TDS

Page 2
Dry Coat Flat (DC-480)
Rev. 05/2017
• NORTH AMERICA • 600 Mid Florida Drive Airport Industrial Park of Orlando, Florida 32824 • Tel. [phone] Fax [phone]
• CARIBBEAN & SOUTH AMERICA • Urb. Aponte #5, San Lorenzo, Puerto Rico USA 00754 • Tel. [phone] Fax [phone]
•
CENTRAL AMERICA
•
Zona Industrial Bes, lote #4, El Coyol de Alajuela, Costa Rica
•
Tel. [phone] Fax [phone]
Surface Preparation
Surface must be completely dry and in sound condition. All
surfaces must be clean and free of contaminants such as form
and release agents, dirt, grease, oil, rust, chalk, efflorescence,
organic growth, mildew and non-adherent material. Gloss
finishes should be sanded or de-glossed. Feather sand rough
edges and spot prime bare areas. Any deteriorated or failed
sealant and/or patching compound should be removed and
replaced. Fill cracks and voids with Lanco
®
Rain-Shield
TM
Elastomeric Crack Filler. Apply sealants or patching compounds
over a primed surface and at a safe level of pH.
Allow a minimum of three (3) days of cure time for new masonry or
hot stucco, a seven (7) day cure time for poured in place concrete or
a safe pH level below 8.5 prior to application of product. Coatings
have a greater resistance against failure when applied to a surface
with a lower alkaline level (below 8.5). Clean substrate to remove all
form and release agents, dirt, dust, grease and any foreign
contaminants. High pH (between 9 and 13) should be primed with
LANCO
®
Rain-Shield
TM
High pH Primer or LANCO
®
Rain-Shield
TM
Clear
Acrylic Primer/Sealer.
BELOW GRADE OR RETAINING WALLS: Make sure cracks and
holes are clean; dry and free of loose particles. Patch all holes
and cracks using a good quality, fast setting hydraulic cement,
and smooth the patch evenly with the surface around it. Floor
joints where walls and floor meet must be checked for possible
breaks, if necessary fill with a good quality fast setting hydraulic
cement
PREVIOSLY PAINTED SURFACES:
SURFACES IN GOOD CONDITION: Sand any glossy areas by brush
blasting (SSPC-SP 7-63) and dust clean.
SURFACES IN POOR CONDITION: If paint is old, loose, peeling or
badly weathered, repair and clean surface by sanding, brush
blasting (SSPC-SP 7-63) or other methods in order to provide a
sound surface. Apply a full coat of primer as recommended.
MILDEWED SURFACES: Any existing mildew on the surface
must be killed and removed prior to the application of this
product. Any mildew not removed may continue to grow
through the new finish. Using a long-handled brush, scrub
mildewed surfaces with a mixture of one quart of household
bleach and three quarts of warm water. Allow the solution to
remain on the surface for 10 minutes. Rinse thoroughly with
water and allow the surface to dry before painting. Wear
protective eyewear, waterproof gloves, and protective clothing.
Quickly wash off any of the mixture that comes in contact with
your skin. Do not add detergents or ammonia to the bleach /
water solution.
General Information
PRECAUTION: For interior use only. Do not add mineral spirits or
other solvents to this product. Do not apply when surfaces or air
temperature are below 50°F (10°C). Do not expose to freezing
temperatures in storage. Do not use on unpainted ferrous metal.
Do not use on staining wood such as cedar, mahogany, or
redwood.
LIMITED WARRANTY: The manufacturers liability in connection
with the sale of this product extend only to the replacement price
if it should fail to comply with quality standards or specifications.
CAUTION: Harmful if swallowed. Contains Acrylic Resin. In case of
eye contact, flush thoroughly with water. Do not rub eyes. In case
of skin contact, flush area immediately with clean water. If
swallowed, do not induce vomiting. Consult a physician
immediately. Use only with adequate ventilation. Adequate
ventilation required when sanding or abrading the dried film.
Always use NIOSH/MSHA TC21C or equivalent.) Goggles are
recommended while handling the product. Keep out of reach of
children.
WARNING! If you scrape, sand, or remove old paint, you may
release lead dust. Lead is toxic. Exposure to lead dust can cause
serious illness, such as brain damage, especially in children.
Pregnant women should also avoid exposure. Wear a NIOSH-
approved respirator to control lead exposure. Clean up carefully
with a HEPA vacuum and a wet mop. Before you start, find out
how to protect yourself and your family by contacting the
National Lead Information Hotline at 1-800-424-LEAD or log on to
www.epa.gov/lead
. For chemical emergency call ChemTrec 1-800-
424-9300. PROTECT FROM FREEZING.
S.D.S.: Available upon request.
The information presented on this Technical Data Sheet is based on testing
conducted by Lanco
®
Paints &
Coatings. No guarantee of accuracy,
comprehensiveness, or performance is given or implied. Information and
recommendations are subject to change dependent on surface conditions
(substrate), weather and method of application. Please consult with a Lanco
Re
presentative or visit www.lancopaints.com for complete, up-to-
date technical
information.