System: Basic Config 4.2.1 System Information 31 31 4.3 Account 4.3.1 Time 4.3.2 IP Configuration 4.3.3 Loop Detection 4.3.4 Management Policy 4.3.5 System Log 4.3.6 Virtual Stack 4.3.7 System: Port 4.3.8 Configuration 4.3.9 Port Status 4.3.10 Simple Counter 4.3.11 Detail Counter 33 33 36 38 39 42 43 45 46 48 51 52 4.4 Security: MAC 4.4.1 Mac Address Table 4.4.2 Static Filter 4.4.
LANCOM GS-2124 쮿 Contents 93 4.9 Security: 802.1x Configuration 4.9.1 Server 4.9.2 Port Configuration 4.9.3 Status 4.9.4 Statistics 94 98 100 103 104 4.10 Security: Mirror 105 4.11 Configuration: GVRP 4.11.1 Config 4.11.2 Counter 4.11.3 Group 106 107 109 111 4.12 Configuration: QoS (Quality of Service) Configuration 4.12.1 Ports 4.12.2 Qos Control List 4.12.3 Rate Limiters 4.12.4 Storm Control 4.12.5 Wizard 112 113 114 117 118 119 4.13 Configuration: Trunk 4.13.1 Port 4.13.2 Aggregator View 4.13.
LANCOM GS-2124 EN 쮿 Contents 4.18 Management: Diagnostics 4.18.1 Diag 4.18.2 Ping 149 149 150 4.19 Management: Maintenance 4.19.1 Reset device 4.19.2 Firmware upgrade 150 150 151 4.20 Management: SNMP 152 4.21 Logout 154 5 Operation of CLI Management 155 155 5.2 Commands of CLI 5.2.1 Global Commands of CLI 5.2.2 4-2-2. Local Commands of CLI 156 156 162 6 Appendix 8 155 5.1 CLI Management 5.1.1 Login 274 6.1 Performance data and specifications 274 6.2 Connector wiring 6.2.
LANCOM GS-2124 쮿 Chapter 1: Introduction 1 Introduction The switch can be managed through RS-232 serial port via directly connection, or through Ethernet port using Telnet or Web-based management unit, associated with SNMP agent. With the SNMP agent, the network administrator can logon the switch to monitor, configure and control each port’s activity in a friendly way. The overall network management is enhanced and the network efficiency is also improved to accommodate high bandwidth applications.
LANCOM GS-2124 쮿 Chapter 1: Introduction 쮿 Port Trunking: Support static port trunking and port trunking with IEEE 802.3ad LACP. 쮿 Bandwidth Control: Support ingress and egress per port bandwidth control. 쮿 Port Security: Support allowed, denied forwarding and port security with MAC address. EN 쮿 SNMP/RMON: SNMP agent and RMON MIB.
LANCOM GS-2124 쮿 Chapter 1: Introduction LANCOM GS2124 Full-duplex flow control (IEEE802.3x) and half-duplex backpressure ✔ System: Power ✔ TP Port 1-24: LINK/ACT, SPD ✔ SFP-Ports 21,22,23,24: LINK/ACT, SPD, SFP ✔ EN Ssatus LEDs PoE support PoE with 48VDC power through RJ-45 pin 1, 2, 3, 6. Powered Device(PD) auto detection and classification. PoE-PSE status and activity LED indicator.
LANCOM GS-2124 쮿 Chapter 1: Introduction EN LANCOM GS2124 Diagnostics to let administrator knowing the hardware status ✔ External loopback test to check if the link is ok ✔ HTTP for firmware upgrade, system log upload and config file import/ export ✔ Remote boot the device through user interface and SNMP ✔ Network time synchronization and daylight saving ✔ 120 event log records in the main memory and display on the local console ✔ Options LANCOM SFP Transceiver: Item no.
LANCOM GS-2124 쮿 Chapter 2: Installation 2 Installation This chapter will assist you to quickly install hardware and software. First, check the package contents and system requirements. The device can be installed and configured quickly and easily if all prerequisites are fulfilled. Package content Before beginning with the installation, please check that nothing is missing from your package.
LANCOM GS-2124 쮿 Chapter 2: Installation 2.3 Status displays and interfaces Meanings of the LEDs The following section describes the meaning of the LEDs. EN 2.3.1 Please be aware that LANmonitor shows far more information about the status of the LANCOM Switch than the LEDs '→ Monitoring the LANCOM switch with LANmonitor'.
LANCOM GS-2124 쮿 Chapter 2: Installation Port 1 to 24 쐆 10/100/1000 쮿 Constant green when the network connection is established to the connected device. 쮿 Blinks during data transfer. 쮿 Off if no network connection can be established to the connected device. 쮿 Constant green when the 1000 Mbps mode is active. 쮿 Constant orange when the 100 Mbps mode is active. 쮿 Off when the 10 Mbps is active. Mbps LED 쐊 SFP (LINK/ACT) LED 2.3.
LANCOM GS-2124 쮿 Chapter 2: Installation Use only standard TP cables of category CAT 5 or better with a maximum length of 100 m to ensure the best possible transfer of data. Cross-over cables can be used thanks to the auto-sensing function. If optical connections are to be used, additional modules can be purchased as accessories. EN 햴 Configuration via serial ports – In order to configure the LANCOM Switch directly, connect the serial configuration cable (supplied) to the COM port of the device.
LANCOM GS-2124 쮿 Chapter 2: Installation EN In Setup, select Install software. The following selection menus will appear on screen: 2.5.2 Which software should I install? 쮿 LANconfig is the Windows configuration program for all LANCOM devices. LANconfig searches for all LANCOM devices in your network. You can use this to start the Web-based configuration of a LANCOM Switch. 쮿 With LANmonitor you can use a Windows computer to monitor all of your LANCOM devices.
LANCOM GS-2124 쮿 Chapter 3: Configuring and monitoring the LANCOM Switch 3 Configuring and monitoring the LANCOM Switch 3.1 Configuration options There are two different methods of configuring the device. EN 쮿 By means of a graphical user interface or via a browser (WEBconfig). This option is only available if you have network access to the device's IP address from your computer. Instructions for configuring the device with WEBconfig are available in the chapter "Web-based configuration".
LANCOM GS-2124 쮿 Chapter 3: Configuring and monitoring the LANCOM Switch EN 쮿 If you do not have the device's IP number, LANconfig can be used to search for it. To start LANconfig click on Start 왘 Programs 왘 LANCOM 왘 LANconfig. LANconfig automatically searches for all available devices in your network. Any available LANCOM devices will be displayed in the list, including the LANCOM Switch. Double-click on this entry to start the browser automatically with the correct IP address.
LANCOM GS-2124 쮿 Chapter 3: Configuring and monitoring the LANCOM Switch 3.1.2 Starting the Command Line Interface over the network If you know the device's IP address (see section above) and the LANCOM Switch is accessible from your computer via the network, the you can use the command line interface via the network. 쐃 To do this, start a console such as Telnet and enter the device's IP address as the target. EN 쐇 Log on with user name and password (default: admin, admin). 3.1.
LANCOM GS-2124 쮿 Chapter 3: Configuring and monitoring the LANCOM Switch 쐋 Log on with user name and password (default: admin, admin). Which configuration does the device use? The switch supports four different configurations: The start configuration, the current working configuration, the user configuration and the default configuration. 쐃 Start configuration EN 3.2 At the system start, the device takes the parameters from the start configuration and copies these to the working configuration.
LANCOM GS-2124 쮿 Chapter 3: Configuring and monitoring the LANCOM Switch This is the default configuration and it cannot be altered. The web user interface has the following options to restore the switch to its default setting. EN 왏 With the function "restore default configuration included default IP address" you can reset the switch to the factory default settings (including the administrator´s password and the auto DHCP setting).
LANCOM GS-2124 쮿 Chapter 3: Configuring and monitoring the LANCOM Switch 쮿 User Configuration: It is the configuration file for the specified or backup purposes and can be updated while having confirmed the configuration. You can retrieve it by performing Restore User Configuration. Factory Defaults EN 3.3.1 쮿 Restore Default Configuration (includes default IP address) Restore Default Configuration function can retrieve ex-factory setting to replace the start configuration.
LANCOM GS-2124 쮿 Chapter 3: Configuring and monitoring the LANCOM Switch Save User EN 3.3.3 쮿 Save As User Configuration Save the current configuration as a user configuration file in flash memory. 3.3.4 Restore User 쮿 Restore User Configuration Restore User Configuration function can retrieve the previous confirmed working configuration stored in the flash memory to update start configuration.
LANCOM GS-2124 쮿 Chapter 3: Configuring and monitoring the LANCOM Switch Export/ Import Configuration File EN 3.4 쮿 Config File With this function, user can back up or reload the configuration files of Save As Start or Save As User via TFTP. 쮿 Parameter: 왏 Export File Path: Export Start: Export Save As Start's config file stored in the flash. Export User-Conf: Export Save As User's config file stored in the flash. 왏 Import File Path: Import Start: Import Save As Start's config file stored in the flash.
LANCOM GS-2124 EN 쮿 Chapter 3: Configuring and monitoring the LANCOM Switch 쮿 The left icon shows the config state: 왏 Gray: The port is deactivated in the configuration 왏 Yellow: The port is activated in the configuration 쮿 The right-hand icon shows the link state: 왏 Gray: No active network device is connected to the port 왏 Green: A network device is connected to the port and active Apart from the status, LANmonitor displays the VLAN ID for each port and the detected data rate at active ports connected t
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management This chapter instructs you how to configure and manage the LANCOM GS2124 through the web user interface it supports. With this facility, you can easily access and monitor through any one port of the switch all the status of the switch, including MIBs status, each port activity, Spanning tree status, port aggregation status, multicast traffic, VLAN and priority status, even illegal access record and so on.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN To optimize the display effect, we recommend you use Microsoft IE 6.0 above, Netscape V7.1 above or FireFox V1.00 above and have the resolution 1024x768. The switch supported neutral web browser interface. 4.1 Web Management Home Overview After you login, the switch shows you the system information.
LANCOM GS-2124 EN 쮿 Chapter 4: Operation of Web- based Management The Information of Page Layout On the top side, it shows the front panel of the switch. In the front panel, the linked ports will display green; as to the ports, which are link off, they will be dark. For the optional modules, the slot will show only a cover plate if no module exists and will show a module if a module is present. The image of module depends on the one you inserted.
LANCOM GS-2124 EN 쮿 Chapter 4: Operation of Web- based Management The figure shows the basic information of the clicked port. With this, you’ll see the information about the port status, traffic status and bandwidth rating for egress and ingress respectively. On the right-top corner, there is a pull-down list for Auto Logout. For the sake of security, we provide auto-logout function to protect you from illegal user as you are leaving.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 4.2.1 System: Basic Config System Information EN 4.2 쮿 System Information: Shows the basic system information. 쮿 Parameter: 왏 Model name: The model name of this device. 왏 System Description: As it is, this tells what this device is. Here, it is "L2 Plus Managed Switch" . 왏 Location: Basically, it is the location where this switch is put. User-defined.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 System up time: The time accumulated since this switch is powered up. Its format is day, hour, minute, second. EN 왏 Current time: Show the system time of the switch. Its format: day of week, month, day, hours : minutes : seconds, year. For instance, Tue Apr 20 23:25:58 2005. 왏 BIOS version: The version of the BIOS in this switch. 왏 Firmware version: The firmware version in this switch.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Account EN 4.3 In this function, only administrator can create, modify or delete the username and password. Administrator can modify other guest identities’ password without confirming the password but it is necessary to modify the administratorequivalent identity. Guest-equivalent identity can modify his password only.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management The switch provides manual and automatic ways to set the system time via NTP. Manual setting is simple and you just input “Year”, “Month”, “Day”, “Hour”, “Minute” and “Second” within the valid value range indicated in each item. If you input an invalid value, for example, 61 in minute, the switch will clamp the figure to 59. EN NTP is a well-known protocol used to synchronize the clock of the switch system time over a network.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Time Zone is an offset time off GMT. You have to select the time zone first and then perform time sync via NTP because the switch will combine this time zone offset and updated NTP time to come out the local time, otherwise, you will not able to get the correct time. The switch supports configurable time zone from –12 to +13 step 1 hour. 왏 Daylight Saving: Daylight saving is adopted in some countries.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management IP Configuration EN 4.3.2 IP configuration is one of the most important configurations in the switch. Without the proper setting, network manager will not be able to manage or view the device. The switch supports both manual IP address setting and automatic IP address setting via DHCP server.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Subnet mask: The subnet mask divides the IP address in two parts, one for the network and one for the device. The part of the network denotes the network of the computer. Only computer in the same network are able to communicate with each other. With devices of other networks can only be communicate through a router. The part of the device denotes the single device in a network.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Default: 192.168.1.254 왏 DNS: It is Domain Name System used to serve the translation between IP address and name address. EN The switch supports DNS client function to re-route the mnemonic name address to DNS server to get its associated IP address for accessing Internet. User can specify a DNS IP address for the switch. With this, the switch can translate a mnemonic name address into an IP address.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Loop Detection Display whether switch open Loop detection. 왏 Detection Port - Enable: When Port No is chosen, and enable port' s Loop detection, the port can detect loop happens. When Port-No is chosen, enable port' s Loop detection, and the port detects loop happen, port will be Locked. If Loop did not happen, port maintains Unlocked.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN 쐋 When only “deny lists” exist, then it will accept all connections, excluding the connection inside of the denying range. 쐏 When both “accept and deny” lists exist, then it will deny all connections, excluding the connection inside of the accepting range.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN be placed on the mode that the user connect to the switch, for example, we can decide that which VLAN VID is able to be accepted or denied by the switch, the IP range of the user could be accepted or denied by the switch, the port that the user is allowed or not allowed to connect with the switch, or the way of controlling and connecting to the switch via Http, Telnet or SNMP.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management the ports that you would like them to be worked and restricted in the management security configuration if ”Custom” had been chosen. EN 왏 Access Type: The switch supports two kinds of options for managed valid Access Type, including “Any” and “Custom”. Default is “Any”. “Http”, “Telnet” and “SNMP” are three ways for the access and managing the switch in case that” Custom” had been chosen.
