User’s Manual Purifier® CELL Series Biological Safety Cabinets Models 34309 Series 34409 Series 34509 Series 34609 Series To receive important product updates, complete your product registration card online at register.labconco.com TYPE A2 Labconco Corporation 8811 Prospect Avenue Kansas City, MO 64132-2696 800-821-5525, 816-333-8811 FAX 816-363-0130 E-MAIL labconco@labconco.com HOME PAGE www.labconco.com Please read the User’s Manual before operating the equipment.
Copyright © 2009 Labconco Corporation. All rights reserved. The information contained in this manual and the accompanying products are copyrighted and all rights reserved by Labconco Corporation. Labconco Corporation reserves the right to make periodic design changes without obligation to notify any person or entity of such change. Warranty Labconco provides a warranty on all parts and factory workmanship.
TABLE OF CONTENTS CHAPTER 1: INTRODUCTION 1 CHAPTER 2: PREREQUISITES Space Requirements Clearance Location Requirements Exhaust Requirements Electrical Requirements Service Line Requirements User-Supplied Microscope Requirements User-Supplied Circulator Requirements 2 2 2 3 4 4 5 5 6 CHAPTER 3: GETTING STARTED Unpacking the Biosafety Cabinet Moving the Cabinet Preparing the Biosafety Cabinet for Operation Installing the Biosafety Cabinet on an Existing Work Surface Installing the Cabinet on a Labconco B
Ultraviolet (UV) Lamp Scope-Ready Package Option Temp-Zone Package Option Safety Precautions 24 25 25 26 CHAPTER 5: USING THE CABINET System Reset Switch Information Center Status Area Data Area Icon Area Operating the Sliding Sash Starting the Biosafety Cabinet The Logic Touchpad User Selectable Features Timer Operation Interval Timer Operation Stopwatch Timer Operation Menu Options UV Lamp Operation UV Lamp Timer UV Lamp Maintenance Light Operation Light Timer Light Maintenance Blower Operation Cabinet
APPENDIX B: DIMENSIONS 59 APPENDIX C: SPECIFICATIONS Electrical Data Motor Specifications Environmental Conditions 61 61 61 62 APPENDIX D: ACCESSORIES Telescoping Base Stands Telescoping Base Stand Shelf Kit Manual or Electric Hydraulic Lift Base Stands Hydraulic Base Stand Shelf Kit SoLo Electric Hydraulic Lift Base Stands Seismic Bracket Kit Service Valve Kit Ultraviolet Lamp Kits IV Bar Kits Shelf Cord/Tubing Management System Prefilter Postfilter Postfilter Conversion Kit Canopy Connection Kit Air-T
Chapter 1: Introduction Congratulations on the purchase of a Labconco Purifier® Cell Logic® Biosafety Cabinet. The Biosafety Cabinet is designed to protect you, the product and the laboratory environment from biohazardous aerosols. The Cell Logic Series Cabinet is the result of users like you requiring a customer supplied microscope integrated into the cabinet and a temperature controlled work area to maintain sample temperature.
Chapter 2: Prerequisites Before you install the Biosafety Cabinet, you need to prepare the site for installation. Examine the location where you intend to install the cabinet. You must be certain that the area is level and of solid construction. In addition, a dedicated source of electrical power must be located near the installation site. Carefully read this chapter to learn: • Location requirements. • Electrical power requirements. • Exhaust requirements. • Service utility requirements.
Chapter 2: Prerequisites Location Requirements Note: The Biosafety Cabinet should be located away from traffic patterns, doors, fans, ventilation registers, fume hoods and any other air-handling devices that could disrupt its airflow patterns. All windows in the room should remain closed. Figure 2-1 shows the preferred location for the Biosafety Cabinet.
Chapter 2: Prerequisites Exhaust Requirements If you intend to connect the Biosafety Cabinet to the optional Canopy Connection Kit, first examine the location to ensure that it accommodates the cabinet’s exhaust duct. The area directly above the cabinet’s exhaust port should be clear of structural elements, water and utility lines, or other fixed obstructions. There should be enough clearance to accommodate a 10-inch diameter duct.
