Installation & User Guide

14
Part Finish Recommended
cleaning method
Burner grates & top of
burner heads
Porcelain enamel Mildly abrasive
cleaner such as Bon
Ami® or Soft Scrub®.
Dishwasher.
Burner base Aluminum As above
Maintop top Stainless steel Hot soapy water, non-
abrasive cleaner, soft
cloth.
Sides, toe-kick Painted enamel Hot soapy water and
soft cloth.
Control panel Porcelain enamel or
stainless steel
Non-abrasive cleaner,
soft cloth.
Oven interior Porcelain enamel Branded oven cleaner
suitable for enamel
surfaces such as Dawn
Power Dissolver®. Take
care not to damage
the oven door seals.
Door handles Brass or plated brass/
plastic
Non-abrasive cleaner,
hot soapy water, soft
cloth. Brass handles
can be cleaned with a
gentle brass polish.
Oven racks & supports Chrome Dishwasher. Hot soapy
water and scouring
pad.
Door inner Porcelain enamel Mildly abrasive cleaner
such as Bon Ami® or
Soft Scrub® with a soft
cloth.
Outer door and drawer Porcelain enamel or
stainless steel
Multi-surface cleaner,
soft cloth.
Brass trims (some
models only)
Brass Non-abrasive cleaner,
hot soapy water, soft
cloth. Gentle brass
polish.
Copper trims (some
models only)
Copper Hot soapy water and
soft cloth.
Oven Liner Porcelain enamel Mildly abrasive cleaner
such as Bon Ami® or
Soft Scrub® with a soft
cloth.
5. Cleaning your range
Essential information
n
Before thorough cleaning, turn o the circuit
breaker. Allow the range to cool.
n
After cleaning remember to switch on the circuit
breaker before using the range.
NEVER use paint solvents, caustic cleaners, biological
powders, bleach, chlorine-based bleach cleaners, coarse
abrasives or salt.
DO NOT mix dierent cleaning products – they may react
together with hazardous results.
Recommended cleaning materials are shown in Table 5.1.
Cleaning the range – daily care
Cleaning the range is not a welcomed chore, but it has to be
done to maintain eciency and appearance. Remember, it
is better to wipe up any spills as they occur, this will prevent
them burning on and becoming more dicult to remove
later.
n
Make sure the ow of combustion and ventilation air
to the range is unobstructed – for example, by build-
up of fats or grease.
If the ame is distorted, check that the burner head is
correctly placed over the burner base (Fig. 5.1).
If the ame burns with a long white tip you should call for
service.
Cleaning for spills
For spills and boil-overs that occur while cooking, as soon
as possible turn o the burner and allow it to cool. DO NOT
clean until the area is completely cooled down. Wipe up spills
as soon as possible.
DO NOT allow surplus water to seep into the range.
Cooktop burners
The burner heads and caps can be removed for cleaning.
Make sure they are absolutely dry before replacing.
When replacing burner head, make sure this locates properly
within the base (Fig. 5.2). If you look at the bottom of the
burner head you will see two ‘pips’; these t into the two
notches in the burner base (Fig. 5.3). Check burner ports are
not blocked. If blockage occurs, remove stubborn particles
using a piece of fuse wire.
Stainless steel main top
Lift away pots or pans from main top. Remove grates from
spillage area and carefully place in a sink of warm soapy
water. Wipe loose debris from main top. Avoid using any
abrasive cleaners including cream cleaners on brushed
stainless steel surfaces. For best results use a liquid detergent
cleaner. Rinse with cold water and thoroughly dry with
a clean, soft cloth. Make sure all parts are dry before
repositioning.
Table 5.1