LANCOM GS-2124 EN 쮿 Chapter 4: Operation of Web- based Management 쮿 System Log The Trap Log Data is displaying the log items including all SNMP Private Trap events, SNMP Public traps and user logs occurred in the system. In the report table, No., Time and Events are three fields contained in each trap record. 쮿 Parameter: 왏 No: Display the order number that the trap happened. Time: Display the time that the trap happened. 왏 Desc: Displays a description event recorded in the System Log.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management the network with knowing the address of the Master machine. Instead of SNMP or Telnet UI, VSM is only available in Web UI. While one switch become the Master, two rows of buttons for group device will appear on the top of its Web UI. By pressing these buttons, user will be allowed to connect the Web UI of the devices of the group in the same window without the login of these device. EN The most top-left button is only for Master device.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Group ID: It is the group identifier (GID) which signs for VSM. Valid letters are A-Z, a-z, 0-9, “ - “ and “_” characters. The maximal length is 15 characters. 4.3.7 System: Port This section contains the descriptions of the Port configuration, Port Status, Simple Counter and Detail Counter for port monitoring and management. Each of them will be described in detail orderly in the following section.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Configuration EN 4.3.8 Port Configuration is applied to change the setting of each port. In this configuration function, you can set/reset the following functions. 쮿 Port Configuration It is used to set each port’s operation mode. The switch supports 3 parameters for each port. They are State, Speed/Duplex and Flow Control. 쮿 Parameter 왏 Speed/Duplex: Set the speed and duplex of the port.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 100/1000Mbps, and duplex mode, full duplex and half duplex. The following table summarized the function the media supports. NWay Speed Duplex 100M TP ON/OFF 10/100M Full/Half 1000M TP ON/OFF 10/100/1000M Full for all, Half for 10/100 1000M Fiber ON/OFF 1000M Full EN Media type In Auto-negotiation mode, no default value. In Forced mode, default value depends on your setting.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Port Status EN 4.3.9 The function Port Status gathers the information of all ports’ current status and reports it by the order of port number, media, link status, port state, AutoNegotiation status, speed/duplex, Rx Pause and Tx Pause. An extra media type information for the module ports 21, 22, 23 and 24 is also offered. 쮿 Port Status Report the latest updated status of all ports in this switch.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Link: Show that if the link on the port is active or not. If the link is connected to a working-well device, the Link will show the link “Up”; otherwise, it will show “Down”. This is determined by the hardware on both devices of the connection. No default value. 왏 State: Show that the communication function of the port is “Enabled” or “Disabled”. When it is enabled, traffic can be transmitted and received via this port.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Rx Pause: The way that the port adopts to process the PAUSE frame. If it shows “on”, the port will care the PAUSE frame; otherwise, the port will ignore the PAUSE frame. Default: None EN 왏 Tx Pause: It decides that whether the port transmits the PAUSE frame or not. If it shows “on”, the port will send PAUSE frame; otherwise, the port will not send the PAUSE frame. Default: None.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Temperature: Show the current temperature of module. 왏 Vcc: Show the working DC voltage of module. 왏 Mon1(Bias) mA: Show the Bias current of module. EN 왏 Mon2(TX PWR): Show the transmit power of module. 왏 Mon3(RX PWR): Show the receiver power of module. 4.3.10 Simple Counter The function of Simple Counter collects any information and provides the counting about the traffic of the port, no matter the packet is good or bad.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Refresh Interval is used to set the update frequency. Default update time is 3 seconds. EN 쮿 Function name: Simple Counter 쮿 Function Description: Display the summary counting of each port’s traffic, including Tx Byte, Rx Byte, Tx Packet, Rx Packet, Tx Collision and Rx Error Packet. 쮿 Parameters Description: 왏 Tx Byte: Total transmitted bytes. 왏 Rx Byte: Total received bytes. 왏 Tx Packet: The counting number of the packet transmitted.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Each data field has 20-digit long. If the counting is overflow, the counter will be reset and restart counting. The data is updated every time interval defined by the user. The valid range is 3 to 10 seconds. The Refresh Interval is used to set the update frequency. Default update time is 3 seconds. EN 쮿 Detail Counter Display the detailed counting number of each port’s traffic.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Tx Deferred Transmit: Number of frames delayed to transmission due to the medium is busy. 왏 Tx Late Collision: Number of times that a collision is detected later than 512 bit-times into the transmission of a frame. EN 왏 Tx Excessive Collision: Number of frames that are not transmitted because the frame experienced 16 transmission attempts. 왏 Packets 64 Octets: Number of 64-byte frames in good and bad packets received.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Rx FCS Errors: Number of bad FSC packets received. 왏 Rx Alignment Errors: Number of Alignment errors packets received. 왏 Rx Jabbers: Number of long frames(according tomax_length register) with invalid CRC. 왏 Rx Drop Packets: Frames dropped due to the lack of receiving buffer. 왏 Rx Undersize Packets: Number of short frames (<64 Bytes) with valid CRC.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 MAC Address Table Information This function can allow the user to set up the processing mechanism of MAC Table. An idle MAC address exceeding MAC Address Age-out Time will be removed from the MAC Table. The range of Age-out Time is 101000000 seconds, and the setup of this time will have no effect on static MAC addresses. EN In addition, the learning limit of MAC maintenance is able to limit the amount of MAC that each port can learn.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Static Filter EN 4.4.2 쮿 Static Filter Static Filter is a function that denies the packet forwarding if the packet's MAC Address is listed in the filtering Static Filter table. User can very easily maintain the table by filling in MAC Address, VID (VLAN ID) and Alias fields individually. User also can delete the existed entry by clicking button.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Static Forward EN 4.4.3 쮿 Static Forward Static Forward is a function that allows the user in the static forward table to access a specified port of the switch. Static Forward table associated with a specified port of a switch is set up by manually inputting MAC address and its alias name. When a MAC address is assigned to a specific port, all of the switch's traffics sent to this MAC address will be forwarded to this port.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Alias: MAC alias name you assign. MAC Alias EN 4.4.4 쮿 MAC Alias MAC Alias function is used to let you assign MAC address a plain English name. This will help you tell which MAC address belongs to which user in the illegal access report. At the initial time, it shows all pairs of the existed alias name and MAC address.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Alias: MAC alias name you assign. Note: If there are too many MAC addresses learned in the table, we recommend you inputting the MAC address and alias name directly. MAC Table EN 4.4.5 쮿 Dynamic MAC Table Display the static or dynamic learning MAC entry and the state for the selected port. 쮿 Parameter: 왏 Type: Dynamic or Static. 왏 VLAN: VLAN identifier. This will be filled only when tagged VLAN is applied. Valid range is 1 ~ 4094.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Previous Page: Move to the previous page. 왏 Next Page: Move to the next page. Security: VLAN The switch supports Tag-based VLAN (802.1q) and Port-based VLAN. Support 256 active VLANs and VLAN ID 1~4094. VLAN configuration is used to partition your LAN into small ones as your demand. Properly configuring it, you can gain not only improving security and increasing performance but greatly reducing VLAN management. 4.5.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management name. This switch can support up to maximal 24 port-based VLAN groups. Tag-based: EN Tag-based VLAN identifies its member by VID. This is quite different from port-based VLAN. If there are any more rules in ingress filtering list or egress filtering list, the packet will be screened with more filtering criteria to determine if it can be forwarded. The switch supports supplement of 802.1q.
LANCOM GS-2124 왏 IGMP Proxy: IGMP proxy enables the switch to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The system acts as a proxy for its hosts. This switch can be set IGMP function "Enable" or "Disable" by VLAN group. If the VLAN group IGMP proxy is disabled, the switch will stop the exchange of IGMP messages in the VLAN group members.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN 4.5.3 Port-based Group 쮿 Port-based Group Configuration Function Description: It shows the information of the existed Port-based VLAN Groups. You can easily create, edit and delete a Port-based VLAN group by pressing , and function buttons. User can add a new VLAN group by inputting a new VLAN name. 쮿 Parameter: 왏 VLAN Name: The name defined by administrator is associated with a VLAN group.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN 왏 Member Port: This is used to enable or disable if a port is a member of the new added VLAN, “Enable” means it is a member of the VLAN. Just tick the check box beside the port x to enable it. 왏 Add a new VLAN: Create a new Port-based VLAN. Input the VLAN name and choose the member by ticking the check box beside the port No., then, press the button to have the setting taken effect.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN 왏 Delete Group: Just press the button to remove the selected group entry from the Port-based group table.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Ports EN 4.5.4 쮿 VLAN Port Configuration In VLAN Tag Rule Setting, user can input VID number to each port. The range of VID number is from 1 to 4094. User also can choose ingress filtering rules to each port. There are two ingress filtering rules which can be applied to the switch. The Ingress Filtering Rule 1 is "forward only packets with VID matching this port's configured VID". The Ingress Filtering Rule 2 is "drop untagged frame".
