A Datasheet 60-2230C Version 1.
60-2230C Datasheet REVISION HISTORY Version 1.0 Date TBD Notes Initial Version Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless Approver Andrew Chen 2 © Copyright 2017 Laird.
60-2230C Datasheet CONTENTS 1. Scope 2. 5 Introduction 2.1 5 General Description 5 3. 60-2230C Features Summary 6 4. Specifications 5. WLAN Functional Description 6. Bluetooth Functional Description 16 7. Block Diagram 8. Electrical Characteristics 7 13 17 18 8.1 Absolute Maximum Ratings 18 8.2 Recommended Operating Conditions 18 8.3 DC Electrical Characteristics 8.4 WLAN Radio Receiver Characteristics 19 8.5 WLAN Transmitter Characteristics 18 9.
60-2230C Datasheet 18.1.1 Federal Communication Commission Interference Statement ....................................................... 38 18.1.2 FCC Caution ..................................................................................................................................... 38 18.1.3 Important Note ................................................................................................................................ 39 18.1.4 End Product Labeling ..........................
60-2230C Datasheet 1. SCOPE This document describes key hardware aspects of the Laird 60-2230C M.2 module providing either SDIO or USB2.0 bus interface for WLAN connection and UART/SDIO/USB2.0 for Bluetooth® (including Low Energy or LE) connection. This document is intended to assist device manufacturers and related parties with the integration of this module into their host devices. Data in this document is drawn from the Marvell 88W8997 datasheet issued in April 25, 2016.
0-2230C Datasheet The 60-2230C module also provides a PCM interface for master or slave mode; with the option of an 8-bit or 16bit width size. Pins CON[0], CON[1], and CON[2] are configuration pins (operation mode). Currently, the default mode for the SDIO/UART (WLAN/Bluetooth) interface is 000. 3. FEATURES SUMMARY The Laird 60-2230C device features are described in Table 1.
60-2230C Datasheet Feature Advanced Bluetooth Description Bluetooth 4.
60-2230C Datasheet Feature Description Operating Temperature -30° to 85°C (-22° to 185°F) Operating Humidity 10 to 90% (non-condensing) Storage Temperature -40° to 85°C (-40° to 185°F) Storage Humidity 10 to 90% (non-condensing) Maximum Electrostatic Discharge Conductive 4KV; Air coupled 8KV follow EN61000-4-2 Size 13 mm (length) x 14 mm (width) x 1.
60-2230C Datasheet Feature Description Modulation Table 802.11ac 802.11n BPSK, QPSK, CCK, 16-QAM, 64-QAM, and 256-QAM. HT MCS Index VHT MCS Index Spatial Streams Modulation 0 0 1 BPSK 1/2 1 1 1 QPSK 2 2 1 QPSK 3 3 1 4 4 1 5 5 6 7 20 MHz 40 MHz 80 MHz Coding No SGI SGI No SGI SGI No SGI SGI 6.5 7.2 13.5 15 29.3 32.5 1/2 13 14.4 27 30 58.5 65 3/4 19.5 21.7 40.5 45 87.8 97.5 16-QAM 1/2 26 28.9 54 60 117 130 16-QAM 3/4 39 43.3 81 90 175.
60-2230C Datasheet Feature Description 5 GHz Frequency Bands ETSI 5.15 GHz to 5.35 GHz (Ch 36/40/44/48/52/56/60/64) 5.47 GHz to 5.725 GHz (Ch 100/104/108/112/116/120/124/128/132/136/140/144) FCC 5.15 GHz to 5.35 GHz (Ch 36/40/44/48/52/56/60/64) 5.47 GHz to 5.725 GHz (Ch 100/104/108/112/116/120/124/128/132/136/140/144 5.725 GHz to 5.825 GHz(Ch 149/153/157/161/165) MIC (Japan) 5.15 GHz to 5.35 GHz (Ch 36/40/44/48/52/56/60/64) 5.47 GHz to 5.725 GHz (Ch 100/104/108/112/116/120/124/128/132/136/140/144) KC 5.
