TDS

Int/Ext Waterproong Semi-Smooth Flat Paint
Dry-Coat
™
DC-481
Description:
Dry-Coat
TM
is a high performance,
semi-smooth, alkali resistant waterproofing
paint, with sand to create texture, based on a
revolutionary new technology of ultra small
particle size hydrophobic latex design to
waterproof a wide variety of surfaces.
Product Advantages:
• Stops leaks on interior and exterior walls
• Primer + Texture Paint + Sealant
• Heavy metal and lead free
• High in fungicides and algaecide.
• Resists up to 12 PSI of pressure
• UV resistant
• Excellent coverage
• Excellent chalk resistance
Uses:
Dry-Coat™ is ideal to use as a waterproofing
paint or sealant. Waterproofs concrete, brick,
basements, concrete blocks, stucco,
foundations, retaining walls, water ponds,
suitable to use above or below grade.
Notice: The technical data contained herein are
true and accurate to the best of our knowledge.
Published technical data and instructions are
subject to change without prior notice.
S.D.S.: Available upon request.
Surface Preparation:
All surfaces must be dry, clean, sound and free
of contaminants such as dirt, grease, chalk,
mildew, oil, rust, concrete curing agents,
laitance, efflorescence, loose or badly cracked
paint. Remove all contaminants by washing
surfaces with an appropriate cleanser, sanding,
scrapping and/or using a pressure washing
machine. Prime if required, as per
recommended specifications of this product
for surfaces like: concrete, plasters, gypsum
wallboard, drywall, wood, plywood, steel,
aluminum, galvanized steel, other composition
materials or vinyl siding, with the
recommended Lanco
®
primer or primer/sealer,
following application instructions. Glossy
surfaces should be lightly sanded and primed
prior to new paint application. Cracks and holes
have to be clean and dry, with a putty knife
apply Lanco
®
Siliconizer
TM
Crack Filler, into
crack and 2 inches to both sides, patch all holes
with Lanco
®
Spackling Compound. Let dry
thoroughly 24 hours.
Recommended Specications:
Concrete walls as waterproofer:
A total dry film thickness of 12.0 mils of
Dry-Coat™ as an hydrophobic waterproofer
against leaks.
First coat: Dry-Coat™
100-125 ft.
2
/gal. (9-11 m
2
/gal.)
6.7 dry mils, 16.0 wet mils
Second coat: Dry-Coat™
125-150 ft.
2
/gal. (11-13 m
2
/gal.)
5.3 dry mils, 12.8 wet mils
Concrete walls as paint:
A total dry film thickness of 3.4 mils of
Dry-Coat™ as a moisture resistant paint on
surfaces:
First coat: Dry-Coat™
400-450 ft.
2
/gal. (37-41 m
2
/gal.)
1.8 dry mils, 4.0 wet mils
Second coat: Dry-Coat™
400-450 ft.
2
/gal. (37-41 m
2
/gal.)
1.8 dry mils, 4.0 wet mils
MPI: N/A
Green Performance1: No
Green Performance 2: No
VOC Compliant (<100 g/L): Yes
SCAQMD: Passes
AIM & OTC: Passes
Meets Requirements for:
TECHNICAL DATA SHEET
Technical Data:
Method of Application:
Stir thoroughly before using. Paint always on shaded side of the building. Do
not dilute paint, use as supplied. Do not apply when surface or air
temperature is below 50 ˚F (10 ˚C) or if rain is expected within 5 hours. Apply
product with brush, roller or sprayer. Apply generously with a full brush or
roller and avoid excessive brushing or spreading too thinly. Typical standard
practice recommends intermixing when working with more than one
container of the same color, to ensure color consistency.
Mixing and thinning: Mix always thoroughly before application. Thinning is
not recommended, if necessary use only 8oz. of water per gallon of this
product.
Brush: Use a good quality nylon PA-1982 or polyester brush PA-1999.
Roller: Use a Lanco
®
All-Purpose 3/8” Nap Roller PA-566. Apply
generously, but avoid excessive brushing or reworking of painted areas, do
not apply or spread too thinly.
Spray: Spray equipment should be capable of maintaining a pressure of
700-1000 psi with a tip of 0.015 to 0.019. Spray and back roll on rough or
porous surface to achieve required film build. Apply two coats with
overnight drying time between coats, is recommended, to minimize
pinholes on the surface. See equipment’s manufacturer recommendation.
Precaution: Do not add mineral spirits or other solvents to this product. Do
not apply when air or surface temperature is below 50 ˚F (10 ˚C). Apply
liberally,but do not overspread. Stop painting at least two hours before you
expect dew to form or the temperature to fall below 50 ˚F (10 ˚C).
Important: It is important that you apply one coat of primer and two full
coats of paint to achieve the warranty protection.
Limited warranty: The manufacturers liability in connection with the sale of
this product extend only to the replacement price if it should fail to comply
with quality standards or specifications.
Caution: Harmful if swallowed. Contains acrylic resin. In case of eye contact,
flush thoroughly with water. Do not rub eyes. In case of skin contact, flush
area immediately with clean water. If swallowed, do not induce vomiting.
Consult a physician immediately. Use only with adequate ventilation.
Adequate ventilation required when sanding or abrading the dried film.
Always use (NIOSH/MSHA TC21C or equivalent.) Goggles are
recommended while handling the product. This product may contain
chemicals known to the State of California to cause cancer and birth defects
or other reproductive harm. Keep out of reach of children.
Warning! If you scrape, sand, or remove old paint, you may release lead
dust. Lead is toxic. Exposure to lead dust can cause serious illness, such as
brain damage, especially in children. Pregnant women should also avoid
exposure. Wear a NIOSH-approved respirator to control lead exposure.
Clean up carefully with a HEPA vacuum and a wet mop. Before you start,
find out how to protect yourself and your family by contacting the National
Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead. For chemical emergency call ChemTrec
1-800-424-9300. Protect from freezing.
www.lancopaints.com continued on back
Performance:
Product Type: 100% Acrylic
Finish: Flat (1º - 3º)
*Geometry 60º
Solids (%): 61 ± 2% by weight
44 ± 2% by volume
Weight/Gallon: 12.15 ± 0.05 lbs.
( 5.51 ± 0.02 kg.)
Colors: White and tinting bases
Drying Time:
To touch: 1 hr
To recoat: 5 hrs
Coverage As:
Paint: 400-450 ft.
2
/gal.
(37-41 m
2
/gal.) @
1.76 dry mils, 4 wet mils
Waterproofer: 100-125 ft.
2
/gal.
(9-11 m
2
/gal.) @
6.7 dry mils, 16 wet mils
Can Sizes: 5 gallons
1 gallon
Thinning: Is not recommended.
Flash Point: Non-flammable
Viscosity: 105 - 110 KU's
Percent Pigment
by Weight: 45 ± 2%
VOC: 66 g/L
Alkali Resistance: Yes
ASTM D 7705
Efflorescence: Yes
ASTM D7072
Mildew Resistance: Yes
ASTM D3273
Hydrostatic Pressure Resistant:
12PSI