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Ingress Filtering: Discard other VLAN group packets, only forward this port joined VLAN group packets 왏 Frame Type: All: Forward all tagged and untagged packets Tagged: Forward tagged packets only and discard untagged packets EN 왏 PVID: This PVID range will be 1-4094. Before you set a number x as PVID, you have to create a Tag-based VLAN with VID x.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쐇 Assign port member to the VLAN2 쐋 You need to assign these ports for member of port isolation. 쐏 Press the "Save" to complete the PVLAN configuration process. Management VLAN EN 4.5.6 쮿 Management VLAN To assign a specific VLAN for management purpose. 쮿 Parameter: 왏 VID: Specific Management VLAN ID. 4.6 Security: ACL The LANCOM GS-2124 switch access control list (ACL) is probably the most commonly used object in the IOS.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Ports EN 4.6.1 쮿 ACL Port Configuration The switch ACL function support up to 128 Access Control Entries (ACEs), using the shared 128 ACEs for ingress classification. You can create an ACE and assign this ACE for each port with or assign this ACE for a policy or assign this ACE for a port.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Policy ID: Policy ID range:1~8 왏 Action: Permit or Deny forwarding the met ACL packets Rate Limiter ID Range: 1~16. To select one of rate limiter ID for this port, it will limit met ACL packets by rate limiter ID configuration. 왏 Port Copy: Disabled: Disable to copy the met ACL packets to specific port. Port number: 1~24. Copy the met ACL packets to the selected port.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 Rate Limiter ID: ID Range: 1~16 EN 왏 Rate(pps): 1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1K / 2K / 4K / 8K / 16K / 32K / 64K / 128K / 256K / 512K / 1024K 4.6.3 Access Control List 쮿 ACL Rate Limiter Configuration The switch ACL function support up to 128 Access Control Entries (ACEs), using the shared 128 ACEs for ingress classification.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 Frame Type: Range: Any / Ethernet Type / ARP / IPv4 Any: It is including all frame type Ethernet Type: It is including all Ethernet frame type EN ARP: It is including all ARP protocol frame type IPv4: It is including all IPv4 protocol frame type 쮿 ACE Configuration The switch ACL function support up to 128 Access Control Entries (ACEs), using the shared 128 ACEs for ingress classification.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 MAC Parameters: (When Frame Type = Any) DMAC Filter: Range: Any / MC / BC / UC Any: It is including all destination MAC address MC: It is including all Multicast MAC address BC: It is including all Broadcast MAC address EN UC: It is including all Unicast MAC address 왏 MAC Parameters: (When Frame Type = Ethernet Type) SMAC Filter: Range: Any / Specific Any: It is including all source MAC address Specific: It is according to SMAC Value specifi
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 MAC Parameters: (When Frame Type = ARP) SMAC Filter: Range: Any / Specific Any: It is including all source MAC address EN Specific: It is according to SMAC Value specific the source MAC address DMAC Filter: Range: Any / MC / BC / UC Any: It is including all destination MAC address MC: It is including all Multicast MAC address BC: It is including all Broadcast MAC address UC: It is including all Unicast MAC address 왏 MAC Parameters: (When Fr
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 ARP Parameters: (When Frame Type = ARP) ARP/RARP: Range: Any / ARP / RARP / Other Any: Including all ARP/RARP protocol frame types ARP: Including all ARP protocol frame types EN RARP: Including all RARP frame types Other: Including other frame types except ARP/RARP protocol Request/Reply: Range: Any / Request / Reply Any: Including all ARP/RARP Request and Reply Request: Including all ARP/RARP request frames Reply: Including all ARP/RARP rep
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management equal SMAC under MAC parameter setting 1: The ingress ARP frames where the source MAC address is equal SMAC address under MAC parameter setting RARP DMAC Match: Range: Any / 0 / 1 0: The ingress RARP frames where the Destination MAC address is not equal DMAC address under MAC parameter setting 1: The ingress RARP frames where the Destination MAC address is equal DMAC address under MAC parameter setting IP/Ethernet Length: Range: Any / 0 / 1 Any
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 IP Parameters: (When Frame Type = IPv4 and IP Protocol Filter = Any) IPTTL: (Time To Live) How many routers a datagram can pass through. Each router decrements this value by 1 until it reaches 0 when the datagram is discarded.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management ted, whether the datagram is fragmented, and whether the current fragment is the final one. Range: Any / Yes / No Any: Including all IP fragment case Yes: The ingress frame is fragmented packet EN No: The ingress frames is not fragmented packet IP Option: A list of optional specifications for security restrictions, route recording, and source routing. Not every datagram specifies an options field.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 IP Parameters: (Frame Type = IPv4 and IP Protocol Filter = ICMP) ICMP Type Filter: Range: Any / Specific Any: Including all types of ICMP type values EN Specific: According to following ICMP type value setting for ingress classification ICMP Type Value: Range: 0-255 ICMP Code Filter: Range: Any / Specific Any: Including all of ICMP code values Specific: According to following ICMP code value setting for ingress classification ICMP Code Valu
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 IP Parameters: (Frame Type = IPv4 and IP Protocol Filter = UDP) Source Port Filter: Range: Any / Specific / Range Any: Including all UDP source ports Range: According to following Source Port Range setting for ingress classification. Source Port No.: Range: 0-65535 Source Port Range.: Range: 0-65535 Dest. Port Filter: Range: Any / Specific / Range Any: Including all UDP destination ports Specific: According to following Dest. Port No.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 IP Parameters: (Frame Type = IPv4 and IP Protocol Filter = TCP) Source Port Filter: Range: Any / Specific / Range Any: Including all TCP source ports EN Specific: According to following Source Port No. setting for ingress classification Range: According to following Source Port Range setting for ingress classification Source Port No.: Range: 0-65535 Source Port Range.: Range: 0-65535 Dest.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management TCP RST: TCP Control Bit RST: Means Reset the connection Range: Any / 0 / 1 Any: Including all TCP RST case 0: The TCP control bit RST is 0 EN 1: The TCP control bit RST is 1 TCP PSH: TCP Control Bit PSH: Means Push Function Range: Any / 0 / 1 Any: Including all TCP PSH case 0: The TCP control bit PSH is 0 1: The TCP control bit PSH is 1 TCP ACK: TCP Control Bit ACK: Means Acknowledgment field significant Range: Any / 0 / 1 Any: Including all
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Range: Any / 0 / 1 Any: Including all IP protocol value case 0: The IP protocol value is 0 1: The IP protocol value is 1 EN 왏 IP Parameters: (Frame Type = IPv4 and IP Protocol Filter = Other) IP Protocol Value: Default: 255 IPTTL: (Time To Live) How many routers a datagram can pass through. Each router decrements this value by 1 until it reaches 0 when the datagram is discarded.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management ed, whether the datagram is fragmented, and whether the current fragment is the final one. Range: Any / Yes / No Any: Including all IP fragment case Yes: The ingress frame is fragmented packet EN No: The ingress frames is not fragmented packet IP Option: A list of optional specifications for security restrictions, route recording, and source routing. Not every datagram specifies an options field.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 VLAN Parameters: VLAN ID Filter: Range: Any / Specific Any: Including all VLAN IDs EN Specific: According to following VLAN ID and Tag Priority setting for ingress classification VLAN ID: Range: 1-4094 Tag Priority: Range: Any / 0-7 Any: Including all Tag Priority values 0-7: The Tag Priority Value is one of number (0-7) Action Parameters: When the ingress frame meet above ACL ingress classification rule you can do the following actions: Ac
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Wizard EN 4.6.4 쮿 Wizard The wizard function is provide 4 type of typical application for user easy to configure their application with ACL function. 쮿 Parameter: 왏 Please select an Action: Set up Policy Rules / Set up Port Policies / Set up Typical Network Application Rules / Set up Source MAC and Source IP Binding 왏 Next: Click on to confirm current setting and go to next step automatically.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 Common Server: DHCP / DNS / FTP / HTTP / IMAP / NFS / POP3 / SAMBA / SMTP / TELNET / TFTP 왏 Instant Messaging: Google Talk / MSN Messenger / Yahoo Messenger EN 왏 User Definition: Ethernet Type / UDP Port / TCP Port 왏 Others: TCP Port / ICMP / Multicast IP Stream / NetBIOS / Ping Request / Ping Reply / SNMP / SNMP Traps 왏 Ingress Port: Any / Policy1-8 / Port1-24 왏 Action: Permit / Deny 왏 Rate Limiter ID: Disabled / 1-16 쮿 Paramet
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN the authorized client can access the Switch's port by checking the pair of IPMAC. Addresses and port number with the pre-configured database. If an unauthorized user tries to access an IP-MAC binding enabled port, the system will block the access by dropping its packet. 쮿 IP MAC Binding Configuration The switch has client and server two classes of IP-MAC Binding table. The maximum number of IP-MAC binding client table is 512 entries.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 MAC: Six-byte MAC Address: xx-xx-xx-xx-xx-xx (For example: 00-40-c700-00-01) 왏 IP: Four-byte IP Address: xxx.xxx.xxx.xxx (For example: 192.168.1.100) EN 왏 Port No: Port no.: 1-24 왏 VID: VLAN ID: 1-4094 왏 Add: Input MAC, IP, Port and VID, then click on to create a new entry into the IP MAC Binding table 왏 Delete: Select one of entry from the table, then click on to delete this entry. 4.8 4.8.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 DHCP Snooping state: The parameter which set to disabled or enabled the DHCP snooping function on the switch, the default is Disabled. Note: To click " Apply" when you finish the configuration. 4.8.2 DHCP Snooping Entry 쮿 DHCP Snooping Entry DHCP snooping Entry allows a switch to add the an trust DHCP server and 2 trust port to build the DHCP snooping available entry.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 VID: When DHCP snooping is enabled, and enabled on the specified VLAN, DHCP packet filtering will be performed on any un-trusted ports within the VLAN. It set a available VLAN ID to enable the DHCP snooping on VLAN interface. EN 왏 Trust Port 1: If DHCP snooping is enabled globally, and also enabled on the VLAN where the DHCP packet is received, all DHCP packets are forwarded for a trusted por. It set a trust port 1.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management cation is enabled, then the packet will only be forwarded if the client's hardware address stored in the DHCP packet is the same as the source MAC address in the Ethernet header. 왏 If a DHCP packet from a client passes the filtering criteria above, it will only be forwarded to trusted ports in the same VLAN.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 4.9 Security: 802.1x Configuration EN 802.1x port-based network access control provides a method to restrict users to access network resources via authenticating user’s information. This restricts users from gaining access to the network resources through a 802.1xenabled port without authentication. If a user wishes to touch the network through a port under 802.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management A port acting as an authenticator is thought to be two logical ports, a controlled port and an uncontrolled port. A controlled port can only pass the packets when the authenticator PAE is authorized, and otherwise, an uncontrolled port will unconditionally pass the packets with PAE group MAC address, which has the value of 01-80-c2-00-00-03 and will not be forwarded by MAC bridge, at any time.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN In this figure is the typical configuration, a single supplicant, an authenticator and an authentication server. B and C is in the internal network, D is Authentication server running RADIUS, switch at the central location acts Authenticator connecting to PC A and A is a PC outside the controlled port, running Supplicant PAE.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쐋 The authenticator always periodically sends EAP-Request/Identity to the supplicant for requesting the identity it wants to be authenticated. 쐄 And next, the Supplicant replies an EAP-Response/Identity to the authenticator. The authenticator will embed the user ID into Radius-AccessRequest command and send it to the authentication server for confirming its identity.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management authorized, the devices connected to this port can access the network resource through this port. EN 802.1x Port-based Network Access Control function supported by the switch is little bit complex, for it just support basic Multihost mode, which can distinguish the device’s MAC address and its VID. The following table is the summary of the combination of the authentication status and the port status versus the status of port mode, set in 802.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 Authentication Server Server IP Server: Server IP address for authentication. Default: 192.168.1.1 EN UDP Port: Default port number is 1812. Secret Key: The secret key between authentication server and authenticator. It is a string with the length 1 - 31 characters. The character string may contain upper case, lower case and 0-9. It is character sense. It is not allowed for putting a blank between any two characters.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Port Configuration EN 4.9.2 쮿 802.1X Port Configuration This function is used to configure the parameters for each port in 802.1X port security application. Refer to the following parameters description for details. Parameter: 왏 Port: It is the port number to be selected for configuring its associated 802.1X parameters which are Port control, reAuthMax, txPeriod, Quiet Period, reAuthEnabled, reAuthPeriod, max.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Port Control: This is used to set the operation mode of authorization. There are three type of operation mode supported, ForceUnauthorized, ForceAuthorized, Auto. ForceAuthorized: The controlled port is forced to hold in the authorized state. Auto: The controlled port is set to be in authorized state or unauthorized state depends on the result of the authentication exchange between the authentication server and the supplicant.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 max. Request(1-10): The maximum of number times that the authenticator will retransmit an EAP Request to the supplicant before it times out the authentication session. The valid range: 1 - 10. Default: 2 times EN 왏 suppTimeout(1-65535 s): A timeout condition in the exchange between the authenticator and the supplicant. The valid range: 1 -65535. Default: 30 seconds.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Status EN 4.9.3 쮿 802.1X Status Show the each port IEEE 802.1X authentication current operating mode and status. 쮿 Parameter: 왏 Port: Port number: 1-24 왏 Mode: Show this port IEEE 802.1X operating mode: There are four modes Disable, Normal, Advance and Clientless 왏 Status: Show this port IEEE 802.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Statistics EN 4.9.4 쮿 802.1X Port Statistics Port1 Show the IEEE 802.1X authentication related counters for manager monitoring authenticator status.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Security: Mirror EN 4.10 쮿 Mirror Configuration Mirror Configuration is to monitor the traffic of the network. For example, we assume that Port A and Port B are Monitoring Port and Monitored Port respectively, thus, the traffic received by Port B will be copied to Port A for monitoring. Note: When configure the mirror function, you should avoid setting a port to be a sniffer port and aggregated port at the same time.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Port #: Range: 1-24 Select the monitored ports. 왏 Source Enable: The source enable means the monitored port ingress traffic will be copied to monitoring port. EN 왏 Destination Enable: The destination enable means the monitored port egress traffic will be copied to monitoring port. 4.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Config EN 4.11.1 쮿 GVRP Config In the function of GVRP Config, it is used to configure each port’s GVRP operation mode, in which there are seven parameters needed to be configured described below. 쮿 Parameter: 왏 GVRP State Setting: This function is simply to let you enable or disable GVRP function. You can pull down the list and click the arrow key to choose “Enable” or “Disable”.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Leave Time: Used to declare the Leave Time in unit of centisecond. Valid time range: 60 –300 centisecond, Default: 60 centisecond. EN 왏 Leave All Time: A time period for announcement that all registered device is going to be de-registered. If someone still issues a new join, then a registration will be kept in the switch. Valid range: 1.000-5.000 unit time, Default: 1.000 unit time.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Restricted Mode: This function is used to restrict dynamic VLAN be created when this port received GVRP PDU (Protocol Data Unit). There are two modes, disable and enable, provided for the user’s choice. In this mode, the switch dynamic VLAN will be created when this port received GVRP PDU. The default setting is Normal. Enabled: In this mode, the switch does not create dynamic VLAN when this port received GVRP PDU.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 Received: Total GVRP Packets: Total GVRP BPDU is received by the GVRP application. Invalid GVRP Packets: EN Number of invalid GARP BPDU is received by the GARP application. LeaveAll Message Packets: Number of GARP BPDU with Leave All message is received by the GARP application. JoinEmpty Message Packets: Number of GARP BPDU with Join Empty message is received by the GARP application.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Transmitted: Total GVRP Packets: Total GARP BPDU is transmitted by the GVRP application. Invalid GVRP Packets: EN Number of invalid GARP BPDU is transmitted by the GVRP application. LeaveAll Message Packets: Number of GARP BPDU with Leave All message is transmitted by the GARP application. JoinEmpty Message Packets: Number of GARP BPDU with Join Empty message is transmitted by the GARP application.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Member Port: Those are the members belonging to the same dynamic VLAN group. EN 왏 Edit Administrative Control: When you create GVRP group, you can use Administrative Control function to change Applicant Mode and Registrar Mode of GVRP group member. 4.12 Configuration: QoS (Quality of Service) Configuration The switch support four QoS queues per port with strict or weighted fair queuing scheduling.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Ports EN 4.12.1 쮿 Port QoS Configuration To configure each port QoS behavior. Four QoS queue per port with strict or weighted fair queuing scheduling. There are 24 QoS Control Lists (QCL) for advance programmable QoS classification, based on IEEE 802.1p, Ethertype, VID, IPv4/IPv6 DSCP and UDP/TCP ports and ranges.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Default Class: User can set up High Priority or Low Priority for each port respectively. Low / Normal / Medium / High 왏 QCL: The number of QCL rule 1~24, each port have to apply one of the QCL rule for QoS behavior EN 왏 User priority: The user priority value 0~7 (3 bits) is used as an index to the eight QoS class values for VLAN tagged or priority tagged frames.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 QCL#: QCL number : 1~24 왏 Ethernet Type Value: The configurable range is 0x600~0xFFFF. Well known protocols already assigned EtherType values. The commonly used values in the EtherType field and corresponding protocols are listed below: Ethertype (Hexadecimal) Protocol 0x0800 IP, Internet Protocol 0x0801 X.75 Internet 0x0802 NBS Internet 0x0803 ECMA Internet 0x0804 Chaosnet 0x0805 X.