Chapter 2: Prerequisites Service Line Requirements All utility service lines should be ¼ inch O.D., brass, copper, or stainless steel, and equipped with an easily accessible shut-off valve. If the service line pressure exceeds 100 PSI, it must be equipped with a pressure regulator to reduce the line pressure. Note: The use of flammable gases or solvents should be avoided in the Biosafety Cabinet. Open flame in the cabinet will disrupt the laminar airflow in the cabinet and may damage the HEPA filters.
Chapter 2: Prerequisites User Supplied Circulator Requirements – Purifier Cell Logic Biosafety Cabinets with Temp Zone™ Package Only The Temp Zone™ features a temperature controlled area on the work surface where heated or chilled samples may be transferred and kept at optimum temperature. A user-supplied circulator that continually delivers heated or chilled water at a minimum flow rate of 0.5 GPM (1.9 LPM) with typical volume of 6 liters is required and may be obtained from your laboratory supply dealer.
Chapter 3: Getting Started Now that the installation is properly prepared, you are ready to inspect, install, and certify the Purifier Biosafety Cabinet. This chapter covers how to: • Unpack and move the Biosafety Cabinet. • Install the cabinet. • Connect the electrical supply source. • Connect the service lines. • Connect to an exhaust system (optional). • Arrange certification of the Biosafety Cabinet. • Install the microscope (optional – Scope-Ready package only).
Chapter 3: Getting Started Unpacking the Biosafety Cabinet Carefully remove the outer carton and inspect the cabinet for damage that may have occurred in transit. If the Biosafety Cabinet is damaged, notify the delivery carrier immediately and retain the entire shipment intact for inspection by the carrier. Note: United States Interstate Commerce Commission rules require that claims be filed with the delivery carrier within fifteen (15) days of delivery.
Chapter 3: Getting Started Preparing the Biosafety Cabinet for Operation Installation instructions for the cabinet (Labconco P/N 1056801) are attached to the sash of the Biosafety Cabinet. If these instructions are missing or unclear, contact Product Service at 800-821-5525 or 816-333-8811. Installing the Biosafety Cabinet on an Existing Work Surface Note: The Biosafety Cabinet is very top heavy. Use caution when lifting or moving it.
Chapter 3: Getting Started 2. Select the height of the stand and slide four (4) leg extensions into base stand corner posts and attach with 2 ¼ inch long bolt, flatwasher, lockwasher and nut. Ensure that the same height hole is selected for each leg. Tighten the leg bolts securely. See Figure 3-1. Figure 3-1 3. CAUTION: Only lift and support the weight of the cabinet at the stainless steel sides and back. Damage will occur if lifted or supported on the front edge.
Chapter 3: Getting Started Manual or Electric Hydraulic Lift Base Stands These base stands offer infinitely adjustable height between 25.5 and 33.5 inches (648 to 851 mm), giving a Cabinet work surface height of 28.0 to 36.0 inches. The height is adjusted either by a manual (hand crank) or electric pump that drives hydraulic rams in the legs of the stands. All of the hydraulic stands are equipped with fixed feet, but can be converted to caster wheels with the addition of Caster Kit #3784000.
Chapter 3: Getting Started 5. Tighten the tube fitting nut hand tight and then, using a 7/16-inch wrench, tighten it at least ¾ turn more. 6. Close the service valve in the Biosafety Cabinet and then slowly open the shutoff valve on the service valve. Test all fittings for leakage. Tighten the tube nut slightly if needed.
Chapter 3: Getting Started Drain Valve Installation In order to prevent damage during shipping, the drain valve assembly has not been installed. If desired, the valve should be installed after the Cabinet is in its final location. To install the valve assembly, follow these steps: Note: The work surface is heavy. Use caution when handling it. 1. Lift the work surface out of the Biosafety Cabinet by lifting on the knobs at the front of the work surface.
Chapter 3: Getting Started Microscope Installation (optional) In order to successfully install a user-supplied microscope in a Cell Logic Biosafety Cabinet with Scope-Ready package, please follow the steps below and refer to Figure 3-5 as well as Appendix F: Installation Guide for all Pure-Vu Seals and Stand-Still Isolation Platforms: Note: The work surface is heavy. Use caution when handling it. 1.
