Datasheet

LTE modem
LTE, UMTS, HSPA, Edge and GPRS supportSupported standards
800/900/1800/2100/2600 MHzLTE-bands
900/2100 MHzUMTS and HSPA bands
850/900/1800/1900 MHzEDGE/GPRS bands
+24 dBmMaximum transmission power UMTS/HSxPA
Receive diversity on the aux antenna (2G + 3G); MIMO (2x2) for LTE (4G)Diversity support
GPS positioning with optional external GPS antenna (accessory)GPS
Firewall
Incoming/Outgoing Traffic inspection based on connection information. Trigger for firewall rules depending on backup status, e.g. simplified rule
sets for low-bandwidth backup lines. Limitation of the number of sessions per remote site (ID)
Stateful inspection firewall
Check based on the header information of an IP packet (IP or MAC source/destination addresses; source/destination ports, DiffServ attribute);
remote-site dependant, direction dependant, bandwidth dependant
Packet filter
Network Address Translation (NAT) based on protocol and WAN address, i.e. to make internal webservers accessible from WANExtended port forwarding
N:N IP address mapping for translation of IP addresses or entire networksN:N IP address mapping
The firewall marks packets with routing tags, e.g. for policy-based routing; Source routing tags for the creation of independent firewall rules for
different ARF contexts
Tagging
Forward, drop, reject, block sender address, close destination port, disconnectActions
Via e-mail, SYSLOG or SNMP trapNotification
Quality of Service
Dynamic bandwidth management with IP traffic shapingTraffic shaping
Dynamic reservation of minimum and maximum bandwidths, totally or connection based, separate settings for send and receive directions. Setting
relative bandwidth limits for QoS in percent
Bandwidth reservation
Priority queuing of packets based on DiffServ/TOS fieldsDiffServ/TOS
Automatic packet-size control by fragmentation or Path Maximum Transmission Unit (PMTU) adjustmentPacket-size control
Automatic or fixed translation of layer-2 priority information (IEEE 802.11p-marked Ethernet frames) to layer-3 DiffServ attributes in routing mode.
Translation from layer 3 to layer 2 with automatic recognition of 802.11p-support in the destination device
Layer 2/Layer 3 tagging
Security
Monitoring and blocking of login attempts and port scansIntrusion Prevention
Source IP address check on all interfaces: only IP addresses belonging to the defined IP networks are allowedIP spoofing
Filtering of IP or MAC addresses and preset protocols for configuration access and LANCAPIAccess control lists
Protection from fragmentation errors and SYN floodingDenial of Service protection
Detailed settings for handling reassembly, PING, stealth mode and AUTH portGeneral
Filtering of unwanted URLs based on DNS hitlists and wildcard filters. Extended functionality with Content Filter OptionURL blocker
Password-protected configuration access can be set for each interfacePassword protection
Alerts via e-mail, SNMP-Traps and SYSLOGAlerts
PAP, CHAP, MS-CHAP and MS-CHAPv2 as PPP authentication mechanismAuthentication mechanisms
Anti-theft ISDN site verification over B or D channel (self-initiated call back and blocking)Anti-theft
Network protection via site verification by GPS positioning, device stops operating if its location is changesGPS anti-theft
Adjustable reset button for 'ignore', 'boot-only' and 'reset-or-boot'Adjustable reset button
High availability / redundancy
VRRP (Virtual Router Redundancy Protocol) for backup in case of failure of a device or remote station. Enables passive standby groups or reciprocal
backup between multiple active devices including load balancing and user definable backup priorities
VRRP
For completely safe software upgrades thanks to two stored firmware versions, incl. test mode for firmware updatesFirmSafe
In case of failure of the main connection, a backup connection is established over ISDN. Automatic return to the main connectionISDN backup
LANCOM 1781-4G
Features as of: LCOS 8.82