60-2230C Datasheet Feature Description Typical Receiver Sensitivity (PER <= 10%) Note: All values nominal, +/-3 dBm. Sensitivity on CH13 (WLAN)/CH78 (BT) will decade up to 46dB. 802.11a: 6 Mbps 54 Mbps -89 dBm -74 dBm 802.11b: 1 Mbps 11 Mbps -95 dBm -90 dBm (PER<8%) 802.11g: 6 Mbps 54 Mbps 802.11n (2.4 GHz) -91 dBm -75 dBm 6.5 Mbps (MCS0;HT20) -91 dBm 65 Mbps (MCS7;HT20) 13.5Mbps(MCS0;HT40) 135Mbps (MCS7;HT40) -73 dBm -85 dBm -70 dBm 802.11n (5 GHz) 6.5 Mbps (MCS0;HT20) 65 Mbps (MCS7;HT20) 13.
60-2230C Datasheet Feature Description Security Standards Wireless Equivalent Privacy (WEP) Wi-Fi Protected Access (WPA) IEEE 802.11i (WPA2) Encryption Wireless Equivalent Privacy (WEP, RC4 Algorithm) Temporal Key Integrity Protocol (TKIP, RC4 Algorithm) Advanced Encryption Standard (AES, Rijndael Algorithm) Encryption Key Provisioning Static (40-bit and 128-bit lengths) Pre-Shared (PSK) Dynamic 802.
60-2230C Datasheet 5. WLAN FUNCTIONAL DESCRIPTION The 60-2230C M2 module is designed based on the 60-SIPT SiP. It is optimized for high-speed, reliable, and lowpower embedded applications. It is integrated with dual-band WLAN (2.4 GHz/5 GHz) and Bluetooth 4.2. Its functionality includes the following: Improved throughput on the link due to frame aggregation, RIFS (reduced inter-frame spacing), and halfguard intervals.
60-2230C Datasheet Feature WLAN Base Band WLAN Security Description 802.11ac 2x2 MU-MIMO (with on-chip Marvell RF radio) Backward compatibility with legacy 802.11 n/a/b/g technology WLAN/Bluetooth LNA sharing PHY rate up to 866.
60-2230C Datasheet Feature WLAN Channel Description Channel frequency supported. Channel 1 2 3 4 5 6 7 8 9 10 11 12 13 20 MHz Freq. Channel (MHz) 2412 36 2417 40 2422 44 2427 48 2432 52 2437 56 2422 60 2447 64 2452 100 2457 104 2462 108 2467 112 2472 116 120 124 128 132 136 140 144 149 153 157 161 165 Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless Freq.
60-2230C Datasheet 6. BLUETOOTH FUNCTIONAL DESCRIPTION The 60-2230C Bluetooth (BT) block is based on the 60-SIPT SiP that already has fully-integrated Bluetooth baseband and radio. Several features and functions are listed in Table 4. Table 4: Bluetooth functions Feature Bluetooth Interface Bluetooth Core functionality Bluetooth Low Energy (BLE) Core functionality Description Voice interface: Hardware support for continual PCM data transmission/reception without processor overhead.
60-2230C Datasheet 7. BLOCK DIAGRAM Figure 1: 60-2230C Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 17 © Copyright 2017 Laird.
60-2230C Datasheet 8. ELECTRICAL CHARACTERISTICS 8.1 Absolute Maximum Ratings Table 5 summarizes the absolute maximum ratings and Table 6 lists the recommended operating conditions for the 60-2230C. Absolute maximum ratings are those values beyond which damage to the device can occur. Functional operation under these conditions, or at any other condition beyond those indicated in the operational sections of this document, is not recommended.
60-2230C Datasheet 8.4 WLAN Radio Receiver Characteristics Table 8 and Table 9 summarize the WLAN 60-2230C receiver characteristics. Table 8: WLAN receiver characteristics for 2.4 GHz signal chain operation Symbol Frx Srf Radj Parameter Receive input frequency range Sensitivity CCK, 1 Mbps CCK, 11 Mbps OFDM, 6 Mbps OFDM, 54 Mbps HT20, MCS0 HT20, MCS7 Adjacent channel rejection OFDM, 6 Mbps OFDM, 54 Mbps HT20, MCS0 HT20, MCS7 Conditions Min 2.412 Typ Max 2.
