User's Manual
Table Of Contents
- 1 Overview and Key Features
- 2 Specification
- 2.1 Specification Summary
- 3 Hardware Specifications
- 3.3.4 OTA (Over-the-Air) smartBASIC Application Download
- 4 Power Consumption
- 5 Functional Description
- 5.1 Power Management (includes Brown-out and Power on Reset)
- 5.2 Clocks and Timers
- 5.3 Memory for smartBASIC Application Code
- 5.4 Radio Frequency (RF)
- 5.5 NFC
- 5.6 UART Interface
- 5.7 SPI Bus
- 5.8 I2C Interface
- 5.9 General Purpose I/O, ADC, PWM and FREQ
- 5.10 nRESET pin
- 5.11 nAutoRUN pin
- 5.12 vSP Command Mode
- 5.13 Two-wire Interface JTAG
- 5.14 BL652 Wakeup
- 5.15 Low Power Modes
- 5.16 Temperature Sensor
- 5.17 Random Number Generator
- 5.18 AES Encryption/Decryption
- 5.19 Optional External Serial (SPI) Flash
- 5.20 Optional External 32.768 kHz crystal
- 5.21 BL652-SA On-board Chip Antenna Characteristics
- 6 Hardware Integration Suggestions
- 7 Mechanical Details
- 8 Application Note for Surface Mount Modules
- 9 FCC and IC Regulatory Statements
- 10 Japan (MIC) Regulatory
- 11 CE Regulatory
- 12 EU Declarations of Conformity
- 13 Ordering Information
- 14 Bluetooth SIG Qualification
BL652
Datasheet
Embedded Wireless Solutions Support Center:
http://ews-support.lairdtech.com
www.lairdtech.com/bluetooth
65
© Copyright 2016 Laird. All Rights Reserved
Americas: +1-800-492-2320
Europe: +44-1628-858-940
Hong Kong: +852 2923 0610
13 ORDERING INFORMATION
BL652-SA-0x
Intelligent BTv4.2 Module featuring smartBASIC (internal antenna)
BL652-SC-0x
Intelligent BTv4.2 Module featuring smartBASIC (IPEX MHF4 connector)
DVK-BL652-SA / SC-0x
Development Kit for each BL652 series module above
General Comments
This is a preliminary datasheet. Please check with Laird for the latest information before commencing a design. If
in doubt, ask.
14 BLUETOOTH SIG QUALIFICATION
Overview
The BL652 module is listed on the Bluetooth SIG website as a qualified End Product.
Design
Name
Owner
Declaration ID
QD ID
Link to listing on the SIG website
BL652
Laird
D031950
87158
TBD
It is a mandatory requirement of the Bluetooth Special Interest Group (SIG) that every product implementing
Bluetooth technology has a Declaration ID. Every Bluetooth design is required to go through the qualification
process, even when referencing a Bluetooth Design that already has its own Declaration ID. The Qualification
Process requires each company to register as a member of the Bluetooth SIG – www.bluetooth.org
The following is a link to the Bluetooth Registration page: https://www.bluetooth.org/login/register/
For each Bluetooth Design it is necessary to purchase a Declaration ID. This can be done before starting the new
qualification, either through invoicing or credit card payment. The fees for the Declaration ID will depend on your
membership status, please refer to the following webpage:
https://www.bluetooth.org/en-us/test-qualification/qualification-overview/fees
For a detailed procedure of how to obtain a new Declaration ID for your design, please refer to the following SIG
document:
https://www.bluetooth.org/DocMan/handlers/DownloadDoc.ashx?doc_id=283698&vId=317486
Qualification Steps When Referencing a Laird End Product Design
To qualify your product when referencing a Laird end-product design, follow these steps:
1. To start a listing, go to: https://www.bluetooth.org/tpg/QLI_SDoc.cfm
Note: A user name and password are required to access this site.
2. In step 1, select the option, New Listing and Reference a Qualified Design.