Chapter 3: Getting Started 9. Finally, re-install the microscope eyepieces. 10. The Pure-Vu Seal should now provide an optimum seal for safe airflow and ergonomic visibility.
Chapter 3: Getting Started Circulator Installation (optional) In order to successfully install a user-supplied circulator on a Cell Logic Biosafety Cabinet with Temp-Zone package please follow the steps below and refer to Figure 3-6: Note: The work surface is heavy and two Easy-Clean™ Prop Rods are provided to pivot and support the Temp-Zone work area and the work surface. 1. The Temp-Zone work area has supply and return lines for the usersupplied circulator.
Chapter 3: Getting Started temperatures than the desired sample temperature. Experimentation is necessary to achieve proper sample temperatures. 10. For chilled applications, the Temp-Zone work area comes with a drain line installed that can be routed to the cabinet’s drain valve, if desired. This Temp-Zone drain line installation is optional for chilled applications should excessive condensation occur under the work surface.
Chapter 3: Getting Started Initial Certification Prior to use, a qualified certifier should certify all Biosafety Cabinets. Under normal operating conditions, the Biosafety Cabinet should be recertified at least annually and when relocated or serviced.
Chapter 4: Performance Features and Safety Precautions All Purifier Series Cell Logic Biosafety Cabinets operate using the following principles: • Filtration and retention of particulates by High Efficiency Particulate Air (HEPA) filter(s) • Laminar airflow • Directional airflow The major components in a Biosafety Cabinet are: • The HEPA filter(s) or optional ULPA filters • The motor/blower to force air through the Cabinet • Cabinet air intakes (grilles), ductwork and air balance controls The tw
Chapter 4: Performance Features and Safety Precautions The HEPA filter manufacturer establishes the efficiency of the filter by challenging it with an aerosol of known particle size. The number of particles that penetrate the filter are quantified, and this establishes the efficiency of the filter. Thus, the filters used in the Purifier Cell logic Biosafety Cabinets are at least 99.99% efficient in removing particles 0.3 micron. Note: The HEPA filter media is very fragile. DO NOT touch the media.
Chapter 4: Performance Features and Safety Precautions Laminar Airflow Laminar airflow is defined as the movement of a body of air in a single direction, with a uniform velocity. In practice, the laminar downflow of air in the cabinet captures any aerosol generated in the work area of the cabinet, and directs it to the HEPA filters. In order to be true laminar downflow, a number of individual downflow velocity test points (The Downflow Velocity Profile) must be +/- 16 feet per minute (0.
Chapter 4: Performance Features and Safety Precautions Directional Airflow Directional airflow also plays a key role in biosafety cabinet performance. Air is drawn into the front of the cabinet at the front grille. This “curtain” of air makes it more difficult for aerosols to escape out of the work area of the cabinet and into the outside environment. This airflow is often calculated and referred to as the Inflow Volume or Average Inflow Velocity. This is illustrated in Figure 4-3.
Chapter 4: Performance Features and Safety Precautions Motor/Blower The motor/blower assembly pulls room air into the front of the cabinet, and re-circulates it internally. During its recirculation, the air is split into two separate streams. One path leads through the exhaust HEPA filter and out of the unit. The second path flows through the supply HEPA filter, which then flows down through the work area, as shown in Figure 4-4.
Chapter 4: Performance Features and Safety Precautions Cabinet Air Intakes (Grilles), Ductwork and Air Balance Controls The location, size, and pattern of the grilles at the front and rear of the work area affect cabinet containment and performance. Note: Never block or obstruct the grilles of the Biosafety Cabinet. The internal ductwork of the Biosafety Cabinet conveys the air from the work area to the blower, and then from the blower to the filters.
Chapter 4: Performance Features and Safety Precautions Note: UV irradiation is absorbed by the tempered safety glass of the sash. Independent research has shown that the level of UV irradiation on the outside of the cabinet’s sash is equal to background radiation levels. Note: The UV sensitivity of a target organism varies, depending on the UV output of the lamp, the genus and species of the organism, the medium the agent is suspended in, etc.
