2.
05 06 06 Auto-Dim Settings Display Modes Display Mode Options Purchase Information Add-On Sensor Setup Lost Connection Low Battery 11 11 12 12 13 13 14 14 Wireless Phone Charger Phone Compatibility Adjustable Charging Coil USB Charging Ports Earbud Charging Accesory Storage Smart Watch Stand Cable Organizer 16 16 15 15 05 LCD Display Brightness 18-20 Cautions/Statements Stay in Touch Support Information SUPPORT 21 21 20 18 Recycling & Disposal Trademarks & Warning 1
Scroll to rotate the projection image (left or right) 8. ROTATION WHEEL Press to adjust projection intensity. Hold to change projection mode* 5. PROJECTION Press to decrease values, hold to change values quickly 2. MINUS - 6. 3. SET 7 5 Top View 4 Press to activate/deactivate alarm. Hold to enter alarm settings ALARM Hold to enter Settings Menu 3 *An add-on sensor is required for additional projection options. See p.15 for details. Press to adjust backlight or snooze a sounding alarm.
The icon will appear on the LCD when activated. 4. Press the +/- buttons to adjust the stopping hour. Press the SNOOZE/ BACKLIGHT to confirm and exit. 2. Press the +/- buttons to turn the Auto-Dim feature on or off. Press the SNOOZE/BACKLIGHT to confirm. 3. Press the +/- buttons to adjust the starting hour. Press the SNOOZE/ BACKLIGHT to confirm. 1. Hold the SNOOZE/BACKLIGHT button to enter the Auto-Dim Settings Menu.
07 4. Your time alarm is now activated, indicated by the icon on the LCD. 3. Next, use the +/- buttons to set your desired snooze duration (5 to 120 minutes). Press the ALARM button to confirm and exit the Alarm Settings Menu. 2. The icon will appear on the normal time display when the alarm is active. 1. Press the ALARM button to activate/deactivate the alarm (ON/OFF). Snooze Duration Countdown When the snooze time reaches “00,” the alarm will sound again.
Note: The fixed focus projection image will look best at about 7ft. (2.1m). 09 The Projection Arm tilts forwards and backwards to adjust the location of the projection image. Use the Rotation Wheel on the Projection Arm to rotate the viewing angle of the image. Press the PROJECTION button to adjust the projection’s brightness (HI/LOW/OFF).
Compatibility may vary based on phone model and/or case selection. This list is not comprehensive. Please check your phone’s manual for details regarding Qi-Enabled capabilities. Works with all Qi-Enabled phones, such as: • iPhone 8 or newer • Galaxy S8 or newer • Galaxy Note 8 or newer Phone Compatibility • The light will flash slowly if your device is not positioned properly or if your device is not compatible with the Qi wireless charging technology.
Use the included Cable Organizer to keep your charging cords neat and secure. Insert the organizer into the Cable Clip Keyhole and slide it down to lock in place. Lift up and pull the Cable Organizer out to remove it. Accessory Storage The Earbud Dock, Cable Fittings, and Smart Watch Stand can all be stored in the Accessory Compartment on the bottom of the clock when not in use. Cable Organizer Note: Smartwatch and charging cords not included. 5.
Outdoor Temp/Humidity The sensor’s data should then be viewable on your LCD and as an option to be projected. Projection Image outdoor 15 3. Press the TX button inside the sensor battery compartment to transmit a signal. 2. Hold the + button on the clock to search for the sensor. 1. Insert 2 “AA” Batteries into the sensor battery compartment. Add-On Sensor Set Up Search for the compatible sensor using the alarm clock’s model number (C75709).
8.39 in. (21.31 cm) Programmable Snooze Duration: 5 to 120 Minutes LCD Brightness: 4 Intensity Levels + OFF (Programmable Auto-Dim Backlight Option) Projection Brightness: 2 Intensity Levels + OFF Power Requirements: 9.0V Power Cord (Included) HX25-0902500-AU CR2032 Battery for backup (Included) The plug on the power adapter is intended to serve as the disconnect device, the socket-outlet shall be installed near the equipment and shall be easily accessible. 1.80 in. (4.
FCC Radiation Exposure Statement This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
For detailed product videos, manuals, and more visit our support website: bit.ly/c75709_support If you need additional assistance, contact our friendly customer support team: Online: bit.ly/contact_techsupport Phone Number: 1.877.408.2678 Representatives available Monday-Friday, 8:00am to 6:00pm CST. Ask questions, watch set up videos, and provide feedback on our social media outlets. Follow La Crosse Technology on Youtube, Twitter, Facebook & Instagram.