60-2230C Datasheet 8.5 WLAN Transmitter Characteristics Table 10: WLAN transmitter characteristics for 2.4 GHz per chain operation Symbol Ftx Pout ATx Freq.
60-2230C Datasheet Symbol ATx Parameter 11ac HT80 EVM compliant 11ac HT80 EVM compliant Transmit power accuracy at 25 ℃ Conditions MCS6-8(Ntst=1,2) MCS9(Ntst=1,2) - Min - Typ 12 10 + 2.0 Max Unit dB 18 dBm 16 dBm 18 dBm 16 dBm Typical Current Consumption Single Chain (mA)8 400 330 400 360 Max.
60-2230C Datasheet 9. BLUETOOTH RADIO CHARACTERISTICS Table 11 through Table 14 describe the basic rate transmitter performance, enhanced data transmitter performance, basic rate receiver performance, enhanced rate receiver performance, and current consumption conditions at 25°C. Table 11: Basic rate transmitter performance temperature at 25°C (1.8V) Test Parameter Maximum RF Output Power Frequency Range 20 dB Bandwidth Min 8 2.4 — Typ 10 — 919.5 Max 11 2.
60-2230C Datasheet Table 13: Basic rate receiver performance at 1.8V Test Parameter Sensitivity (1DH5) Maximum Input Carrier-to-Interferer Ratio (C/I) BER ≤ 0.1% Min — Typ –95 Max -92 BT Spec. ≤ –70 Unit dBm dBm BER ≤ 0.1% –20 -10 — ≥ –20 Co-Channel — 10 11 11 C/I (± 1 MHz) — -4 0 0 dB C/I (± 2 MHz) — -45 — –30 dB C/I (± 3 MHz) — -49 — –40 dB –39 -30 - ≥ –39 dBm Maximum Level of Intermodulation Interferers Table 14: Enhanced data rate receiver performance 1.
60-2230C Datasheet 10. SDIO TIMING REQUIREMENTS The 60-2230C SDIO host interface pins are powered from the VIO_SD voltage supply. The SDIO electrical specifications are identical for the 1-bit SDIO and 4-bit SDIO modes. 10.1 SDR12, SDR25, SDR50 Mode (up to 100MHz) (1.8V) Figure 2:SDIO protocol timing Diagram--- SDR12, SDR25, SDR50 modes (up to 100 MHz) (1.8V) Table 16: SDIO timing requirements--- SDR12, SDR25, SDR50 modes (up to 100 MHz) (1.
60-2230C Datasheet 10.2 SDR104 Mode (208MHz) (1.8V) Figure 3: SDIO protocol timing Diagram--- SDR104 modes (up to 208 MHz) (1.8V) Table 17: SDIO timing requirements--- SDR104 modes (up to 208MHz) (1.8V) Note: Over full range of values specified in the Recommended Operating Conditions unless otherwise specified. Symbol fPP TISU TIH TCLK Parameter Clock Frequency Input setup time Input Hold time Clock Time Raise time, Fall time TCR,TCF <0.
60-2230C Datasheet 10.3 DDR50 Mode (50MHz) (1.8V) Figure 4: SDIO CMD timing Diagram--- DDR50 modes (50 MHz) (1.8V) Figure 5: SDIO DAT[3:0] timing Diagram--- DDR50 modes (50 MHz) (1.8V) Note: In DDR50 mode, DAT[3:0] lines are samples on both edges pF the clock (not applicable for CMD line) Table 18: SDIO timing requirements--- DDR50 modes (50MHz) Symbol Clock Parameter Clock time 50MHz (max) between rising edge Rise time, fall time TCR, TCF <4.00ns (max) at 50MHz.