Chapter 4: Performance Features and Safety Precautions circulator chilled to 3.7°C. Actual set points will vary depending on variables such as sample tube rack, sample size, and length of tubing. Safety Precautions WARNING: The Biosafety Cabinet Biohazard Cabinet should be certified by a certification technician before its initial use. The cabinet should be recertified whenever it is relocated, serviced or at least annually thereafter.
Chapter 4: Performance Features and Safety Precautions operating time and the nature of work being done in the cabinet. The Filter Gauge accurately displays the amount of filter life remaining. Proper operation of the cabinet depends largely upon its location and the operator’s work habits. Consult the Installation and Normal Operation sections of this manual for further details. Avoid direct exposure of plastic or coated materials to ultraviolet (UV) radiation.
Chapter 5: Using the Cabinet System Reset Switch The Biosafety Cabinet has a system reset switch for resetting its microprocessors. The switch is located on the front of the electronics module, on top of the Cabinet, as shown in Figure 5-1. Ensure that the switch is in the “ON” (up) position before attempting to operate the Cabinet.
Chapter 5: Using The Cabinet Information Center The Information Center is an LCD display located on the right side wall at eye level. The center’s display is divided into three separate areas, as shown in Figure 5-2, below. The display will turn itself off one minute after the blower is turned off or the sash is closed. Figure 5-2 Status Area Data Area Icon Area Status Area The Status Area displays the system’s condition during operation.
Chapter 5: Using The Cabinet Sash is too high The sash is open too far for safe operation. Airflow Alert The airflow patterns in the cabinet have changed, resulting in a sudden change in the motor speed. This is most likely due to a blockage of the grille or the exhaust filter outlet. It may also be caused by removal of the work surface while the cabinet is in operation. System Error The motor and display circuit board are not communicating properly.
Chapter 5: Using The Cabinet Fluorescent light In this mode the fluorescent lights are operating. When the sash is fully closed, the fluorescent lights automatically turn off. UV light In this mode the UV (germicidal) light is operating. When the sash is fully closed, the UV light can be programmed to automatically turn on. When the sash is raised, the light automatically turns off, to protect the laboratory from UV irradiation.
Chapter 5: Using The Cabinet Starting the Biosafety Cabinet 1. To start the Biosafety Cabinet, raise the sash until its bottom edge aligns with the sash position label on the left corner post. The decal is shown in Figure 5-3. 2. Press the blower button to start the unit. The unit will run a self-test for approximately 15 seconds. Additionally, you will be instructed to “Please Wait” for three minutes to allow the cabinet to reach proper operating conditions. If the alarm sounds, recheck the sash position.
Chapter 5: Using The Cabinet The Logic Touchpad The touchpad of the Cell Logic Biosafety Cabinet is shown in Figure 5-4. Take a moment to get familiar with the buttons, their location and function. Also familiarize yourself with the display located on the right side wall.
Chapter 5: Using The Cabinet Figure 5-5 34 Product Service 1-800-522-7658
Chapter 5: Using The Cabinet Product Service 1-800-522-7658 35
Chapter 5: Using The Cabinet 36 Product Service 1-800-522-7658
Chapter 5: Using The Cabinet Product Service 1-800-522-7658 37
Chapter 5: Using The Cabinet User Selectable Features The Purifier Cell Logic Biosafety Cabinet offers the user unparalleled flexibility and convenience. The operation of the blower, fluorescent and UV lights can either be operated manually, or you may choose to use the SmartStart™ or Night-Smart™ features that activate functions automatically when the sash is opened or closed. The UV lamp can be programmed to operate for a given time interval when the sash is closed, before it shuts off.
Chapter 5: Using The Cabinet Interval Timer Operation 1. When selected, the Interval Timer menu is displayed on the LCD. The timer defaults to 0:00:00 (hours:minutes:seconds). 2. Press and hold the “▲” or “▼” buttons to increase or decrease the timer interval. 3. When the proper interval is entered on the display, press the “OK” button to start the timer. 4. When the timer reaches 0:00:00, an audible alarm will sound, and the timer will reset itself and repeat the countdown . 5.