LANCOM GS-2124 EN 쮿 Chapter 4: Operation of Web- based Management Ethertype (Hexadecimal) Protocol 0x8847 MPLS, Multi-Protocol Label Switching (unicast). 0x8848 MPLS, Multi-Protocol Label Switching (multicast). 0x8863 PPPoE, PPP Over Ethernet (Discovery Stage). 0x8864 PPPoE, PPP Over Ethernet (PPP Session Stage). 0x88BB LWAPP, Light Weight Access Point Protocol. 0x88CC LLDP, Link Layer Discovery Protocol. 0x8E88 EAPOL, EAP over LAN.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Rate Limiters EN 4.12.3 쮿 Rate Limit Configuration Each port includes an ingress policer, and an egress shaper, which can limit the bandwidth of received and transmitted frames. Ingress policer or egress shaper operation is controlled per port in the Rate Limit Configuration. 쮿 Parameter: 왏 Port #: Port number. 왏 Policer Enabled: Policer enabled to limit ingress bandwidth by policer rate.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Policer Rate: The configurable policer rate range: 500 Kbps ~ 1000000 Kbps 1 Mbps ~ 1000 Mbps EN 왏 Policer Unit: There are two units for ingress policer rate limit: kbps / Mbps 왏 Shaper Enabled: Shaper enabled to limit egress bandwidth by shaper rate. 왏 Shaper Rate: The configurable shaper rate range: 500 Kbps ~ 1000000 Kbps 1 Mbps ~ 1000 Mbps 왏 Shaper Unit: There are two units for egress shaper rate limit: kbps / Mbps 4.12.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Rate(pps): Refer to the following rate configurable value list, the unit is Packet Per Second (pps). 1 / 2 / 4 / 8 / 16 / 32 / 64 / 128 / 256 / 512 / 1K / 2K / 4K / 8K / 16K / 32K / 64K / 128K / 256K / 512K / 1024K Wizard EN 4.12.5 쮿 Wizard The QCL configuration Wizard is targeted on user can easy to configure the QCL rules for QoS configuration.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Cancel: Abort current configuration back to previous step. 왏 Back: Back to previous screen. 왏 QCL ID: QoS Control List (QCL): 1~24 EN 왏 Port Member: Port Member: 1~24 왏 Wizard Again: Click on the , back to QCL Configuration Wizard. 왏 Finish: When you click on , the parameters will be set according to the wizard configuration and shown on the screen, then ask you to click on for changed parameters confirmation.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 QCL #: QoS Control List (QCL): 1~24 왏 QCL ID: QoS Control List (QCL): 1~24 왏 TOS Precedence 0~7 Class: Low / Normal / Medium / High EN 왏 QCL ID: QoS Control List (QCL): 1~24 왏 Tag Priority 0~7 Class: Low / Normal / Medium / High 4.13 Configuration: Trunk The Port Trunking Configuration is used to configure the settings of Link Aggregation.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN Ports using Static Trunk as their trunk method can choose their unique Static GroupID (also 1~3, this Static groupID can be the same with another LACP groupID) to form a logic “trunked port”. The benefit of using Static Trunk method is that a port can immediately become a member of a trunk group without any handshaking with its peer port.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Port EN 4.13.1 쮿 Trunk Port Setting/Status Port setting/status is used to configure the trunk property of each and every port in the switch system.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Method: This determines the method a port uses to aggregate with other ports. None: A port does not want to aggregate with any other port should choose this default setting. LACP: A port use LACP as its trunk method to get aggregated with other ports also using LACP. EN Static: A port use Static Trunk as its trunk method to get aggregated with other ports also using Static Trunk.
LANCOM GS-2124 EN 쮿 Chapter 4: Operation of Web- based Management 125
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Aggregator View EN 4.13.2 쮿 Aggregator view To display the current port trunking information from the aggregator point of view. 쮿 Parameter: 왏 Aggregator: It shows the aggregator ID (from 1 to 26) of every port. In fact, every port is also an aggregator, and its own aggregator ID is the same as its own Port No.. 왏 Method: Show the method a port uses to aggregate with other ports.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Member Ports: Show all member ports of an aggregator (port). EN 왏 Ready Ports: Show only the ready member ports within an aggregator (port). 4.13.3 Hash Method DA+SA, DA and SA are three Hash methods offered for the Link Aggregation of the switch. Packets will decide the path to transmit according to the mode of Hash you choose.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 4.13.4 LACP System Priority EN 쮿 LACP System Priority It is used to set the priority part of the LACP system ID. LACP will only aggregate together the ports whose peer link partners are all on a single system. Each system supports LACP will be assigned a globally unique System Identifier for this purpose. A system ID is a 64-bit field comprising a 48-bit MAC Address and 16-bit priority value.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management STP Status EN 4.14.1 쮿 STP Status In the Spanning Tree Status, user can read 12 parameters to know STP current status. The 12 parameters’ description is listed in the following table. 쮿 Parameter: 왏 STP State: Show the current STP Enabled / Disabled status. Default is “Disabled”. 왏 Bridge ID: Show switch’s bridge ID which stands for the MAC address of this switch. 왏 Bridge Priority: Show this switch’s current bridge priority setting.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Root Path Cost: Show the path cost between the root port and the designated port of the root bridge. EN 왏 Current Max. Age: Show the current root bridge maximum age time. Maximum age time is used to monitor if STP topology needs to change.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Configuration EN 4.14.2 The STP, Spanning Tree Protocol, actually includes RSTP. In the Spanning Tree Configuration, there are six parameters open for the user to configure as user’s idea. Each parameter description is listed below. 쮿 STP Configuration User can set the following Spanning Tree parameters to control STP function enable/disable, select mode RSTP/STP and affect STP state machine behavior to send BPDU in this switch.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management When the LANCOM Switch is the root bridge of the LAN, for example, all other bridges will use the hello time assigned by this switch to communicate with each other. The valid value is 1 ~ 10 in unit of second. Default is 2 seconds. EN 왏 Max. Age: When the LANCOM Switch is the root bridge, the whole LAN will apply this figure set by this switch as their maximum age time.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Port EN 4.14.3 쮿 STP Port Setting In the STP Port Setting, one item selection and five parameters settings are offered for user’s setup. User can disable and enable each port by selecting each Port Status item. User also can set “Path Cost” and “Priority” of each port by filling in the desired value and set “Admin Edge Port” and “Admin Point To Point” by selecting the desired item.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 Port Status: It displays the current state of a port. We cannot manually set it because it displays the status only. There are three possible states. ( according to 802.1w specification) EN “Discarding State” indicates that this port can neither forward packets nor contribute learning knowledge. Notice: Three other states (“disable state”, “blocking state” and “listening state”) defined in the 802.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Admin Edge Port: If user selects “Yes”, this port will be an edge port. An Edge Port is a port connected to a device that knows nothing about STP or RSTP. Usually, the connected device is an end station. Edge Ports will immediately transit to forwarding state and skip the listening and learning state because the edge ports cannot create bridging loops in the network. This will expedite the convergence.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN VLANs to follow separate paths, each based on an independent Multiple Spanning Tree Instance (MSTI), within Multiple Spanning Tree (MST) Regions composed of LANs and or MST Bridges. Proper configuration of MSTP in an 802.1Q VLAN environment can ensure a loop-free data path for a group of VLANs within an MSTI. Redundant path and load balancing in VLAN environment is also achieved via this feature.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 Region Name: 0-32 characters.(A variable length text string encoded within a fixed field of 32 octets , conforming to RFC 2271's definition of SnmpAdminString.) 4.15.3 EN 왏 Revision Level: 0-65.535 Instance View 쮿 MSTP Instance Config Providing an MST instance table which include information (VLAN membership of a MSTI ) of all spanning instances provisioned in the particular MST region which the bridge belongs to.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Corresponding VLANs: 0-4095. Multiple VLANs can belong to an MSTI. All VLANs that are not provisioned through this will be automatically assigned to Instance 0(CIST). EN 왏 Edit MSTI / VLAN: See Figure. To add an MSTI and provide its VLAN members or modify VLAN members for a specific MSTI. 왏 Del MSTI: To delete an MSTI. 왏 Del All MSTI: Deleting all provisioned MSTIs at a time. 왏 Instance Configuration: See Figure.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 MAX. Age: 6-40sec. The same definition as in the RSTP protocol. 왏 MAX. Hops: 6-40sec. It's a new parameter for the multiple spanning tree protocol. It is used in the internal spanning tree instances. "CIST Remaining Hops" or "MSTI Remaining Hops" in the Spanning tree protocol message would decreased by one when the message is propagated to the neighboring bridge.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN 왏 Restricted Role: Yes / No. If "Yes" causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Port after the Root Port has been selected. This parameter is "No" by default. If set, it can cause lack of spanning tree connectivity.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Bridge Mac Address: The Mac Address of the bridge itself. 왏 CIST ROOT PRIORITY: Spanning tree priority value of the CIST root bridge. 왏 CIST EXTERNAL ROOT PATH COST: Root path cost value from the point of view of the bridge's MST region. 왏 CIST ROOT PORT ID: The port ID of the bridge's root port. In MSTP, peer port of a root port may reside in defferent MST region or in the same MST region.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Notification receiving" to occur. When new series of Topology Changes occur again, this counter will be reset to 0. EN 왏 TOPOLOGY CHANGE COUNT(SECs): The per spanning tree instanceTopology Change Count expresses the time spent in unit of seconds since the beginning of the Spanning Tree Topology Change to the end of the STP convergence.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Restricted Tcn: Same as mentioned in "Port Config" Configuration: Multicast The function, IGMP Snooping, is used to establish the multicast groups to forward the multicast packet to the member ports, and, in nature, avoids wasting the bandwidth while IP multicast packets are running over the network.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 4.16.2 Proxy IGMP proxy enables the switch to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The switch acts as a proxy for its hosts. EN You enable IGMP proxy on the switch, which connects to a router closer to the root of the tree. This interface is the upstream interface. The router on the upstream interface should be running IGMP.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 Last Member Query Max Response Time : To set the max response code value in the specific query packet (Available : 1~25 secs) 왏 Router Ports: To set the interface what connect to IGMP Router, and it is the switch what it send/receive IGMP report/leave port. Router ports may be only or more than one. 왏 Apply: To save all configuration. 4.16.3 Snooping Here you can enable the IGMP snooping for certain ports.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN 쮿 Parameter 왏 IGMP Group Membership: To display current built-up multicast group entry. 왏 Previous Page: To display previous page context. 왏 Next Page: To display next page context. 왏 Refresh: To Update multicast group membership.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 4.17.1 Management: Alarm Configuration Events EN 4.17 쮿 Events Configuration The Trap Events Configuration function is used to enable the switch to send out the trap information while pre-defined trap events occurred. The switch offers 22 different trap events to users for switch management. The trap information can be sent out in three ways, including email, mobile phone SMS (short message system) and trap.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 왏 LACP: LACP Disabled, LACP Enabled, LACP Member Added, LACP Port Failure 왏 GVRP: GVRP Disabled, GVRP Enabled EN 왏 VLAN: Port-based VLAN Enabled, Tag-based VLAN Enabled 왏 Module Swap: Module Inserted, Module Removed, Dual Media Swapped 4.17.2 Email 쮿 Email/SMS Configuration Alarm configuration is used to configure the persons who should receive the alarm message via either email or SMS, or both. It depends on your settings.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 쮿 Parameter: 왏 Email: Mail Server: the IP address of the server transferring your email. Username: your username on the mail server. Email Address 1 – 6: email address that would like to receive the alarm message. 왏 SMS: SMS Server: the IP address of the server transferring your SMS. Username: your username in ISP. Password: your username in ISP. Mobile Phone 1-6: the mobile phone number that would like to receive the alarm message. 4.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management 4.18.2 Ping EN 쮿 Ping Test Ping Test function is a tool for detecting if the target device is alive or not through ICMP protocol which abounds with report messages. The switch provides Ping Test function to let you know that if the target device is available or not. You can simply fill in a known IP address and then click button.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management changing VLAN mode configuration, you must reboot to have the new configuration taken in effect. Here we are discussing the software reset for rebooting in the main menu. Firmware upgrade EN 4.19.2 Software upgrade tool is used to help upgrade the software function in order to fix or improve the function. The switch provides a TFTP client for software upgrade. This can be done through Ethernet.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Management: SNMP EN 4.20 Any Network Management System (NMS) running the Simple Network Management Protocol (SNMP) can manage the managed devices equipped with the SNMP agent, provided that the Management Information Base (MIB) is installed correctly on the managed devices.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management Default is Enable. If the SNMP support is deactivated, LANmonitor can not show information about the LANCOM Switch. 왏 Get/Set/Trap Community: Community name is used as password for authenticating if the requesting network management unit belongs to the same community group. If they both don’t have the same community name, they don’t belong to the same group.
