WEATHER STATION Instruction Manual INTRODUCTION: Congratulations on purchasing this state-of-the-art weather station as an example of innovative design and quality piece of engineering. Providing radio controlled time, calendar, weather forecast, moon phase, indoor and outdoor temperature, indoor and outdoor relative humidity. This unit will never keep you guessing on current and future weather conditions. Operation of this product is simple and straightforward.
Weather forecasting with weather tendency indicator Indoor and outdoor temperature display with MIN/MAX records Temperature display in ºC/ ºF Indoor and outdoor humidity display Humidity data display as RH% Low battery indicator Table standing or wall mounting Thermo-Hygro Transmitter Remote transmission of outdoor temperature and humidity to weather station by 915MHz Wall mounting case Mounting at a sheltered place.
1. 2. 3. Remove the battery cover. Insert the batteries, observing the correct polarity (see battery compartment marking). Replace the battery cover on the unit. Note: In the event of changing batteries in any of the units, all units need to be reset by following the setting up procedures. This is due to a random security code assigned by the transmitter at start-up. This code must be received and stored by the weather station in the first 3 minutes of power being supplied to the transmitter.
. step 1. In order to ensure sufficient 915 MHz transmission however, the distance between the Weather Station and the transmitter should not be more than 330 feet (100 meters) (see notes on “Positioning” and “915 MHz Reception”). Note: In the event of changing batteries of the units, ensure the batteries do not spring free from the contacts. Always wait at least 1 minute after removing the batteries before reinserting, otherwise start up and transmission problems may occur.
LCD SCREEN The LCD screen is split into 5 sections displaying the information for time/calendar, weather forecast, moon phase, indoor data, and outdoor data.
To set the time format in 12h or 24h display: 1. “12h” or “24h” will start flashing. (default 12h) 2. Press the + key to select the “12h” or “24h” display mode. 3. Confirm with the SET key and enter the “Manual time setting”. Note: When 12h mode display is selected, the calendar format will be "Month. Day" display. When 24h mode display is selected, the calendar format will be "Day. Month" display. MANUAL TIME SETTING: To set the time. Hour flashing 1. 2. 3. 4. 5.
3. 4. 5. 6. 7. Press the SET key again to confirm and to enter the month setting. The month starts flashing. Use the + key to set the month. Press the SET key again to confirm and to enter the date setting mode. The date starts flashing. Use the + key to set the date. Confirm all calendar settings with the SET key and “ºF/ºC temperature display setting”. °F/°C TEMPERATURE UNIT SETTING flashing The default temperature display is set to °F (degree Fahrenheit). To select °C (degree Celsius): 1.
WEATHER FORECAST AND WEATHER TENDENCY: WEATHER FORECASTING ICONS: The weather icons in the second section of LCD can be displayed in any of the following combinations: Sunny Cloudy with sunny intervals Rainy For every sudden or significant change in the air pressure, the weather icons will update accordingly to represent the change in weather. If the icons do not change, then it means either the air pressure has not changed or the change has been too slow for the Weather station to register.
If the weather station is moved to another location significantly higher or lower than its initial standing point (for example from the ground floor to the upper floors of a house), discard the weather forecast for the next 12-24 hours. By doing this, the Weather Station will not mistake the new location as being a possible change in airpressure when really it is due to the slight change of altitude.
Low battery indicator (transmitter) Outdoor temperature in ºC/ºF Outdoor data signal reception indicator Outdoor relative humidity in RH% TOGGLING AND RESETTING THE MIN/MAX DATA TO VIEW THE MIN/MAX DATA Press the MIN/MAX key several times to view the MIN/MAX indoor temperature, and MIN/MAX outdoor temperature sequentially. TO RESET THE MIN/MAX DATA Press and hold MIN/MAX key for 3 seconds to reset all the indoor and outdoor temperature to current temperatures.
4. frequency may prevent correct signal transmission or reception. Neighbors using electrical devices operating on the 915MHz-signal frequency can also cause interference. Note: When the 915MHz signal is received correctly, do not reopen the battery cover of either the transmitter or weather station, as the batteries may spring free from the contacts and force a false reset. Should this happen accidentally then reset all units (see “Setting up” above) otherwise transmission problems may occur.
POSITIONING THE THERMO-HYGRO TRANSMITTER Mounting at a sheltered place. Avoid direct rain and sunshine. The thermo-hygro transmitter can be placed onto any flat surface or wall mount using the bracket which doubles as a stand or wall mount base. To wall mount: 1. Secure the bracket onto a desired wall using the screws and plastic anchors. 2. Clip the transmitter onto the bracket.
SPECIFICATIONS: Temperature measuring range: Indoor : 14.1°F to +139.8°F with 0.2°F resolution -9.9ºC to +59.9ºC with 0.1°C resolution (“OF.L” displayed if outside this range) Outdoor : -39.8°F to +139.8°F with 0.2°F resolution -39.9ºC to +59.9ºC with 0.1°C resolution (“OF.L” displayed if outside this range) Indoor humidity range: 20% to 95% with 1% resolution (Display “- -“ if temperature is OL.
La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of La Crosse Technology, Ltd and must be returned to La Crosse Technology, Ltd. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer.
PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT OF CHILDREN’S REACH. This warranty gives you specific legal rights. You may also have other rights specific to your State. Some States do no allow the exclusion of consequential or incidental damages therefore the above exclusion of limitation may not apply to you.
FCC ID: OMO-M-15 (transmitter) FCC DISCLAIMER RF Exposure mobile: The internal / external antennas used for this mobile transmitter must provide a separation distance of at least 20 cm (8 inches) from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter." Statement according to FCC part 15.19: This device complies with Part 15 of the FCC Rules.