Chapter 5: Using The Cabinet UV Lamp Timer The UV Lamp Timer allows you to decide whether the UV lamp will operate continuously or for a time period that you select. Interval When the “Interval” option is selected, the UV Interval Timer menu is displayed. UV Interval Timer This window lets you set the amount of time the UV lamp stays lit when activated. Use the “▲” and “▼” buttons to select the amount of time you need, then press the “OK” button to set the interval.
Chapter 5: Using The Cabinet Light Operation This menu option allows you to select whether the fluorescent lights will turn on automatically every time the sash is opened. NOTE: The fluorescent lights will automatically turn off when the sash is closed, no matter what its setting is. Smart-Start When the “Smart-Start” option is selected, the fluorescent lights will turn on every time the sash is opened.
Chapter 5: Using The Cabinet Light Hourmeter This display only shows the hours the fluorescent lamps have been lit and how many hours remain until you receive a warning to replace the lamps. Change Light Life In this option, you can set the hourmeter before you get the replace light warning. For most fluorescent lamps, the output of light decreases at a constant rate. Typically, after 6,000 hours of operation the lamp will output less light than it did when it was new.
Chapter 5: Using The Cabinet Security Lock NOTE: The security lock automatically reactivates and locks out the keypad every time the blower is shut off, by the keypad or by closing the sash. After the initial auto diagnostic screen is cleared, the security lock reactivates. The security lock feature prevents operation of the Biosafety Cabinet by unauthorized users. To engage the security lock, access the Security Lock submenu, as described in Figure 5-4.
Chapter 5: Using The Cabinet Restoring Software Default Settings To restore the default settings to their original configuration: 1. Access the Menu, and select “Cabinet Set Up”. Press “Mute/OK” 2. In the Cabinet Set Up submenu, select “Restore Defaults”. Press “Mute/OK” 3. Press “Mute/OK” again to restore the software defaults. Pressing “Menu” will escape this submenu without restoring the defaults.
Chapter 5: Using The Cabinet If An Airflow Alert Activates The most common causes of an Airflow Alert are: • Blockage of the inlet grilles or exhaust outlet. • Removal of the work surface or grille during operation. Resetting the Airflow Alert System The Airflow Alert automatically resets to normal operation once the motor speed has stabilized. Working In the Biosafety Cabinet Planning • Thoroughly understand procedures and equipment required before beginning work.
Chapter 5: Using The Cabinet Wipe-Down • Raise the sash to its full open position (approximately 21.75 inches or 552 mm). Mute the alarm by depressing the "Alarm Silence" switch. • Wipe down the interior surfaces of the cabinet with 70% ethanol, or a suitable disinfectant, and allow to dry. Loading Materials and Equipment • Only load the materials required for the procedure. Do not overload the cabinet. • Do not obstruct the front, side, or rear return air grilles.
Chapter 5: Using The Cabinet Final Purging • Upon completion of work, the cabinet should be allowed to operate for two to three minutes undisturbed, to purge airborne contaminants from the work area. Unloading Materials and Equipment • Objects in contact with contaminated material should be surface decontaminated before removal from the cabinet. • All open trays or containers should be covered before being removed from the cabinet.
Chapter 6: Maintaining the Cabinet The common service operations necessary to maintain the Biosafety Cabinet for peak performance are listed below. Note: This manual covers operation and maintenance operations for the owners/users of the Cell Logic Biosafety Cabinets. Complete certification procedures, service operations and specifications are published in a separate publication Technical Manual: Purifier® Logic® Biosafety Cabinets and PuriCare® Procedure Stations.
Chapter 6: Maintaining The Cabinet • Check the UV and fluorescent light hourmeters, and record their readings in an operational log. • All weekly activities. Semiannually or Annually • Have the cabinet re-certified by a qualified certification technician. • All monthly activities. Service Operations Work Surface Removal: Note: The work surface of the cabinet must be thoroughly decontaminated before removing it.
