TDS

Non-Rewettable High Solids Concrete Bonder & Additive
Concrebond Pro 932 CB1053
Description
Concrebond Pro 932 is a modified
liquid polymer with resin composition
and particle size distribution designed
especially for bonding of fresh
concrete, stucco, mortar, or plaster in
patching, plastering and topping
applications. It is easily applied and
bonds tightly to concrete, wood, cinder
block, metal, brick, asphalt and
masonry. Concrebond Pro 932 does not
re-emulsify when exposed to water or
extreme moist conditions.å
Product Advantages
• Dries Transparent
• Excellent bond strength
• Fast drying
• Permanent bond
• Water and humidity resistant
• Meets ASTM C-1059 & ASTM
C-932
• To apply or mix with the plaster
cement
Use
Recommended for difficult applications where
repeated exposure to water may cause
ordinary bonding agents to fail such as in
floors, pavements, curbs, spillways and
sewage plants.
Adheres to porous and non-porous surfaces:
• Wood
• Concrete
• Old or existing plaster
• Wallboard
• Interior roof ceilings
• Lime plaster
Surface Preparation
All surfaces to be bonded must be clean, dry
and free of contaminants such as dust, sand,
oil and grease films.
Product Data
Notice: The technical data contained herein are
true and accurate to the best of our knowledge.
Published technical data and instructions are
subject to change without prior notice.
S.D.S.: Available upon request.
Storage
Protect from freezing; store in a cool, dry place
at room temperature. Product must be used
within one year of purchase.
Mixing:
Always mix thoroughly by hand or with a
power agitator before application.
Cleanup:
Clean all equipment immediately after use with
warm soapy water. Completely flush all spray
equipment with this solution.
Application
For satistactory bonding, follow the procedure:
1. Stir contents of container thoroughly before u
se.
Do not dilute to make volume.
2. Surface should be free of dust, sand or
foreign matter.
3. Apply a uniform coat of Bonding Agent to
the surface by brush, roller or spray gun.
4. Before applying the concrete plaster, check
the surface is clear and with a tacky film.
5. Allow at least two hours to cure before
applying concrete plaster and no more than
24 hours.
6. If cured 24 hours, apply an additional coat
of Bonding before applying concrete plaster.
7. Always maintain the proper level of water in
the concrete plaster mix. Do not apply too dry.
For use as an Admixture:
1. Stir c
ontents of container thoroughly before use.
2. Mix one part CB1053 to three parts of water for
1:3 mix. For optimum results mix one part CB1053 to
one part of water(1:1). Use this mix as the mixing
water for the plaster or cement base coating.
Danger/Warning
Use only with adequate ventilation. Ventilation
must be sufficient to limit exposure below
S.D.S. limits.
Caution:
Do not take internally. Close container after
each use. KEEP OUT OF REACH OF
CHILDREN. Do not take Internally.
For chemical emergency call ChemTrec
1-800-424-9300 (USA) ó 1-703-527-3887
(International).
LIMITATIONS & MORE INFORMATION:
Read Safety Data prior to use.
Go to www.lancopaints.com.
Protect from freezing.
TECHNICAL DATA SHEET
Product Type:
Finish color:
Drying time:
Sizes:
Thinning:
VIscosity:
Flash Point:
Coverage
VOC:
Copolymer Emulsion
White, dries transparent
20-30 minutes
55 gallons
5 gallons
1 gallon
Is not recommended
1900 - 2800 CPS
Non-flammable
250 sq.ft./gal.
23.3 sq.m/gal.)
<50 G/l
www.lancopaints.com
• NORTH AMERICA • 600 Mid Florida Drive Airport Industrial Park of Orlando, Florida 32824 • Tel. [phone] Fax [phone]
• CARIBBEAN & SOUTH AMERICA • Urb. Aponte #5, San Lorenzo, Puerto Rico USA 00754 • Tel. [phone] Fax [phone]
• CENTRAL AMERICA • Zona Industrial Bes, lote #4, El Coyol de Alajuela, Costa Rica • Tel. [phone] Fax [phone]
Rev
. 7 / 2020