ASSEMBLY Instructions Big & Tall Executive Chair
Should you prefer to speak with a customer service representative, you may call toll free : 1-855-372-2315 0-800-051-6775 2 U.S. 6am - 5pm PST, U.K.
Guidelines FAILURE TO FOLLOW THESE WARNINGS WHEN IN USE COULD RESULT IN INJURY • Do not stand on the item or use as a step ladder. • The piece has been tested and approved for users weighing up to 350lbs (159 kg) per seat. • Do not use this item unless all bolts and screws are firmly secured and fastened. • Check all bolts and screws every 90 days. As necessary tighten if any are loose. • Lift up then move.
Pre-Assembly Preparation: Please read through this instruction booklet before beginning assembly of this item. Two adults are recommended for assembly. • Clear out the space for assembly and lay out all parts on Parts List, extra room will allow you to easily determine if all the pieces are present. • Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware. • Keep small parts and pieces away from children and pets until fully assembled.
Parts List D1 A Casters Quantity: 5 F Seat Cushion Quantity:1 K 1-1/4” Screws Quantity: 4 B Star Base Quantity: 1 G Back Cushion Quantity: 1 C Gas Lift with Telescoping Cover Quantity: 1 H Quantity: 4 Quantity: 2 M N Plastic Caps Allen Key M5 Quantity: 4 D2 E Arms Quantity: 2 J 1” Screws Quantity: 1 2-3/4” Screws with Spring Washers Quantity: 1 I Plastic Shroud L D Seat Plate 1-3/4” Screws Quantity: 2 Quantity: 1 5
Step 1 Step 2 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). Turn the Star Base (B) over and insert the Gas Lift with Telescoping Cover (C) through the center hole on top of Star Base (B).
Step 3 Step 4 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using 1-3/4” Screws (J) for the front holes of the Seat Plate (D) and 1” Screws (I) for the rear holes of the Seat Plate (D) and tighten screws. *Note: Tighten the screws completely.
Step 5 Step 6 Attach the Back Cushion (G) to the Seat Cushion (F) by positioning the back support plate over the Seat Plate (D) with 1-1/4” Screws (K). *Note: Do not tighten the screws completely. Insert 2-3/4” Screws with Spring Washers (L) into arm holes, attaching Arms (E) (with the front of arms facing the front of seat cushion) to sides of Seat Cushion (F) and Back Cushion (G). *Note: Tighten all the screws completely. Remember to tighten the back support plate screws.
Step 7 Step 8 Put the Plastic Shroud (H) over the Seat Plate (D) (with the front of plastic shroud facing the front of seat cushion). Align shroud posts to holes on bottom of Seat Cushion (F) and press into position. Position the assembled chair upright with the seat plate facing down. Insert the Gas Lift with Telescoping Cover (C) into the center hole of the Seat Plate (D).
Step 9 Press the Plastic Caps (M) into armrest holes once all screws have been tightened.
Operating Instructions Function Instruction - 1 To Adjust Seat Height: While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release lever to lock chair at desired height. To lower the seat, lift the lever while seated. The chair will descend until the lever is released or the chair reaches the bottom position.
Function Instruction - 3 To Adjust Tension on the Tilt: Reach under the front center of the chair, grasp the round knob (R) and turn it counter- clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user. Rotate the knob (R) until the desired resistance is reached. R 12 Function Instruction - 4 360˚ Swivel: 360˚ seat swivel.
Limited Warranty The product you have purchased is warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases these products from an authorized dealer or retailer as shown by the original sales receipt. This warranty does not apply too “as is” or previously owned products.