Chapter 6: Maintaining The Cabinet 4. Reinstall the grille by reversing the above sequence, ensuring that the grille properly engages the bottom edge of the cabinet. Figure 6-1 Towel Catch Removal: Although not normally required, the towel catch can be removed for cleaning, inspection, etc. Note: The work surface of the cabinet and the towel catch must be thoroughly decontaminated before removing either. 1. Remove the work surface as described above. 2.
Chapter 6: Maintaining The Cabinet Figure 6-2 Front Panel Removal and Installation: Figure 6-3 1. Locate and remove the two Phillips screws that secure the front panel as shown in Figure 6-3. They are located on the bottom corners of the front dress panel. 2. Swing the bottom of the dress panel out to clear the fluorescent light and then lift the front dress panel straight up and away from the cabinet.
Chapter 6: Maintaining The Cabinet Figure 6-4 1. To reinstall the panel, reverse these steps, ensuring that the plastic pin in the top corners of the dress panel properly engage the corner posts. Changing the Fluorescent Lamps: 1. Unplug the cabinet or turn off the System Reset Switch located on the top of the cabinet. 2. Remove the front dress panel as noted in Figure 6-3. 3.
Chapter 6: Maintaining The Cabinet 4. Unplug the cabinet or turn off the System Reset Switch, located on the top of the cabinet. 5. Remove the UV lamp by rotating it 90 degrees and lifting it straight up and out of its sockets. 6. Install new lamp by reversing the removal procedure. Resetting a Circuit Breaker: To reset any of the circuit breakers located on the left side of the electronics module, depress the white button until it sets.
Chapter 7: Troubleshooting Refer to the following table if the Biosafety Cabinet fails to operate properly. If the suggested corrective actions do not solve the problem, contact Labconco for additional assistance. PROBLEM CAUSE CORRECTIVE ACTION Cabinet blower and lights won’t turn on Unit not plugged into outlet Plug the Biosafety Cabinet into appropriate electrical service. Check connection to control box on top of Cabinet.
Chapter 7: Troubleshooting PROBLEM CAUSE Fluorescent light not Sash is closed working Fluorescent light is dim or flickering UV light not working UV light is dim or flickering CORRECTIVE ACTION Open sash – Fluorescent lights will not work with the sash closed. Lamp(s) are defective Replace defective lamp(s) Lamp wiring is disconnected Inspect lamp wiring. Defective lamp ballasts Replace lamp ballasts. Keypad disconnected or defective Run keypad diagnostics and check connections.
Chapter 7: Troubleshooting PROBLEM CAUSE CORRECTIVE ACTION Airflow Alert goes off and/or there is a slight decrease in filter life remaining gauge HEPA filter loading The gauge reading steadily decreases as the Cabinet is used. Blockage of the return air slots or grille Check all return air slots and grilles to ensure that they are not blocked or restricted. Blockage of the exhaust outlet Ensure that the exhaust outlet is not blocked or restricted.
Appendix A: Components Illustration A-1 indicates the location of the following service parts, and replacement accessory parts: Biosafety Cabinet Replacement Parts Item Quantity Part No.
Appendix A: Components A-1 1 2 3 4 5 6 58 Product Service 1-800-522-7658
Appendix B: Dimensions All dimensions in inches. B-1 Width “A” “B” “C” 3' 4' 5' 6' 42.3 54.3 66.3 78.3 36.5 48.5 60.5 72.5 13.6 19.9 26.9 32.9 *When equipped with Postfilter 68.
Appendix B: Dimensions B-2 60 Product Service 1-800-522-7658
Appendix C: Specifications Electrical Data Cabinet Model 34309 Series 34409 Series 34509 Series 34609 Series Electrical Requirements 115 VAC – 60 Hz, 1 Phase – 12 Amps 115 VAC – 60 Hz, 1 Phase – 12 Amps 115 VAC – 60 Hz, 1 Phase – 16 Amps 115 VAC – 60 Hz, 1 Phase – 16 Amps Motor Specifications Cabinet Model All 3- and 4-foot Cabinets, all Voltages Electrical Requirements Electronically Commutated Motor (ECM) 120-277 VAC – 50/60 Hz, 7.7 Full Load Amps @115VAC 4.3 Full Load Amps @230VAC 1/2 H.P.