60-2230C Datasheet Symbol Parameter Condition CCARD Input hold time TIH DDR50 CCARD CMD Output (referenced to clock rising and failing edge) Output delay time during data transfer mode DDR50 TODLY CL 30pF (1card) Output hold time TOHLD DDR50 CL≥15pF (1 card) DAT[3:0] Input (referenced to clock rising and failing edges) ≦10pF (1 card) ≦10pF (1 card) ≦ Input setup time DDR50 CCARD Input hold time TIH2X DDR50 CCARD DAT[3:0] Output (referenced to clock rising and failing edges) Output delay time during data
60-2230C Datasheet Symbol Parameter Data fall time TLR Defined from 10% to 90% for raise time and 90% to 10% for fall time Data risel time TLF Defined from 10% to 90% for raise time and 90% to 10% for fall time TLRFM Rise and fall time matching Source jitter total: to next transition *Including frequency tolerance. Timing difference TUDJ1 between the differential data signals. *Defined at crossover point of differential signals Source jitter total: for paired transitions *Including frequency tolerance.
60-2230C Datasheet 11.2 USB FS Driver and Receiver Parameters Notes: Over full range of values specified in the Recommended Operating Conditions unless otherwise specified. The load is 100Ω differential for these parameters, unless other specified. Table 16: USB FS Driver and Receiver Specifications Symbol Parameter BR Baud rate BRPPM Baud rate tolerance Driver Specifications Output signal ended high VOH Defined with 1.425KΩ pull-up resistor to 3.6V Output signal ended low VOL Defined with 1.
60-2230C Datasheet 11.3 USB HS Driver and Receiver Parameters Notes: Over full range of values specified in the Recommended Operating Conditions unless otherwise specified. The load is 100Ω differential for these parameters, unless other specified.
60-2230C Datasheet 12. PCM INTERFACE SPECIFICATIONS Figure 6: PCM Timing Specification – Master Mode Table 18:PCM Timing Specification – Master Mode Symbol FBCLK Duty CycleBCLK TBCLK rise/fall TDO TDISU TDIHO TBF Parameter - Min. 0.4 20 15 - Typ. 2/2.048 0.5 3 - Max. 0.6 15 15 Unit MHz ns ns ns ns ns Figure 7: PCM Timing Specification – Slave Mode Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 31 © Copyright 2017 Laird.
60-2230C Datasheet Table 19: PCM Timing Specification – Slave Mode Symbol FBCLK Duty CycleBCLK TBCLK rise/fall TDO TDISU TDIHO TBFSU TBFHO Parameter - Min. 0.4 15 10 15 10 Typ. 2/2.048 0.5 3 - Max. 0.6 30 - Unit MHz ns ns ns ns ns ns 13. PIN DEFINITIONS Table 20: Pin definitions Name Type 1 2 3 4 5 6 7 GND 3.3V USB_D+ 3.3V USB_DLED1# GND Power I/O Power I/O O,PU - Voltage Ref. 3.3V 3.3V 3.3V - 8 PCM_CLK I/O 1.8V 9 SDIO CLK I,PU 1.8V 10 PCM_SYNC I/O 1.
60-2230C Datasheet N/C I O,WPU I I, PU I Voltage Ref. N/C 1.8V 1.8V 1.8V 1.8V 1.8V N/C UART Serial Data Input Ground UART Request To Send (Active low) PCIe Receive Data-Positive UART Clear To Send (Active low) PCIe Receive Data-Negative If Not Used N/C N/C GND N/C N/C N/C N/C N/C N/C N/C N/C - - Ground GND N/C N/C N/C N/C O 1.8V PCIe Transmit Data-Positive N/C N/C N/C N/C N/C O I/O O,PD I I,PD I 1.8V 1.8V 1.8V 1.8V 1.8V 1.8V N/C N/C GND N/C N/C N/C N/C SUSCLK(32KHz) I,PU 3.