LANCOM GS-2124 쮿 Chapter 4: Operation of Web- based Management EN For each public trap, the switch supports the trap event Cold Start, Warm Start, Link Down, Link Up and Authentication Failure Trap. They can be enabled or disabled individually in the menu alarm > events. For the configuration of the traps use the function alarm and events. When enabled, the corresponded trap will actively send a trap message to the trap host when a trap happens.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 5 5.1 Operation of CLI Management CLI Management -- Locate the correct DB-9 null modem cable with female DB-9 connector. Null modem cable comes with the management switch. Refer to the Appendix B for null modem cable configuration. -- Attach the DB-9 female connector to the male DB-9 serial port connector on the Management board. -- Attach the other end of the DB-9 cable to an ASCII terminal emulator or PC Com-1, 2 port.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management Commands of CLI EN 5.2 5.2.1 Global Commands of CLI 쮿 end 왏 Syntax: end 왏 Description: Back to the top mode. When you enter this command, your current position would move to the top mode. If you use this command in the top mode, you are still in the position of the top mode. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(alarm)# events GS-2124L(alarm-events)# end GS-2124L# EN 쮿 exit 왏 Syntax: exit 왏 Description: Back to the previous mode. When you enter this command, your current position would move back to the previous mode. If you use this command in the top mode, you are still in the position of the top mode. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L# ip GS-2124L(ip)# help Commands available: ------------<< Local commands >>-----------set ip EN set dns Set ip,subnet mask and gateway Set dns enable dhcp Enable DHCP, and set dns auto or manual disable dhcp Disable DHCP show Show IP Configuration ------------<< Global commands >>-----------exit Back to the previous mode end Back to the top mode help Show available commands history Show a list of previously run commands logou
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Possible value: [#]: 1, 2, 3, …., 256 왏 Example: GS-2124L(ip)# history Command history: EN 0. trunk 1. exit 2. GS-2124L# trunk 3. GS-2124L(trunk)# exit 4. GS-2124L# 5. ? 6. trunk 7. exit 8. alarm 9. events 10. end 11. ip 12. help 13. ip 14. history GS-2124L(ip)# history 3 Command history: 13. ip 14. history 15.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management When you enter this command via Telnet connection, you would logout the system and disconnect. If you connect the system through direct serial port with RS-232 cable, you would logout the system and be back to the initial login prompt when you run this command. 왏 Argument: None. EN 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Description: To restore the startup configuration as user defined configuration. If restoring default successfully, the CLI would prompt if reboot immediately or not. If you press Y or y, the system would reboot immediately; others would back to the CLI system. After restoring user-defined configuration, all the changes in the startup configuration would be lost. After rebooting, the entire startup configuration would replace as user defined one.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management Saving start... Save Successfully GS-2124L# EN 쮿 save user 왏 Syntax: save user 왏 Description: To save the current configuration as the user-defined configuration. When you enter this command, the CLI would save your current configuration into the non-volatile FLASH as user-defined configuration. 왏 Argument: None. 왏 Possible value: None. 왏 Example: GS-2124L# save user Saving user... Save Successfully GS-2124L# 5.2.2 4-2- 2.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Possible value: : 1 to 24 : 1-10, default is 2 왏 Example: GS-2124L(802.1X)# set maxReq 2 2 EN 쮿 set mode 왏 Syntax: set mode 왏 Description: To set up the 802.1X authentication mode of each port. 왏 Argument: : syntax 1,5-7, available from 1 to 24 : set up 802.1X mode 0:disable the 802.1X function 1:set 802.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 2:Auto 왏 Possible value: : 1 to 24 : 0, 1 or 2 EN 왏 Example: GS-2124L(802.1X)# set port-control 2 2 쮿 set quietPeriod 왏 Syntax: set quietPeriod 왏 Description: A timer used by the Authenticator state machine to define periods of time during when it will not attempt to acquire a Supplicant.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : 1 to 24 < on | off l> : 0 or 1, default is 1 왏 Example: GS-2124L(802.1X)# set reAuthEnabled 2 1 EN 쮿 set reAuthMax 왏 Syntax: set reAuthMax 왏 Description: The number of reauthentication attempts that are permitted before the port becomes Unauthorized. 왏 Argument: : syntax 1,5-7, available from 1 to 24 : max.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 쮿 set serverTimeout 왏 Syntax: set serverTimeout EN 왏 Description: A timer used by the Backend Authentication state machine in order to determine timeout conditions in the exchanges between the Authenticator and the Supplicant or Authentication Server. The initial value of this timer is either suppTimeout or serverTimeout, as determined by the operation of the Backend Authentication state machine.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Description: A timer used by the Backend Authentication state machine in order to determine timeout conditions in the exchanges between the Authenticator and the Supplicant or Authentication Server. The initial value of this timer is either suppTimeout or serverTimeout, as determined by the operation of the Backend Authentication state machine.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management show status 왏 Description: To display the mode of each port. 왏 Argument: None EN 왏 Possible value: None 왏 Example: GS-2124L(802.1X)# show status Port Mode ====== ============ 1 Disable 2 Multi-host 3 Disable 4 Disable 5 Disable 6 Disable 쮿 show port- config 왏 Syntax: show port-config 왏 Description: To display the parameter settings of each port.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management reAuthMax txPeriod :2 : 30 Quiet Period : 60 reAuthEnabled : ON reAuthPeriod : 120 EN max. Request : 2 suppTimeout : 30 serverTimeout : 30 port 2) Mode : Disabled port control : Auto reAuthMax txPeriod :2 : 30 Quiet Period : 60 reAuthEnabled : ON reAuthPeriod : 120 max. Request : 2 suppTimeout : 30 serverTimeout : 30 쮿 show statistics 왏 Syntax: show statistics <#> 왏 Description: To display the statistics of each port.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management show server 왏 Description: Show the Radius server configuration 왏 Argument: None EN 왏 Possible value: None 왏 Example: GS-2124L(802.1X)# show server Authentication Server ________________________________________ IP Address: 192.168.1.1 UDP Port : 1812 Secret Key : Radius Accounting Server _________________________________________ IP Address: 192.168.1.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(account)# add aaaaa Password: Confirm Password: GS-2124L(account)# EN 쮿 del 왏 Syntax: del 왏 Description: To delete an existing account. 왏 Argument: : existing user account 왏 Possible value: None. 왏 Example: GS-2124L(account)# del aaaaa Account aaaaa deleted 쮿 modify 왏 Syntax: modify 왏 Description: To change the username and password of an existing account.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management Username changed successfully. Password changed successfully. 쮿 show 왏 Syntax: show EN 왏 Description: To show system account, including account name and identity. 왏 Argument: None. 왏 Possible value: None. 왏 Example: GS-2124L(account)# show Account Name Identity ----------------- --------------admin guest Administrator guest ° acl 쮿 ace 왏 Syntax: ace 왏 Description: To display the ace configuration.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management vid: any tag_prio: any dmac: any frame type: arp arp type: Request/Reply (opcode): any EN source ip: any destination ip: any ARP flag ARP SMAC Match: any RARP DMAC Match: any IP/Ethernet Length: any IP: any Ethernet: any action: 1 rate limiter: 0 copy port: 0 쮿 action 왏 Syntax: action 왏 Description: To set the access control per port as packet filter action rule.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Example: GS-2124L(acl)# action 5 0 2 2 GS-2124L(acl)# show EN port policy id action rate limiter port copy counter a class map .. .. ¡-¡-. ¡-. 5 1 23 1 permit 0 0 0 24 1 permit 0 0 0 deny ¡2 .. 2 rate limiter rate(pps) ------------ -----------1 1 2 1 3 1 4 1 5 1 ¡-¡- ¡-¡- GS-2124L(acl)# 쮿 delete 왏 Syntax: delete 왏 Description: To delete the ACE ( Access Control Entry) configuration on the switch.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Description: To move the ACE ( Access Control Entry) configuration between index1 and index2.. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management To set access control rule with rate limiter on switch 왏 Argument: : 1-16 : 1,2,4,8,16,32,64,128,256,512,1000,2000, 4000,8000, 16000,32000,64000,128000,256000,512000,1024000 EN 왏 Possible value: : 1-16 : 1,2,4,8,16,32,64,128,256,512,1000,2000, 4000,8000, 16000,32000,64000,128000,256000,512000,1024000 왏 Example: GS-2124L(acl)# ratelimiter 3 16000 GS-2124L(acl)# 쮿 set 왏 Syntax: set [] [] [switch | (port
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management ) | (other ) | (any)] ] EN [] [] [] 왏 Description: To set access control entry on switch 왏 Argument: 왏 Possible value: 왏 Example: 쮿 show 왏 Syntax: show 왏 Description: To show all access control entry setting on switch 왏 Argument: none 왏 Possible value: none 왏 Example: GS-2124L(acl)# show port policy id action ra
