Installation Guide

Page 3 Page 5Page 2 Page 4
WIFI WIND & WEATHER
STATION
WITH FORECAST
QUICK START GUIDE
MODEL#: S82950
DC: 012619
Full manual can be found under the SUPPORT tab here: bit.ly/s82950
STEP 1:
POWER UP SENSORS AND STATION
STEP 2:
CONNECT TO THE LA CROSSE VIEW
®
APP
SENSORS
In any order, insert batteries into your Thermo-Hygro, Wind,
and Water Leak Sensors.
WIND STATION
• Insert the power cord into an outlet, then into your Wind Station.
• Remove the battery insulation tab installed on the bottom of the
station.
Note: It may take up to 10 minutes for your sensor data to appear
on your station’s screen.
AA
+
-
AA
+
-
Thermo-Hygro Sensor
LTV-TH2
Slide down
to open.
Twist left
to open.
Turn left
to open.
Wind Station
S82950
Power
Cord
C C
Wind Sensor
LTV-W1
Water Leak Sensor
LTV-WL1
BATTERY FOR
BACKUP ONLY
CR2032
AA
+
-
AA
+
-
STEP 3:
MOUNT YOUR SENSORS
THERMO-HYGRO
Keep out of direct sunlight & ensure the sensor is well ventilated.
We recommend mounting under a deck or eave facing north.
WIND
Ensure the sensor is mounted vertically, an unobstructed rooftop is
ideal. Your Wind Sensor should be the tallest object in the area to
avoid reduced wind speed values.
WATER LEAK
Works best placed flat on the floor. It will detect water at
0.031inches (0.787 mm). When placed vertically the water needs to
be at least 0.25 inches (6.35 mm) to trigger the alert.
FEATURE STANDALONE CONNECTED
Wind Speed ✓ ✓
Wind Direction ✓
Indoor & Outdoor Temperature ✓ ✓
“Feels Like” Temperature ✓ ✓
Indoor & Outdoor Humidity ✓ ✓
12-Hour Forecast ✓ ✓
Barometric Pressure ✓ ✓
Internet Time & Calendar ✓
AccuWeather Forecast ✓
Daily Forecast HIs & LOs ✓
% Chance of Precipitation ✓
Ability to Add Sensors ✓ ✓
Data Stream Technology ✓
Water Leak Detection ✓ ✓
Benefits of Connecting to La Crosse View
ADD-ON SENSORS
Whether you choose to connect with the La Crosse View app or
not, this station has the ability to display data for up to 4 additional
sensors (like the included Water Leak Sensor).
A full list of compatible sensors can be found under the PARTS tab
here: bit.ly/s82950
Water Leak Sensor Example
ADD EXTRA SENSORS TO YOUR WIND STATION
1. Hold the EXTRA SENSOR button until you see the Sensor
Reception Indicator start to animate.
2. Install batteries into your sensor, if it has a TX button press it to
force a transmission signal.
3. Your sensor should connect within the next 3 minutes, briefly
displaying its ID and type. The Sensor Reception Indicator will
show solid on screen when a sensor is connected.
4. Press the EXTRA SENSOR button to cycle through the data
you’d like displayed on screen.
5. To add sensors to your La Crosse View app, watch this video:
bit.ly/LaCrosseView_Support_Vid_10
Note: When first powering up, or after a factory restart, extra
sensors should automatically connect with your display.
DOWNLOAD
Visit the App Store or Google Play Store to download the free
LaCrosse View™ app onto your mobile device.
LAUNCH & FOLLOW
Open the LaCrosse View™ app and follow the on-screen
instructions.
GET YOUR STATION READY
Ensure your station’s Wi-Fi Indicator is flashing. If it is not, press
and hold the Plus (+) and Minus (–)button down together until it
begins flashing. This tells you that your station is ready to connect.
HAVING TROUBLE CONNECTING?
Make sure your mobile device is connected to your router’s
2.4GHz Wi-Fi network, and that you’ve correctly entered your
Wi-Fi password.
For more troubleshooting tips and support visit:
www.lacrossetechnology.com/lacrosseviewsupport