Owner's Manual
Table Of Contents
- 1 Introduction
- 2 Quick Start
- 2.1 Setting Up the Equipment
- 2.2 Gathering Supplies and Equipment
- 2.3 Preparing the Urocap NXT
- 2.4 Preparing the NXT Go Pump Hub
- 2.5 Preparing the Roam NXT
- 2.6 Preparing the UPP Puller NXT (Optional)
- 2.7 Setting Up Consumables and Preparing the Patient
- 3 How to Perform a Study
- 4 Synergy Software
- 5 Maintenance and Service
- 5.1 Cleaning and Disinfection
- 5.2 Preventive Maintenance
- 5.3 Verifying Calibration
- 5.4 Configuration
- 5.5 Computer Virus Protection
- 5.6 Disposing of Product After Use
- 5.7 Environmental Consideration of Waste Disposal
- 5.8 Backups
- 5.9 Troubleshooting Guide
- 6 Hardware
- 7 Appendix
Quick Start
NXT Go Owner’s Manual, LBL-00145, MAN2030 18
Quick Start
To prepare for a typical study, follow the steps provided below.
Setting Up the Equipment
Gathering Supplies and Equipment
Preparing the Urocap NXT
Preparing the NXT Go Pump Hub
Preparing the Roam NXT
Preparing the UPP Puller NXT
Setting Up Consumables and Preparing the Patient
2.1 Setting Up the Equipment
Unpack the NXT Go Pump Hub, Roam NXT, Patient Interface Module NXT (PIM
NXT), and Urocap NXT from their shipping boxes. Unpack the UPP Puller NXT. For
information on the NXT Go Pump Hub, Roam NXT, PIM NXT, Urocap NXT, NXT
Infusion Hook, Remote NXT, or UPP Puller NXT refer to the Hardware section on
page 96.
IMPORTANT: Lock all wheels of the pole or table used for equipment setup. Ensure all
wheels are locked during testing procedures to prevent injury to the patient.
If utilizing the UPP Puller NXT assemble and mount the UPP Puller NXT according
to the instructions provided in the Preparing the UPP Puller NXT section on page
22. For information on charging the UPP Puller NXT refer to the UPP Puller NXT –
Charging the Battery section on page 107.
Connect the PIM NXT to the Roam NXT. For instructions on how to connect these
devices, refer to the Replacing the PIM NXT section on page 102.
Connect the Roam NXT and the Urocap NXT to the PC using the NXT Magnetic
Pogo Pin Cable and the USB to Binder Cable Adapter to pair the devices. Once
paired unplug the devices for wireless use.
Hang the NXT Go Infusion Hook on an IV Pole. Connect the NXT Go Infusion Hook
to the NXT Go Pump Hub. Connect the NXT Go Power Cord to the NXT Go Pump
Hub and the NXT Go Power Supply, then connect to supply mains. Use the NXT
Go USB Cable to connect the NXT Go Pump Hub to the laptop PC. Refer to Figure
77 for a visual of inputs on the NXT Go Pump Hub.
For information on the NXT Go Pump Hub, refer to the NXT Go Pump Hub section on
page 98. For information on charging the Roam NXT, refer to the Roam NXT—
Charging the Battery section on page 103. For information on charging the Urocap
NXT, refer to the Urocap NXT—Charging the Battery section on page 106.
Refer to the Maintenance and Service section on page 75 for information on cleaning
and maintaining the modules, including all system check intervals and procedures for
verifying the integrity of the system.
Turn on the laptop PC by pressing the power button . Double click the
Synergy Icon to launch the Synergy Login Page.
Status DRAFT Effective