User Guide for the Kyocera 3225 phone This manual is based on the production version of the Kyocera 3225 phone. Software changes may have occurred after this printing. Kyocera reserves the right to make changes in technical and product specifications without prior notice. The products and equipment described in this documentation are manufactured under license from QUALCOMM Incorporated under one or more of the following U.S.
5,629,975 5,652,814 5,673,259 5,691,974 5,710,521 5,722,053 5,732,341 5,751,725 5,757,858 5,778,338 5,790,632 5,805,843 5,812,938 5,835,847 5,844,985 5,857,147 5,864,760 5,872,481 5,881,053 5,892,774 5,903,862 D410,893 5,920,284 5,926,786 5,638,412 5,654,979 5,675,581 5,692,006 5,710,758 5,722,061 5,734,716 5,751,761 5,758,266 5,781,543 5,793,338 5,812,036 5,818,871 5,839,052 5,848,063 5,859,612 5,864,763 5,872,774 5,881,368 5,892,816 D409,561 5,914,950 D411,823 5,930,230 5,640,414 5,642,398 5,644,591 5,6
Kyocera is a registered trademark of Kyocera Corporation. Brick Attack, Doodler, Race 21, FunLights and the arrangement of blue LEDs are trademarks of Kyocera Wireless Corp. QUALCOMM is a registered trademark, and BREW and BREW Shop are trademarks of QUALCOMM Incorporated. Tetris is a registered trademark of Elorg Company LLC. Openwave is a trademark of Openwave Systems Incorporated. eZiText is a registered trademark of Zi Corporation. All other trademarks are the property of their respective owners.
Other accessories used with this device for body-worn operations must not contain any metallic components and must provide at least 22.5 mm separation distance including the antenna and the user’s body. THIS MODEL PHONE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES. Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S.
Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output.
While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section http://www.fcc.gov/oet/fccid after searching on FCC ID OVFKWC-3225.
Warning Use only Kyocera approved accessories with Kyocera phones. Use of any unauthorized accessories (includes faceplates/front housings) may be dangerous and will invalidate the phone warranty if said accessories cause damage or a defect to the phone. Optimize your phone’s performance Use the guidelines on see page 3 to learn how to optimize the performance and life of your phone, antenna, and battery.
• Always keep the phone at least six inches (15 centimeters) away from your pacemaker when the phone is turned on. • Do not carry your phone near your heart. • Use the ear opposite the pacemaker. • If you have any reason to suspect that interference is taking place, turn off your phone immediately. Hearing aids—Some digital wireless phones may interfere with hearing aids.
Potentially unsafe areas Posted facilities–Turn your phone off in any facility when posted notices require you to do so. Aircraft–FCC regulations prohibit using your phone on a plane that is in the air. Turn your phone off before boarding aircraft. Vehicles–RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer of the device to determine if it is adequately shielded from external RF energy.
• transfer or storage facilities for fuel or chemicals • vehicles using liquefied petroleum gas, such as propane or butane • areas where the air contains chemicals or particles such as grain, dust, or metal powders • any other area where you would normally be advised to turn off your vehicle engine Use with care Use only in normal position (to ear). Avoid dropping, hitting, bending, or sitting on the phone. Keep phone dry If the phone gets wet, turn the power off immediately and contact your dealer.
Qualified service If you are experiencing problems with your phone, see “Getting Help” on page 127. If you have additional questions, contact your service provider for technical support. If the problem persists, return the phone with all accessories and packaging to the dealer for qualified service. Accessories Use only Kyocera-approved accessories with Kyocera phones.
guidelines are consistent with the safety standards previously set by both U.S. and international standards bodies in the following reports: • ANSI C95.1 (American National Standards Institute, 1992) • NCRP Report 86 (National Council on Radiation Protection and Measurements, 1986) • ICNIRP (International Commission on Non-Ionizing Radiation Protection, 1996) Your phone complies with the standards set by these reports and the FCC guidelines.
Battery and charger specifications Charger Input CV90-60858-1 100-240VAC / 50/60Hz CV90-61016-1 100-240VAC / 50/60Hz CV90-60859-1 120VAC / 60Hz Standard Battery: 3.6V / 900mAh Output 4.5V 1.5A 4.5V 1.5A 5.2V 400mA 093 453 037 Kyocera Wireless Corp. 10300 Campus Point Drive, San Diego, CA 92121 U.S.A. Visit us at www.kyocera-wireless.com To purchase accessories, visit www.kyocera-wireless.