Appendix C: Specifications Environmental Conditions 62 • Indoor use only. • Maximum altitude: 12000 feet (3657 meters). • Ambient temperature range: 41° to 104°F (5° to 40°C). • Maximum relative humidity: 80% for temperatures up to 88°F (31°C), decreasing linearly to 50% relative humidity at 104°F (40°C). • Main supply voltage fluctuations not to exceed ±10% of the nominal voltage. • Transient overvoltages according to Installation Categories II (Overvoltage Categories per IEC 1010).
Appendix D: Accessories Note: Accessories marked with an asterisk (*) require a qualified certifier to install and/or calibrate before use. Telescoping Base Stands These stands are available with either fixed feet or caster wheels. The user sets the height of these stands before installation. The height can be set from 27.5 to 33.5 inches in 1-inch intervals, providing a cabinet work surface height of 30.0 to 36.0 inches. The Base Stands for each Purifier Cell Logic Series are listed below.
Appendix D: Accessories Hydraulic Base Stand Shelf Kit (# 3850200) This 22 ¼ x 11 ¼-inch long shelf is specifically designed to hold the Aspirator Pump or other small accessories, and attaches to the lower left side of the base stand. The kit includes shelf and self-drilling fasteners. NOTE: A power drill with a 5/16-inch socket is needed to attach the fasteners to the base stand.
Appendix D: Accessories IV Bar Kits Bar supports intravenous solution bottles and bags. Kits include IV bar, mounting hardware, and four hangers. Catalog # 3858600 3858601 3858602 3858603 For use with 3-foot Purifier Cell Logic 4-foot Purifier Cell Logic 5-foot Purifier Cell Logic 6-foot Purifier Cell Logic Shipping Weight 3 lbs. (1.4 kg) 4 lbs. ( 1.8 kg) 5 lbs. (2.3 kg) 6 lbs. (2.7 kg) Shelf (# 3859000) The wire shelf measures 8 inches wide by 5 inches deep, with a weight capacity of 2.2 lbs.
Appendix D: Accessories *Postfilter Conversion Kit These kits allow the retrofitting of carbon postfilters in Logic cabinets that originally did not have this option. Catalog # 3859301 3859302 3859303 For use with 4-foot Purifier Cell Logic 5-foot Purifier Cell Logic 6-foot Purifier Cell Logic Shipping Weight 5 lbs. (2.3 kg) 5 lbs. (2.3 kg) 5 lbs. (2.
Appendix D: Accessories Ergonomic Chair with Armrests (# 3744000) Lab chair has 6-way articulating seat and back control for personalized adjustment. Pneumatic mechanism adjusts seat height from 18 1/4" to 25 3/4". Five-leg black reinforced composite base rests on 2" ball bearing casters. Aluminum support ring. Removable arm rests. Black vinyl upholstery. Shipping weight 35 lbs. (15.9 kg). Adjustable Footrest (# 3746000) Elevates feet and permits angle repositioning while in use.
Appendix D: Accessories Pure-Vu Air Barrier Seals Used to seal microscopes on Cell Logic Biosafety Cabinets with ScopeReady package. Note: Stereo microscope’s eyepieces have a broad range of eyepiece height movement and will usually require the pleated Pure-Vu XL Seal sizes, 4027810 and 4027811. Contact Labconco for ordering information on Pure-Vu Seals for microscopes not listed.
Appendix D: Accessories Stand-Still Isolation Platforms Used to support microscopes, isolate vibration, and promote airflow containment. 4028200 Stand-Still Isolation Platform (Std. Size 12" (305 mm) wide x 18.75" (476 mm) deep x 1.5" (38 mm) high. 4028100 Stand-Still XL Isolation Platform (Extended Size 12" (305 mm) wide x 22.75" (578 mm) deep x 1.5" (38 mm) high. Typically used with stereo microscopes requiring forward extended support.