60-2230C Datasheet Pin # 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 N/C Voltage Ref. N/C N/C If Not Used N/C N/C N/C N/C N/C N/C N/C N/C N/C Ground N/C N/C GND N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C N/C - - Ground GND N/C N/C N/C N/C N/C N/C N/C N/C Power - 3.3V module power supply - N/C N/C N/C N/C Power - - 3.3V module power supply Ground Ground Ground GND GND GND Name Type RESERVED/PETn1 ALERT# (I)(0/3.
60-2230C Datasheet 14. MECHANICAL SPECIFICATIONS Module dimensions of 60-2230C are 22mm x 30mm x 3.3mm. Detail drawings are shown in Error! Reference source not found.. Figure 8: Module dimension of 60-2230C Note: The Wi-Fi MAC address is located on the product label. The BT MAC address is always numerically subsequent to the Wi-Fi MAC address. Therefore, the BT MAC address is the Wi-Fi MAC address plus one. 15. MOUNTING The 60-2230C connects to the host via a standard PCI EXPRESS M2 connector.
60-2230C Datasheet Figure 9: Mounting information of the 60-2230C and recommended layout pattern for the stand-off Embedded Wireless Solutions Support Center: http://ews-support.lairdtech.com www.lairdtech.com/wireless 36 © Copyright 2017 Laird.
60-2230C Datasheet 16. RF LAYOUT DESIGN GUIDELINES / PRECAUTIONS The following is a list of RF layout design guidelines and recommendation when installing a Laird radio into your device. Do not run antenna cables directly above or directly below the radio. Do not place any parts or run any high speed digital lines below the radio. If there are other radios or transmitters located on the device (such as a Bluetooth radio), place the devices as far apart from each other as possible.
60-2230C Datasheet 18. FCC AND IC REGULATORY Model 60-2230C US/FCC SQG-602230C CANADA/IC 3147A-602230C The 60-2230C has been designed to pass certification with the antenna listed below. The required antenna impedance is 50 ohms. Table 21: FCC antenna information Peak gain ( dBi ) Model Type Connector Laird MAF94051 Dipole RP-SMA Laird NanoBlade-IP04 PCB Dipole IPEX MHF 2 dBi Laird MAF95310 Mini NanoBlade Flex PCB Dipole IPEX MHF 2.79 dBi 3.
60-2230C Datasheet This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 18.1.3 Important Note Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
60-2230C Datasheet 18.2 Industry Canada 18.2.1 Industry Canada Statement This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: This device may not cause interference; and This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.
60-2230C Datasheet 18.2.
60-2230C Datasheet 18.2.7 Important Note In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. 18.2.
60-2230C Datasheet Type Connector 2400~2483.5MHz 5150~5250MHz 5250~5350MHz 5470~5725MHz 5725~5850MHz Laird/MAF95310 Mini Nano Blade Flex PCB Dipole IPEX MHF 2.79 dBi (2.4 GHz), 3.38 dBi (5 GHz) Laird/NanoBlue-IP04 PCB Dipole IPEX MHF 2 dBi (2.4 GHz only) Isolated Magnetic Dipole IPEX MHF 2.5 dBi (2.390-2.490 GHz), 3.5 dBi (4.900-5.100, 5.150-5.350, 5.70-5.
60-2230C Datasheet Maximum Output Power for Each Frequency TBD Software Version for Testing SW version: P95 20.5 dBm, 5.15-5.25 GHz 20.5 dBm, 5.25-5.35 GHz 20.5 dBm, 5.47-5.725 GHz The minimum distance between the user and/or any bystander and the radiating structure of the transmitter is 20 cm. 5150 ~ 5350 MHz is limited to indoor used in the following countries: BE DK IE FR CY BG CZ LU NL PT DE EL HR EE ES IT SK UK NO LV HU AT RO FI LI TR LT MT PL SI SE IS CH 20.
60-2230C Datasheet Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Aršo[name of manufacturer /izgatavotājanosaukums] deklarē, ka[type of equipment / iekārtas tips]atbilstDirektīvas 1999/5/EK būtiskajāmprasībām un citiemar to saistītajiemnoteikumiem.
