Quick Start Guide

24 C Series Quick Start Guide 25
Appendix
Maintenance
During normal operation your C Series amplier will provide trouble-free service. The only user maintenance required is to periodically vacuum clean the foam dust
lters behind the front grille.
In some extreme cases it may be necessary for authorized service personnel to clean the inside of the amplier. These conditions usually occur after prolonged use in
extreme environments such as those using “cracked oil” smoke machines. If you are using your amplier in a heavy duty application, it is recommended to have your
amplier serviced every three years purely as a preventative action.
FAQ
Following are common questions asked about Lab Gruppen C Series power ampliers together with helpful answers.
Q: What is the input sensitivity of the ampliers?
A: Input sensitivity is calculated from the amplier gain, maximum output voltage and load. As gain and output voltage are adjustable in C Series ampliers, you
need to look this information up in a table found in the Appendix section of this manual. Input sensitivity also is automatically calculated in the DeviceControl
softwareapplication.
Q: What are the maximum cable lengths allowed when using the NomadLink network?
A: NomadLink uses a daisy-chain topology to connect ampliers and an NLB 60E in a network. Standard RJ45-equipped Cat-5 cables are used throughout. The daisy
chain may be made into a closed-loop by connecting a return cable to the NLB 60E from the last amplier.
General rules of cable lengths:
• The maximum cable length in between any two devices may not exceed 300meters / 980feet.
• In a non-closed-loop daisy-chained subnet the maximum cable length is 400meters / 1300feet.
• In a closed-loop subnet the maximum cable length is 700meters / 2300feet.
Exceeding these limits may result in lost contact with the devices, or loss of phantom powering due to cable resistance.
Q: How long can cable-runs be on the Ethernet network connecting the NLB 60E to the PC?
A: On the Ethernet side, normal Ethernet cable limits apply. This is typically a maximum of 80meters / 300feet between each device. Follow standard installation
procedures for Ethernet. Distances beyond 100meters may require use of a repeater, a format converter, or optical cables.
Q: Why is the NomadLink network a closed-loop topology?
A: Technically speaking, the closed loop is optional. The purpose of closing the loop is primarily to provide a secondary path to the ampliers. If cables are broken or
disconnected in either direction, all ampliers still may be addressed by the network.
Q: How can I be sure that no protection circuits or safety functions interfere with the output signal?
A: If no Clip or Warning LEDs on the front panel light up, you can be fully condent that the rated maximum output power in the full frequency range is available for
your speakers. No limiting or gain-reduction takes place without a warning or fault indication.
Additional documentation
In case you didn’t nd what you were looking for in this Operation Manual, check out the website at www.labgruppen.com, where you can nd a multitude of
additional documentation for C Series.
Current Draw and Thermal Dissipation Specications
The following tables contain information on measured current consumption as well as calculated heat dissipation during normal operation (⁄ rated power); and
during extreme heavy duty operation (¼ rated power).
C 88:4
Level Load Rated power
Line Current *2) Watt *1) Thermal Dissipation
115 VAC 230 VAC In Out Dissipated BTU/hr kCal/hr
Standby with remote power o via NomadLink 0 0 0 0 0
Powered on, idling. 139 0 139 475 120
Amp (I) Watt
Pink noise
(⁄ rated power)
8Ω / Ch. 1250 x 4
17.6 8.8 1177 625 552 1884 475
16Ω / Bridged 2500 x 2
4Ω / Ch. 2100 x 4
27 13.5 1914 1050 864 2949 743
8Ω / Bridged 4200 x 2
2Ω / Ch.
*4)
2200 x 4
33.6 16.8 2221 1150 1071 3655 921
4Ω / Bridged
*4)
4400 x 2
100V / Ch. 2000 x 4
26.2 13.1 1838 1000 838 2860 721
200V / Bridged N/R
Pink noise
(max power)
*3)
8Ω / Ch. 1250 x 4
30.0 16.0 2006/2140 1145/1221 860/918 2935/3133 739/789
16Ω / Bridged 2500 x 2
4Ω / Ch. 2100 x 4
30.0 16.0 2127/2268 1230/1312 896/956 3058/3263 770/822
8Ω / Bridged 4200 x 2
2Ω / Ch. 2300 x 4
30.0 16.0 1983/2115 1016/1084 966/1031 3297/3519 831/886
4Ω / Bridged 4600 x 2
100V / Ch. 2000 x 4
30.0 16.0 5992/2236 3467/1294 883/942 3014/3216 759/810
200V / Bridged 4000 x 2
Mains connector, 230V CE version 16 A, CEE7
Mains connector, 115V ETL version 30A Twist Lock
*1) The amplier’s PSU operates as a non-resistive load, so the calculation “Volts x Amps = Watts” would not be correct. Instead, measured and specied here is what
is known as the “Active Power” in the amplier providing useful, real-world values of power consumption and heat dissipation.
*2) Current draw gures measured at 230V. 115V gures are 230V gures multiplied by two.
*3) Figures measured at maximum sustainable power without tripping the mains fuse. Listed separately for 30 A/115V and 16 A/230V operation. Note that the max.
power condition is very extreme and will not occur during normal operation. Also note that the mains breaker will not be tripped even if operation is momentarily in
excess of max. ratings.
*4) Italics used for conditions that, if sustained over long time periods, may trigger the mains breaker. Therefore these measurements should not be used when calculating
cooling requirements as they cannot be sustained by the mains breaker over time.