Appendix E: Quick Chart Model Cabinet Size (in feet) Sash Opening (inches) Starting Serial #1 Nominal Avg. Downflow (FPM) Nominal Average Inflow (FPM) Supply HEPA Data Labconco P/N Exhaust HEPA Data Labconco P/N Motor/Blower Data Labconco P/N2 Motor HP Blower Size (inches) Fluorescent/UV Lamp Data Fluorescent Lamps (2 each) Light intensity (ft-candles)3 UV Lamp UV energy(uW-cm2)4 Prefilter Data Labconco P/N Postfilter Data Labconco P/N Canopy Data Avg. Exhaust Vol. Range (CFM) Canopy Alarm Setpoint Vol.
Appendix F: Installation Guide for all Pure-Vu Seals and Stand-Still Isolation Platforms Figure F-1 is an aid to show the proper installation of the pure-Vu Seal for the Cell Logic Biosafety Cabinet with Scope-Ready Package. Figure F-1 also shows the proper placement of the Stand-Still Isolation Platform.
Appendix F: Installation Guide Pure-Vu Seals/Stand-Still Isolation Platforms Figure F-2 is an aid to show the Pure-Vu Seal fully installed with the eyepieces extended and sealed. Figure F-2 also shows the microscope moved forward into proper position on the Stand-Still Isolation Platform.
Appendix F: Installation Guide Pure-Vu Seals/Stand-Still Isolation Platforms Stereoscopes with forward extending bases and frequent eyepiece height adjustment typically require the selection of a Pure-Vu XL Seal and StandStill XL Isolation Platform. Figures F-3 through F-10 are an aid in setting up the pleated Pure-Vu XL Seal. Figures F-11 and F-12 show typical complete installations of stereo microscopes and proper placement of the Stand-Still XL Isolation Platform.
Appendix F: Installation Guide Pure-Vu Seals/Stand-Still Isolation Platforms 3. Per Figure F-5, form the second pleat and secure with transparent tape. Figure F-5 4. Per Figure F-6 and Figure 3-5, place the Outer Aerodynamic collar over the Pure-Vu XL Seal and lightly secure in place with the 14 Phillips mounting screws. Do not tighten. Figure F-6 5. Per Figure F-7, remove the transparent tape and then tighten the 14 Phillips mounting screws.
Appendix F: Installation Guide Pure-Vu Seals/Stand-Still Isolation Platforms 6. Per Figure F-8, move the microscope forward through the holes in the Pure-Vu Seal and install the eyepiece. A tight seal should be formed around the eyepiece. Figure F-8 7. Figure F-9 shows the finished installation. Figure F-9 8. Per Figure F-10, adjust the scope eyepiece height for proper focus for the specimen range.
Appendix F: Installation Guide Pure-Vu Seals/Stand-Still Isolation Platforms 9. Figure F-11 shows the completed installation of the Pure-Vu XL Seal and Stand-Still XL Isolation Platform for one scope manufacturer. The Pure-Vu XL Seals extend 5.5" below the aerodynamic collar.
Appendix F: Installation Guide Pure-Vu Seals/Stand-Still Isolation Platforms 10. Figure F-12 shows a different installation of the Pure-Vu XL Seal and Stand Still XL Isolation Platform for another separate scope manufacturer. Figure F-12 11. Refer to Appendix D: Accessories to order Pure-Vu Seals and Stand Still Isolation Platforms and use Chapter 3 and Appendix F as an aid for proper setup.
Appendix F: Installation Guide Pure-Vu Seals/Stand-Still Isolation Platforms Pure-Vu Template Note: Not to scale, see next page.
Appendix F: Installation Guide Pure-Vu Seals/Stand-Still Isolation Platforms Product Service 1-800-522-7658 79
DECLARATION OF CONFORMITY Application Council Directive(s): 73/23/EEC, 89/336/EEC, 2002/95/EC (RoHS), 2004/108/EC Standard(s) to which conformity is declared: EN61010-1, EN55022, EN61000-3-2/3, EN61326-1 Manufacturer’s Name: Labconco Corporation Manufacturer’s Address: 8811 Prospect Avenue Kansas City, MO 64132 USA Importer’s Name: See Shipping/Customs Documents Importer’s Address: See Shipping/Customs Documents for your equipment Type of Equipment: Laboratory Equipment Model No.