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management EN ------------ -----------1 1 2 1 3 1 4 1 5 1 ¡-¡- ¡-¡- GS-2124L(acl)# ° alarm <> 쮿 del mail-address 왏 Syntax: del mail-address <#> 왏 Description: To remove the configuration of E-mail address.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Example: GS-2124L(alarm-email)# del server-user 쮿 set mail-address 왏 Syntax: set mail-address <#> EN 왏 Description: To set up the email address. 왏 Argument: <#> :email address number, range: 1 to 6 :email address 왏 Possible value: <#>: 1 to 6 왏 Example: GS-2124L(alarm-email)# set mail-address 1 abc@mail.abc.com 쮿 set server 왏 Syntax: set server 왏 Description: To set up the IP address of the email server.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Possible value: None. 왏 Example: GS-2124L (alarm-email)# set user admin EN 쮿 show 왏 Syntax: show 왏 Description: To display the configuration of e-mail. 왏 Argument: None. 왏 Possible value: None. 왏 Example: GS-2124L(alarm-email)# show Mail Server : 192.168.1.6 Username : admin Password : **************** Email Address 1: abc@mail.abc.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management :del the range of events, syntax 1,5-7 왏 Possible value: : 1~24 왏 Example: GS-2124L(alarm-events)# del all 1-3 EN 쮿 del email 왏 Syntax: del email 왏 Description: To disable the email of the events. 왏 Argument: :del the range of email, syntax 1,5-7 왏 Possible value: : 1~24 왏 Example: GS-2124L(alarm-events)# del email 1-3 쮿 del trap 왏 Syntax: del trap 왏 Description: To disable the trap of the events.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: :set the range of events, syntax 1,5-7 왏 Possible value: : 1~24 왏 Example: GS-2124L(alarm-events)# set all 1-3 EN 쮿 set email 왏 Syntax: set email 왏 Description: To enable the email of the events. 왏 Argument: :set the range of email, syntax 1,5-7 왏 Possible value: : 1~24 왏 Example: GS-2124L(alarm-events)# set email 1-3 쮿 set trap 왏 Syntax: set trap 왏 Description: To enable the trap of the events.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management To display the configuration of alarm event. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 22 Port-based Vlan Enabled 23 Tag-based Vlan Enabled 24 IP MAC Binding Enabled 25 IP MAC Binding Disabled 26 IP MAC Binding Client Authenticate error EN 27 IP MAC Binding Server Authenticate error 쮿 show (alarm) 왏 Syntax: show 왏 Description: The Show for alarm here is used to display the configuration of Events, or E-mail. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L# autologout 3600 Set autologout time to 3600 seconds ° config- file EN 쮿 export 왏 Syntax: export < ip address> 왏 Description: To run the export function. 왏 Argument: < Usage> set up current or user < ip address> the TFTP server ip address 왏 Possible value: none 왏 Example: GS-2124L(config-file)# export current 192.168.1. 63 Export successful.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management upgrade 왏 Description: To set up the image file that will be upgraded. 왏 Argument: < ip address> : TFTP server ip address : upgrade file path EN 왏 Possible value: < ip address> : TFTP server ip address : upgrade file path 왏 Example: GS-2124L(firmware)# 2124L_v2.03.img upgrade 192.168.2.4 fgs2924R_GS- ° gvrp 쮿 set state 왏 Syntax: set state < 0 | 1> 왏 Description: To disable/ enable the gvrp function.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: : enter which gvrp group you had created, using value is vid.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Description: To set default registrar mode for each port.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 1 20 60 1000 Normal Normal Enable 2 20 60 1000 Normal Normal Enable 3 20 60 1000 Normal Normal Enable 4 20 60 1000 Normal Normal Enable 5 20 60 1000 Normal Normal Enable 6 20 60 1000 Normal Normal Enable 7 20 60 1000 Normal Normal Enable 8 20 60 1000 Normal Normal Enable 9 20 60 1000 Normal Normal Enable 10 20 60 1000 Normal Normal Enable EN ---- --------- ---------- -------------
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : 20 to 100 : 60 to 300 : 1000 to 5000 왏 Example: GS-2124L(gvrp)# set timer 2-8 25 80 2000 EN 쮿 show 왏 Syntax: show 왏 Description: To display the gvrp configuration.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 24 20 60 1000 Normal Normal Disable 쮿 counter 왏 Syntax: counter 왏 Description: To display the counter number of the port.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Description: To show the gvrp group. 왏 Argument: : To set the vlan id from 1 to 4094 왏 Possible value: : 1 to 4094 EN 왏 Example: GS-2124L(gvrp)# group grpinfo 2 GVRP group information VID Member Port ---- ------------------------------------------------° hostname 쮿 hostname 왏 Syntax: hostname 왏 Description: To set up the hostname of the switch. 왏 Argument: : hostname, max. 40 characters.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : syntax 1,5-7, available from 1 to 24 왏 Possible value: : 1 to 24 왏 Example: GS-2124L(igmp)# set drp 1-10 EN 쮿 set erp 왏 Syntax: set erp 왏 Description: Set router ports to enable 왏 Argument: : syntax 1,5-7, available from 1 to 24 왏 Possible value: : 1 to 24 왏 Example: GS-2124L(igmp)# set erp 1 쮿 set flood 왏 Syntax: set flood 왏 Description: To set up disable / enable unregister ipmc flooding.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: None. 왏 Possible value: None. 왏 Example: GS-2124L(igmp)# show gm EN 쮿 show igmpp 왏 Syntax: show igmpp 왏 Description: To display igmp proxy setting 왏 Argument: None. 왏 Possible value: None. 왏 Example: GS-2124L(igmp)# show igmpp ° IP 쮿 disable dhcp 왏 Syntax: disable dhcp 왏 Description: To disable the DHCP function of the system.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management enable dhcp 왏 Description: To enable the system DHCP function and set DNS server via manual or auto mode. 왏 Argument: : set dhcp by using manual or auto mode. EN 왏 Possible value: : manual or auto 왏 Example: GS-2124L(ip)# enable dhcp manual 쮿 set dns 왏 Syntax: set dns 왏 Description: To set the IP address of DNS server. 왏 Argument: : dns ip address 왏 Possible value: 168.95.1.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : 255.255.255.0 or others : 192.168.1.253 or others 왏 Example: GS-2124L(ip)# set ip 192.168.1.2 255.255.255.0 192.168.1.253 EN 쮿 show 왏 Syntax: show 왏 Description: To display the system’s DHCP function state, IP address, subnet mask, default gateway, DNS mode, DNS server IP address and current IP address. 왏 Argument: None 왏 Possible value: None 왏 Example: GS-2124L(ip)# show DHCP : Disable IP Address : 192.168.2.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: < 0 | 1> : 0 : Client , 1: Server : mac address < ip > : ip address < port > : syntax 1,5-7, available from 1 to 24 EN < vid > : vlan id, 1 to 4094 왏 Possible value: < 0 | 1> : 0 : Client , 1: Server : format: 00-02-03-04-05-06 < ip > : ip address < port > : 1 to 24 < vid > : 1 to 4094 왏 Example: GS-2124L(ip_mac_binding)# set entry 1 00-11-2f-de-7b-a9 192.168.2.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: None 왏 Possible value: None EN 왏 Example: GS-2124L(mac-table-alias)# show MAC Alias List MAC Address Alias ----- ----------------- ---------------1) 00-02-03-04-05-06 aaa 2) 00-33-03-04-05-06 ccc 3) 00-44-33-44-55-44 www ° loop-detection 쮿 disable 왏 Syntax: disable <#> 왏 Description: To disable switch ports the loop detection function.
LANCOM GS-2124 3 Disable 3 Normal 4 Disable 4 Normal 5 Disable 5 Normal 6 Disable 6 Normal 7 Disable 7 Normal 8 Disable 8 Normal EN 쮿 Chapter 5: Operation of CLI Management ¡-¡-¡쮿 enable 왏 Syntax: enable <#> 왏 Description: To enable switch ports the loop detection function.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management ¡-¡-¡-¡-. 쮿 Resume 왏 Syntax: resume <#> 왏 Description: To resume locked ports on switch.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: <#> : set up the range of the ports to search for, syntax 1,5-7, available form 1 to 24 왏 Possible value: <#> :1 to 24 EN 왏 Example: GS-2124L (loop-detection)# resume 1-24 GS-2124L (loop-detection)# show Detection Port Port Status Locked Port Port Status --------------------------------1 Enable 1 Normal 2 Enable 2 Normal 3 Enable 3 Normal 4 Enable 4 Normal 5 Enable 5 Normal 6 Enable 6 Normal 7 Enable 7 Normal 8 Enable 8 N
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management Detection Port Port Status Locked Port Port Status EN --------------------------------1 Enable 1 Normal 2 Enable 2 Normal 3 Enable 3 Normal 4 Enable 4 Normal 5 Enable 5 Normal 6 Enable 6 Normal 7 Enable 7 Normal 8 Enable 8 Normal ¡-¡-¡-¡-. ° Mac 쮿 <> 쮿 del 왏 Syntax: del 왏 Description: To del mac alias entry.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 2 23-56-00-55-EF-03 test13 3 23-56-00-55-EF-33 test1 GS-2124L(mac-alias)# del 23-56-00-55-3F-03 GS-2124L(mac-alias)# show MAC Alias MAC Alias EN No =========================================== 1 23-56-00-55-EF-03 test13 2 23-56-00-55-EF-33 test1 쮿 set 왏 Syntax: set < alias> 왏 Description: To set mac alias entry.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management show 왏 Description: To display mac alias entry. 왏 Argument: None EN 왏 Possible value: none 왏 Example: GS-2124L(mac-alias)# show MAC Alias No MAC Alias =========================================== 1 23-56-00-55-3F-03 test3 2 23-56-00-55-EF-03 test13 3 23-56-00-55-EF-33 test1 쮿 <> 쮿 flush 왏 Syntax: flush 왏 Description: To del dynamic mac entry.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 1 Static 1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,1 1 FF-FF-FF-FF-FF-FF 8,19,20,21,22,23,24, 쮿 show 왏 Syntax: show EN 왏 Description: To show all mac table informaion.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(mac-maintenance)# show E api_ai 26/vtss_ Aging Configuration: Enter into sta Age time: 300mode MAC Table Learning EN Port Learning Mode-<< Global commands > 206 2 Auto 3 Auto 4 Auto 5 Auto 6 Auto 7 Auto 8 Auto 9 Auto 10 Auto 11 Auto 12 Auto 13 Auto 14 Auto 15 Auto 16 Auto 17 Auto 18 Auto 19 Auto 20 Auto 21 Auto 22 Auto 23 Auto 24 Auto
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 쮿 set learning 왏 Syntax: set learning 왏 Description: To set mac table learning. EN 왏 Argument: : 1,5-7, available from 1 to 24 : auto learning : disable learning : learn frames are discarded 왏 Possible value: : 1,5-7, available from 1 to 24 : auto learning : disable learning : learn frames are discarded.
LANCOM GS-2124 EN 쮿 Chapter 5: Operation of CLI Management 10 Auto 11 Auto 12 Auto 13 Auto 14 Auto 15 Auto 16 Auto 17 Auto 18 Auto 19 Auto 20 Auto 21 Auto 22 Auto 23 Auto 24 Auto 쮿 show 왏 Syntax: show 왏 Description: To display mac table maintenance 왏 Argument: Noneq 왏 Possible value: None 왏 Example: GS-2124L(mac-maintenance)# show 1 Static Aging Configuration:FF 1,2,3,4,5,6,7,8,9 Age time: 3004,15,16,17,1 MAC Table Learning Port Learning Mode 208
LANCOM GS-2124 2 Auto 3 Auto 4 Auto 5 Auto 6 Auto 7 Auto 8 Auto 9 Auto 10 Auto 11 Auto 12 Auto 13 Auto 14 Auto 15 Auto 16 Auto 17 Auto 18 Auto 19 Auto 20 Auto 21 Auto 22 Auto 23 Auto 24 Auto EN 쮿 Chapter 5: Operation of CLI Management 쮿 <> 쮿 add 왏 Syntax: add [alias] 왏 Description: To add the static mac entry.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : 0-24. The value “0” means this entry is filtering entry : vlan id. 0, 1-4094. VID must be zero if vlan mode is not tag-based [alias] : mac alias name, max. 15 characters 왏 Possible value: : mac address EN : 0-24 : 0, 1-4094 [alias] : mac alias name 왏 Example: GS-2124L(mac-static-mac)# add 00-02-03-04-05-06 3 0 aaa GS-2124L(mac-static-mac)# 쮿 쮿 del 왏 Syntax: del 왏 Description: To del the static mac entry.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: None 왏 Possible value: None EN 왏 Example: GS-2124L(mac-static-mac)# show filter Static Filtering Etnry: (Total 1 item(s)) 1) mac: 00-33-03-04-05-06, vid: -, alias: ccc GS-2124L(mac-static-mac)# 쮿 show forward 왏 Syntax: show forward 왏 Description: To display the static forwarding mac entry.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 1 to 24: available port number 0: disable mirror function 왏 Possible value: <#>: 1 to 24 EN 왏 Example: GS-2124L(mirror)# set mirror 2 쮿 set monitor- destination 왏 Syntax: set monitor-destination 왏 Description: To set monitor destination port. The packets sent by this port will be copied to the monitoring port.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 13 V 14 V 15 V 16 17 EN 18 쮿 set monitor- source 왏 Syntax: set monitor-source 왏 Description: To set up the monitoring port of the mirror function. User can observe the packets that the monitored port received via this port. 왏 Argument: : the monitoring port that is chosen for the mirror function.
