Warranty Guide

DeMore’s Innovative Design, Inc.
herewith guarantees the structural
integrity of the Ladder Tool Bin
®
product, for one year and warrants it
against all manufacturer defects. This
Warranty is not applicable to any
damage caused by user or caused
by use other than its intended
purpose on step ladders.
Replacement subject to approval by
DeMore’s Innovative Design, Inc.
Upon approval, the Ladder Tool Bin
®
will be replaced free-of-charge.
Call DeMore's Innovative Design, Inc.
for assistance at: 262-825-6784
Thank You for putting your trust
in the Tool Bin Man
®
and
choosing the Ladder Tool Bin
®
.
www.laddertoolbin.com
1) Read all warnings on this product and on
the ladders where this product is being used.
2) Remove the warranty card and keep in a safe
place for your records. (Warranty card includes
warranty, instructions and Warning label.)
3) Orientation of Ladder Tool Bin is based on
verbiage legibility and the handle opening
facing the back of the step ladder...!
4) Remove the provided 9" safety bolt before
setting the Ladder Tool Bin on top of a step
ladder and re-insert prior to using your Ladder Tool Bin.
(See warning note highlighted in the warning label on back.)
5) Paint can holder should accept most 1-gallon paint cans. Snug enough to
avoid accidental spills...!
6) Do not expose the Ladder Tool Bin to temperatures exceeding 210°F…!
7) You’re ready to use & enjoy the convenience of your new Ladder Tool Bin…!
1 Year Warranty
INSTRUCTIONS for Model LTB-1317
DeMore's Innovative Design, Inc.
Made in the USAU.S. Patent No. D838.387
200414 LTB-1317 Insert Card
9" Safety
Bolt
Verbiage
Nylon
Locking
Wing Nut
200414 Copyright © 2020 DeMore's Innovative Design, Inc., Milwaukee, WI. All Rights Reserved.
Always use caution when using the Ladder Tool
Bin
®
...!
The Ladder Tool Bin is intended solely to store (a
reasonable amount of) tools & hardware associated
with work that typically occurs on fiberglass step
ladders and some wood step ladders...!
(Ladder top sizes
for the Ladder Tool Bin range from 5
1
/2"- 7" X 13"- 14
1
/2".)
Warning...! The 9" safety bolt and nylon wing nut
must be used at all times when using the Ladder
Tool Bin...!
(See warning on the back of the Ladder Tool Bin Highlighted below)
“Warning! Must use supplied 9" safety bolt” - “Park here when not in use”
Do not close the step ladder without doing the
following: Be sure the 9" safety bolt is secure in its
designated location - Remove all contents in and on
the Ladder Tool Bin.
An empty Ladder Tool Bin can remain attached to a
closed ladder for storage. NOTE! The 9" safety bolt
must remain in its designated location for this to
apply.
Do not stand on or in the Ladder Tool Bin.
Orientation of Ladder Tool Bin is based on verbiage
legibility and the handle opening facing the back of
the step ladder...!
Thank you for putting your trust in the Tool Bin Man
®
and choosing the Ladder Tool Bin
®
...!
Soyez prudent lorsque vous utilisez le Ladder Tool
Bin
®
… !
Le Ladder Tool Bin est destiné exclusivement à stocker
(une quantité raisonnable) des outils et du matériel
associés aux travaux qui se font généralement sur des
échelles en fibre de verre et quelques échelles en bois...!
(Les tailles supérieures pour le Ladder Tool Bin vont de
5
1
/2
pouces - 7 pouces X 13 pouces -
14
1
/2"
pouces.)
Attention… ! Le boulon de sécurité de 9 pouces et l'écrou
à ailettes en nylon doivent être utilisés en tout temps lors
de l'utilisation du Ladder Tool Bin... !
(Voir l'avertissement à l'arrière du Ladder Tool Bin mis en évidence
ci-dessous)
« Attention ! Vous devez utiliser le boulon de sécurité de 9 pouces
fourni » – « Laissez ici quand elle n'est pas utilisée ».
Ne fermez pas l'escabeau sans faire ce qui suit : Assurez
-vous que le boulon de sécurité de 9 pouces est sécurisé
dans son emplacement désigné - Retirez tous les
contenus dans et sur le Ladder Tool Bin.
Un Ladder Tool Bin vide peut rester attaché à une échelle
fermée pour le stockage. REMARQUE ! Le boulon de
sécurité de 9 pouces doit rester dans son emplacement
désigné pour que cela s'applique.
Ne vous mettez pas debout sur ou dans le Ladder Tool
Bin... !
L'orientation du Ladder Tool Bin est basée sur la lisibilité
du verbiage et l'ouverture de la poignée face à l'arrière
de l'escabeau... !
¡Siempre tenga cuidado al usar el Ladder Tool Bin
®
…!
¡El Ladder Tool Bin está diseñado exclusivamente para
almacenar (Una cantidad reasonable de) herramientas
y equipos asociados con el trabajo que típicamente
ocurre sobre escaleras de fibra de vidrio y algunas
escaleras de madera…!
(Las medidas de la parte superior de la
escalera para el Ladder Tool Bin deben estar en un rango entre
5
1
/2"
a
7"
X
13"
a
14
1
/2".
)
¡ADVERTENCIA…! ¡El perno de seguridad de 9" y la
tuerca de mariposa de nylon deben ser usados en todo
momento mientras se usa el Ladder Tool Bin…!
(Vea las advertencias en la parte trasera del Ladder Tool Bin Resaltadas
a continuación)
“¡Advertencia! Debe usar el pernode seguridad de 9" suministrado” –
“Colocar aquí cuando no esté en uso”
No cierre la escalera sin hacer lo siguiente: Asegúrese
de que el perno de seguridad de 9" esté seguro en su
ubicación designada - Retire todo el contenido dentro
del Ladder Tool Bin.
Un Ladder Tool Bin vacío puede permanecer unido a
una escalera cerrada para su almacenamiento. ¡NOTA!
El perno de seguridad de 9" debe permanecer en el
lugar designado para que esto aplique.
No se pare sobre o dentro del Ladder Tool Bin.
¡La orientación del Ladder Tool Bin está basada en un
lenguaje legible y la agarradera abierta viendo la parte
trasera de la escalera…!
Merci d'avoir confiance en le Tool Bin Man
®
et de choisir le Ladder Tool Bin
®
... !
¡Gracias por poner su confianza en el Tool Bin Man
®
y escoger el Ladder Tool Bin
®
…!

Summary of content (1 pages)