LANCOM GS-2124 EN 쮿 Chapter 5: Operation of CLI Management 10 V 11 V 12 V 13 V 14 V 15 V 16 17 18 V 19 20 21 22 23 24 GS-2124L(mirror)# 쮿 show 왏 Syntax: show 왏 Description: To display the setting status of mirror configuration.
LANCOM GS-2124 4 V 5 V 6 V 7 V 8 V 9 V 10 V 11 V 12 V 13 V 14 V 15 V EN 쮿 Chapter 5: Operation of CLI Management 16 17 18 V 19 20 21 22 23 24 GS-2124L(mirror)# ° mstp 쮿 disable 왏 Syntax: disable 왏 Description: To disable mstp function.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Possible value: None 왏 Example: GS-2124L (mstp)# disable EN 쮿 enable 왏 Syntax: enable 왏 Description: To enable mstp function. 왏 Argument: None 왏 Possible value: None 왏 Example: GS-2124L (mstp)# enable 쮿 migrate- check 왏 Syntax: migrate-check 왏 Description: To force the port to transmit RST BPDUs.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management To set max age,forward delay,max hops. 왏 Argument: : available from 6 to 40. Recommended value is 20 : available from 4 to 30. Recommended value is 15 : available from 6 to 40. Recommended value is 20 EN 왏 Possible value: : available from 6 to 40. Recommended value is 20 : available from 4 to 30. Recommended value is 15 : available from 6 to 40.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: 왏 syntax: 1,5-7, available from 1 to 24 : 0, 1-200000000.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 : syntax: 1,5-7, available from 1 to 24 : only 1~2 are valid values 왏 Example: GS-2124L(mstp)# set p-hello 5-10 1 GS-2124L(mstp)# EN 쮿 set p-p2p 왏 Syntax: set p-p2p 왏 Description: To set per port admin p2p 왏 Argument: 왏 syntax: 1,5-7, available from 1 to 24 : Admin point to point, 왏 Possible value: 왏 syntax: 1,5-7, available from 1 to 24
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(mstp)# set priority 0 4096 GS-2124L(mstp)# enable MSTP started GS-2124L(mstp)# show instance 0 mstp status : enabled EN force version : 3 instance id: 0 bridge max age : 20 bridge forward delay : 15 bridge max hops : 20 instance priority : 4096 bridge mac : 00:40:c7:5e:00:09 CIST ROOT PRIORITY : 4096 CIST ROOT MAC : 00:40:c7:5e:00:09 CIST EXTERNAL ROOT PATH COST : 0 CIST ROOT PORT ID : 0 CIST REGIONAL ROOT PRIORITY : 4096 CIST REGIONAL ROOT
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 syntax: 1,5-7, available from 1 to 24 : 0->false,1->True 왏 Possible value: : 1 to 24 : 0->false,1->True EN 왏 Example: GS-2124L(mstp)# set r-role 8-12 1 GS-2124L(mstp)# set r-role 13-16 0 GS-2124L(mstp)# show ports 0 ==== =========== ====== ========= ===== ===== ==Operational== =Restricted= Port Port Status Role Path Cost Pri Hello Edge-Port P2P Role Tcn ==== =========== ====== =========
LANCOM GS-2124 EN 쮿 Chapter 5: Operation of CLI Management 18 DISCARDING dsbl 2000000 128 2/2 V 19 DISCARDING dsbl 2000000 128 2/2 V 20 DISCARDING dsbl 2000000 128 2/2 V 21 DISCARDING dsbl 2000000 128 2/2 V 22 DISCARDING dsbl 2000000 128 2/2 V 23 DISCARDING dsbl 2000000 128 2/2 V 24 DISCARDING dsbl 2000000 128 2/2 V GS-2124L(mstp)# 쮿 set r- tcn 왏 Syntax: set r-tcn 왏 Description: To set per port restricted tcn 왏 Argument: 왏 syntax: 1,5-7, available
LANCOM GS-2124 6 0 128 2 true auto false false 7 0 128 2 true auto false false 8 0 128 2 true auto true false 9 0 128 2 true auto true true 10 0 128 2 true auto true true 11 0 128 2 true auto true false 12 0 128 2 true auto true false 13 0 128 2 true auto false false 14 0 128 2 true auto false true 15 0 128 2 true auto false true 16 0 128 2 true auto false true 17 0 128 2 true auto true true 18 0 128 2 true auto true true 19 0 128 2 true
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(mstp)# show region-info Name : test2 Revision : 0 Instances : 0 GS-2124L(mstp)# EN 쮿 set revision- level 왏 Syntax: set rev 왏 Description: To set mstp revision-level(0~65535) 왏 Argument: :0~65535 왏 Possible value: :0~65535 왏 Example: GS-2124L(mstp)# set revision-level 30000 GS-2124L(mstp)# show region-info Name : test2 Revision : 30000 Instances : 0 GS-2124L(mstp)# 쮿 set version 왏 Syntax: set
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2924(mstp)# set version mstp 쮿 show instance 왏 Syntax: show instance 왏 Description: To show instance status EN 왏 Argument: :0->CIST;1-4095->MSTI 왏 Possible value: :0->CIST;1-4095->MSTI 왏 Example: GS-2124L(mstp)# show instance 0 mstp status : enabled force version : 2 instance id: 0 bridge max age : 20 bridge forward delay : 15 bridge max hops : 20 instance priority : 4096 bridge mac : 00:40:c7:5e:00:09 CIS
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(mstp)# 쮿 show pconf 왏 Syntax: show pconf 왏 Description: To show port configuration EN 왏 Argument: instance-id:0->CIST;1-4095->MSTI 왏 Possible value: :0->CIST;1-4095->MSTI 왏 Example: GS-2124L(mstp)# show pconf 0 set r-role 226 Se 2 0 128 2 true auto false false 3 0 128 2 true auto false true 4 0 128 2 true auto false true 5 0 128 2 true auto false false 6 0 128 2 true auto false false 7
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 20 0 128 2 true auto true true 21 0 128 2 true auto true false 22 0 128 2 true auto true false 23 0 128 2 true auto true false 24 0 128 2 true auto true false EN GS-2124L(mstp)# 쮿 show ports 왏 Syntax: show ports 왏 Description: To show port status 왏 Argument: instance-id:0->CIST;1-4095->MSTI 왏 Possible value: :0->CIST;1-4095->MSTI 왏 Example: GS-2124L(mstp)# show ports 0 쮿 show region- info 왏 Syntax:
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(mstp)# 쮿 show vlan-map 왏 Syntax: show vlan-map 왏 Description: To show vlan mapping of an instance EN 왏 Argument: :0->CIST;1-4095->MSTI 왏 Possible value: :0->CIST;1-4095->MSTI 왏 Example: GS-2124L(mstp)# show vlan-map 0 instance 0 has those vlans : 0-4095 GS-2124L(mstp)# ° policy 쮿 add 왏 Syntax: add [name ] [ip ] [port ] [type ] action 왏 Description: To add a new mana
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 1) Name : george Action : Accept IP Range : 192.168.1.1-192.168.1.90 Access Type : HTTP SNMP Port : 2 3 4 5 8 2) Name : rule1 Action : Deny IP Range : 192.168.2.1-192.168.2.30 Access Type : HTTP TELENT SNMP 3) Name : Mary Action : Deny EN Port : 11 12 13 14 15 IP Range : 192.168.3.1-192.168.3.4 Access Type : Any Port : Any GS-2124L(policy)# 쮿 delete 왏 Syntax: delete 왏 Description: To add a new management policy entry.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(policy)# delete 2 GS-2124L(policy)# show 1) Name : rule1 Action : Deny IP Range : 192.168.4.5-192.168.4.22 Access Type : HTTP TELENT SNMP Port : 2 3 4 5 EN GS-2124L(policy)# 쮿 show 왏 Syntax: show 왏 Description: To show management policy list. 왏 Argument: none 왏 Possible value: none 왏 Example: GS-2124L(policy)# show 1) Name : rule1 Action : Deny IP Range : 192.168.4.5-192.168.4.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management None 왏 Possible value: None 왏 Example: GS-2124L (port)# clear counter EN 쮿 set description 왏 Syntax: set description 왏 Description: To set port description 왏 Argument: syntax : 1,5-7, available from 1 to 24 : set port description, max 47 characters 왏 Possible value: : 1 to 24 : max 47 characters 왏 Example: GS-2124L(port)# set description 3-8 salesdepartment GS-2124L(port
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 쮿 set excessive-collision 왏 Syntax: set excessive-collision 왏 Description: To set port description EN 왏 Argument: syntax : 1,5-7, available from 1 to 24 왏 Possible value: : 1 to 24 왏 Example: GS-2124L(port)# set excessive-collision 6-10 restart GS-2124L(port)# show config Speed/ Flow Maximum Excessive Port Duplex Control Frame Collision Description a list of previously run command set priority
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: : syntax 1,5-7, available from 1 to 24 왏 Possible value: : 1 ~ 24 EN 왏 Example: GS-2124L(port)# set flow-control 3-10 GS-2124L(port)# show config 1 Auto Disabled 9600 Doscard 2 Auto Disabled 9600 Discard 3 Auto Enabled 9600 Discard salesdepartment 4 Auto Enabled 9600 Discard salesdepartment 5 Auto Enabled 9600 Discard salesdepartment 6 Auto Enabled 9600 Restart salesdepartment 7 Auto Enabled 9600 Rest
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(port)# set max-frame 3-6 1518 GS-2124L(port)# show config EN Speed/ Flow Maximum Excessiveommands 2 Auto Disabled 9600 Discard 3 Auto Enabled 1518 Discard salesdepartment 4 Auto Enabled 1518 Discard salesdepartment 5 Auto Enabled 1518 Discard salesdepartment 6 Auto Enabled 1518 Restart salesdepartment 7 Auto Enabled 9600 Restart salesdepartment 8 Auto Enabled 9600 Restart salesdepartment 9 Auto Enabled 9600 Restart 10 Auto
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : auto, 10half, 10full, 100half, 100full, 1Gfull 왏 Example: GS-2124L(port)# set speed 3 auto GS-2124L(port)# show status Speed/ EN Port Link Duplex Rx Pause Tx Pause Description ---- ---- --------- -------- -------- -------------------------------1 Up 100M/Full Disabled Disabled 2 Down Down Disabled Disabled 3 Up 100M/Full Disabled Disabled 4 Down Down Disabled Disabled 5 Down Down Disabled Disabled 6 Down Down Disabled Disabled 7
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 2 1G/Full Disabled 9600 Discard 3 Auto Disabled 9600 Discard 4 1G/Full Disabled 9600 Discard EN 5 1G/Full Disabled 9600 Discard 6 Auto Disabled 9600 Discard 7 Auto Disabled 9600 Discard 8 Auto Disabled 9600 Discard 9 Auto Disabled 9600 Discard 10 Auto Disabled 9600 Discard 11 Auto Disabled 9600 Discard 12 Auto Disabled 9600 Discard 쮿 show detail- counter 왏 Syntax: show detail-counter 왏 Description: To display the display detai
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management Rx 512-1023 Bytes 33 Tx 512-1023 Bytes 144 Rx 1024-1526 Bytes 28 Tx 1024-1526 Bytes 11453 0 Tx 1527- Bytes Receive Error Counters ---------------------------Rx Drops Transmit Error Counters ------------------------------------ 0 Tx Drops Rx CRC/Alignment 0 0 0 Tx Late/Exc. Coll.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management Vendor Rev : 10 Vendor SN : PP220052901281 Date Code : 051012 Temperature : none EN Vcc : none Mon1 (Bias) mA : none Mon2 (TX PWR) : none Mon3 (RX PWR) : none GS-2124L(port)# Port 23 SFP information --------------------------------------------------------------------Connector Type : SFP - LC Fiber Type : Multi-mode (MM) Tx Central Wavelength : 850 Baud Rate : 1G Vendor OUI : 00:40:c7 Vendor Name : APAC Opto Vendor PN : KM28
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management To display the summary counting of each port’s traffic. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(port)# show status Speed/1G/Full Disable Port Link Duplex Rx Pause Tx Pause Description 3 Auto Disabled 9600 Discard 2 Down Down Disabled Disabled EN 3 Up 100M/Full Disabled Disabled 4 Down Down Disabled Disabled 5 Down Down Disabled Disabled 6 Down Down Disabled Disabled 7 Up 1G/Full Disabled Disabled 8 Down Down Disabled Disabled 9 Down Down Disabled Disabled 10 Down Down Disabled Disabled 11 Up Null/Half Disabled Disabled
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management ° qos 쮿 <> 쮿 쮿 set class 왏 Syntax: set class <#> EN 왏 Description: To set number of classes.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : 1 / 2 / 4 / 8 : 1 / 2 / 4 / 8 왏 Possible value: : 1 to 24 : low | normal | medium | high EN : 1 to 24 : 0 to 7 : strict | weighted : 1 / 2 / 4 / 8 : 1 / 2 / 4 / 8 : 1 / 2 / 4 / 8 : 1 / 2 / 4 / 8 왏 Example: GS-2124L(qos-ports)# set port 2 medium 1 3
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 쮿 show 왏 Syntax: show 왏 Description: To show port information.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : ethernet : 0xfff0 : high 왏 Possible value: : dscp field, syntax 1,5-7, available from 0 to 63 EN < tos> : tos priority , available from 1 to 8 < tagpriority> : tag priority, available from 1 to 8 : ethernet : 0xfff0 : high 왏 Example: GS-2124L(qos-qcl)# set 2 0 3 ethernet 0xfff0 high GS-2124L(qos-qcl)# show 2 1 QCE Type: Ethernet Type Ethernet Type Value:0xfff0 Traffic Class: High GS-21
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management GS-2124L(qos-qcl)# move 2 1 1 쮿 delete 왏 Syntax: delete 왏 Description: To delete the specific QCE entry in the specific QCL. EN 왏 Argument: : the qcl number, available from 1 to 24. : 1,5-7, available from 1 to 12 왏 Possible value: : available from 1 to 24.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management rate: allowed values are 500kbps-1Gkps unit: 'k' means kbps and 'm' means mbps shaper enabled: 1 means enable and 0 means disable rate: allowed values are 500kbps-1Gkps unit: 'k' means kbps and 'm' means mbps EN 왏 Example: GS-2124L(qos-rate)# set 2 1 1000 m 1 1000 m GS-2124L(qos-rate)# show 2 V 1000 Mbps V 1000 Mbps 3 500 kbps 500 kbps 4 500 kbps 500 kbps 5 500 kbps 500 kbps 6 500 kbps 500 kbps 7 500 kbps 500 kbps 8 5
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1k, 2k, 4k, 8k, 16k, 32k, 64k, 128k , 256k, 512k 왏 Example: GS-2124L(qos-storm)# set broadcast 1 512 Frame Type EN GS-2124L(qos-storm)# show Status Rate(Packet Per Second) -----------------------------------------------Flooded unicast Multicast Broadcast 1 1 V 512 쮿 set multicast 쮿 왏 Syntax: set multicast 왏 Description: To set multicast storm control configuration 왏 Argument:
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management Flooded unicast Multicast Broadcast V V 1 64 512 EN 쮿 set unicast 쮿 왏 Syntax: set unicast 왏 Description: To set flooded unicast storm control configuration 왏 Argument: : 1 means enable and 0 means disable : 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1k, 2k, 4k, 8k, 16k, 32k, 64k, 128k , 256k, 512k 왏 Possible value: : 1 means enable and 0 means disable : 1, 2, 4, 8, 16, 32, 64, 128, 256, 512, 1k, 2k, 4k,
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management To show storm control configuration 왏 Argument: none 왏 Possible value: none Frame Type EN 왏 Example: GS-2124L(qos-storm)# show Status Rate(Packet Per Second) -----------------------------------------------Flooded unicast V Multicast V Broadcast V 128 64 512 ° reboot 쮿 reboot 왏 Syntax: reboot 왏 Description: To reboot the system. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: None. 왏 Possible value: None. EN 왏 Example: GS-2124L(snmp)# disable snmp GS-2124L(snmp)# disable set-ability 쮿 <> 왏 Syntax: enable set-ability enable snmp 왏 Description: The Enable here is used for the activation snmp or set-community. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management :trap community name 왏 Possible value: <#>: 1 to 6 :1~65535 EN 왏 Example: GS-2124L(snmp)# set get-community public GS-2124L(snmp)# set set-community private GS-2124L(snmp)# set trap 1 192.168.1.1 162 public 쮿 show 왏 Syntax: show 왏 Description: The Show here is to display the configuration of SNMP. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management MCheck 왏 Description: To force the port to transmit RST BPDUs. 왏 Argument: : syntax 1,5-7, available from 1 to 24 EN 왏 Possible value: : 1 to 24 왏 Example: GS-2124L(stp)# Mcheck 1-8 disable 왏 Syntax: disable 왏 Description: To disable the STP function. 왏 Argument: None. 왏 Possible value: None. 왏 Example: GS-2124L(stp)# disable enable 왏 Syntax: enable 왏 Description: To enable the STP function. 왏 Argument: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 쮿 set config 왏 Syntax: set config 왏 Argument: :priority must be a multiple of 4096, available from 0 to 61440. : available from 1 to 10. : available from 6 to 40. : available from 4 to 30. Note: 2*(Forward Delay -1) >= Max Age Max Age >= 2*(Hello Time +1) 왏 Possible value: : 0 to 61440 : 1 to 10
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Possible value: :1 to 24 : 0, 1-200000000 : 0 to 240 : yes / no EN : auto / true / false 왏 Example: GS-2124L(stp)# set port 1-16 0 128 yes auto 쮿 set version 왏 Syntax: set version 왏 Description: To set up the version of STP.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management Bridge Priority (0-61440) : 61440 Hello Time (1-10 sec) :2 Max. Age (6-40 sec) : 20 Forward Delay (4-30 sec) : 15 Force Version : RSTP EN 쮿 show port 왏 Syntax: show port 왏 Description: To display the port information of STP. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 EN 쮿 Chapter 5: Operation of CLI Management 12 DISCARDING 2000000 128 No Auto 13 DISCARDING 2000000 128 No Auto 14 DISCARDING 2000000 128 No Auto 15 DISCARDING 2000000 128 No Auto 16 DISCARDING 2000000 128 No Auto 17 DISCARDING 2000000 128 No Auto 18 DISCARDING 2000000 128 No Auto 19 DISCARDING 2000000 128 No Auto 20 DISCARDING 2000000 128 No Auto 21 DISCARDING 2000000 128 No Auto 22 DISCARDING 2000000 128 No Auto 23 DISCARDING 2000000 128 No Auto 24 DIS
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management :0 Root Path Cost :0 Current Max. Age(sec) : 20 Current Forward Delay(sec) Hello Time(sec) STP Topology Change Count : 15 :2 :0 EN Root Port Time Since Last Topology Change(sec) : 848 ° system 쮿 set contact 왏 Syntax: set contact 왏 Description: To set the contact description of the switch. 왏 Argument: :string length up to 40 characters. 왏 Possible value: : A, b, c, d, ... ,z and 1, 2, 3, …. etc.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 쮿 set location 왏 Syntax: set location 왏 Description: To set the location description of the switch. EN 왏 Argument: : string length up to 40 characters. 왏 Possible value: : A, b, c, d, ... ,z and 1, 2, 3, …. etc. 왏 Example: GS-2124L(system)# set location Taipei 쮿 show 왏 Syntax: show 왏 Description: To display the basic information of the switch. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management Hardware-Mechanical Version : v1.01-v1.01 Serial Number : 030C02000003 Host IP Address : 192.168.1.1 Host MAC Address : 00-40-c7-e7-00-10 : UART * 1, TP * 22, Dual-Media Port(RJ45/SFP) * 2 RAM Size : 16 M Flash Size EN Device Port :2M ° traplog 쮿 clear 왏 Syntax: clear 왏 Description: To clear trap log.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Example: GS-2124L(tftp)# show 2 Mon Mar 17 15:18:38 2008gvrp mode> .
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management HH : (00-23) mm : (01-12) dd : (01-31) hh : (00-23) EN 왏 Example: GS-2124L(time)# set daylightsaving 3 10/12/01 11/12/01 Save Successfully 쮿 set manual 왏 Syntax: set manual 왏 Description: To set up the current time manually.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : -12,-11…,0,1…,13 왏 Example: GS-2124L(time)# set ntp clock.via.net 8 Synchronizing...(1) Synchronization success EN 쮿 show 왏 Syntax: show 왏 Description: To show the time configuration, including “Current Time”, “NTP Server”,” Timezone”, ” Daylight Saving”,” Daylight Saving Start” and “Daylight Saving End” 왏 Argument: None. 왏 Possible value: None. 왏 Example: GS-2124L(time)# show Current Time: Thu Thu 14 15:04:03 2005 NTP Server: 209.81.9.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Argument: : port range, syntax 1,5-7, available from 1 to 24 왏 Possible value: : 1 to 24 왏 Example: GS-2124L(trunk)# del trunk 1 EN 쮿 쮿 set priority 왏 Syntax: set priority 왏 Description: To set up the LACP system priority. 왏 Argument: : available from 1 to 65535.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management active : set the LACP to active mode passive : set the LACP to passive mode 왏 Possible value: : 1 to 24 : static / lacp EN : 1-8. : active /passive 왏 Example: GS-2124L(trunk)# set trunk 1-4 lacp 1 active 쮿 show aggtr- view 왏 Syntax: show aggtr-view 왏 Description: To display the aggregator list. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management To display the detailed information of the LACP trunk group.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Description: To display the aggregator status and the settings of each port. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Description: To delete the port-based vlan group. 왏 Argument: : which vlan group you want to delete. 왏 Possible value: : port-vlan name EN 왏 Example: GS-2124L(vlan)# del port-group VLAN-2 쮿 del tag-group 왏 Syntax: del tag-group 왏 Description: To delete the tag-based vlan group.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Syntax: disable sym-vlan 왏 Description: To drop frames from the non-member port. EN 왏 Argument: : which port(s) you want to set, syntax 1,5-7, available from 1 to 24 왏 Possible value: : 1 to 24 왏 Example: GS-2124L(vlan)# disable sym-vlan 5-10 enable drop-untag 왏 Syntax: enable drop-untag 왏 Description: To drop the untagged frames.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : 1 to 24 왏 Example: GS-2124L(vlan)# enable sym-vlan 5-10 왏 Description: To switch VLAN mode, including disable, port-based, tag-based, metro and double-tag modes.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Example: GS-2124L(vlan)# set port-group VLAN-1 2-5,6,15-13 쮿 set port- role 왏 Syntax: set port-role [vid] EN 왏 Description: To set egress rule: configure the port roles.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management 왏 Example: GS-2124L(vlan)# set pvid 3,5,6-8 5 쮿 set tag- group 왏 Syntax: set tag-group <#> EN 왏 Description: To add or edit the tag-based vlan group. 왏 Argument: : vlan ID, range from 1 to 4094 : tag-vlan name : vlan group members, syntax 1,5-7, available from 1 to 24 <#>: sym/asym vlan setting.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management Sym-vlan : Disable Member : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2) Vlan Name : VLAN-2 Vlan ID : 2 Sym-vlan : Disable EN Member : 2 3 4 5 6 13 14 15 쮿 show port 왏 Syntax: show port 왏 Description: To display pvid, ingress/egress rule. 왏 Argument: None. 왏 Possible value: None.
LANCOM GS-2124 쮿 Chapter 5: Operation of CLI Management : 23 1 Disable Disable Access - 24 1 Disable Disable Access - EN : 273
LANCOM GS-2124 쮿 Chapter 6: Appendix 6 Appendix 6.1 Performance data and specifications EN LANCOM GS-2124 Performance LAN protocols Interfaces Switching technology Store and forward with latency less than 5 μs MAC addresses Support of max 8K MAC addresses Throughput max. 48 Gbps on the backplane Virtual Stacking Management (VSM) Supports stacking of up to 16 devices, several switches can be managed via one ip address VLAN Port based and IEEE 802.
LANCOM GS-2124 쮿 Chapter 6: Appendix 6.2 6.2.1 Connector wiring LAN interface 10/100Base-TX Connector 6.3 Pin Line 1 T+ 2 T- 3 R+ 4 PoE/G 5 PoE/G 6 R- 7 PoE/ -48 V 8 PoE/ -48 V EN 8-pin RJ45 sockets (ISO 8877, EN 60603-7) Declaration of conformity LANCOM Systems herewith declares that the devices of the type described in this documentation are in agreement with the basic requirements and other relevant regulations of the 1995/5/EC directive.