CONTENTS 1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installing the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Charging the battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Getting to know your phone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Using menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
xvi 3 Entering Letters, Numbers, and Symbols . . . . . . . . . . . . . . . . . . . . Understanding text entry screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . Text entry modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Capitalization settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quick reference to text entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 34 34 38 39 4 Storing Contacts . . . . .
Using shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 Setting FunLights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 Personalizing the screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Creating a secure environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Setting message alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Race 21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doodler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . My Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . My Pictures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 113 115 116 10 Connecting to the Internet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 GETTING STARTED This document describes the Kyocera 3225 trimode phone, with CDMA digital service at 800 MHz and 1900 MHz, and analog service at 800 MHz. Your phone comes with an internal/removable lithium ion (LiIon) battery. Fully charge the battery before using the phone. Installing the battery 1. 2. Hold the phone face down Place the battery in the phone casing with the metal contacts facing the antenna end of the phone. 3.
Charging the battery The battery is partially charged when you receive your phone. You must have at least a partial charge in the battery to make or receive calls, regardless of whether or not the AC adapter is connected to the phone. To charge the battery, connect the AC adapter to the jack on the side of the phone (as shown), then connect the adapter’s plug to a wall outlet.
2. Hold the phone face down. Press down on the latch on the back of the phone and pull off the battery door. 3. Place your fingernail or the notch in the battery door under the tab on the battery and lift it out of the phone. Caring for the battery This section describes important safety information and tips for improving battery performance. General safety guidelines • • • • Do not take apart, puncture, or short-circuit the battery.
Common causes of battery drain The following functions drain the battery more quickly and adversely affect talk and standby times: • Playing games or using the Web frequently. • Frequent use of backlighting and/or FunLights. • Operating in analog mode. If you do not see a on the home screen, the phone is in analog mode. Your phone switches between modes to find the best signal.
Performing basic functions To... From the home screen... Turn the phone on Press Turn the phone off Press and hold appears. Make a call Enter the number and press End a call Press (the red key). Answer a call Press (the green key). Access voicemail Press and hold and follow the system prompts. Contact your service provider for details about their voicemail system. Verify your phone number Select Menu → Phone Info.
6 To... From the home screen... Lock the keypad Press and hold Access a contacts list Press Silence all sounds Press and hold Access your shortcuts Press left. down. right. up.
Getting to know your phone 1 Jack for Hands-free Headset (sold separately) only. 2 Home screen. Press 3 Jack for AC Adapter (included). 4 Stationary Antenna. 5 FunLightsTM make patterns when you turn on the phone or play games, and alert you to calls, text or voice messages, a scheduler reminder, or your alarm clock. Refer to page 77. 6 Jack for data cable (sold separately). to select Menu. Warning Inserting an accessory into the incorrect jack will damage the phone.
7 OK key selects a menu item or option. 8 Speakerphone key turns the speakerphone on and off. 9 Send/Talk key starts or answers a call. 10 Keypad for entering enter numbers, letters, or symbols. 11 * Shift key changes the text mode in text entry. 12 Clear key erases the last character in text entry, or returns to the previous menu. 13 Navigation key scrolls through lists and positions cursor.
Using menus The contents of the main menu are as follows: Messages Settings Fun & Games* Recent Calls Incoming Calls Voicemail Silent Mode TetrisTM Brick AttackTM Outgoing Calls Send New* Keyguard Missed Calls InBox Sounds Race 21TM Erase Lists Net Alerts* Display DoodlerTM OutBox* Voice Services My Sounds Contacts Saved Security My Pictures View All Erase Msgs Call Tools Add New Group Lists* Information Voice Memo Find Name Network Scheduler Add Voice Dial Msg Settings Convenience Alarm Clock Speed Dial Li
• Press left, right, up, or down to see menus.* • Press to select a menu or menu item. • Press up or down to view menu items. • Press to back up a menu level. • Press to return to the home screen. * Your menus may appear as graphics or as a list. To change the way they appear, select Menu → Settings → Display → Main Menu View, then select either Graphics or List and press . Note: In this guide, the use of an arrow → tells you to select an option from a menu.
Understanding screen icons Icons in the top row The phone is operating in CDMA digital mode. If phone is operating in analog mode. does not appear, the The phone is receiving a signal. You can make and receive calls. Fewer bars indicate a weaker signal. The traffic channel is in use. You can make and receive calls. The traffic channel is not available. You cannot make or receive calls. The phone is roaming outside of its home service area. You have a text message, voicemail, or page.
High-speed (3G) data service is available and active on your phone.* *For availability of high-speed data on your network, check with your service provider. High-speed data is not available on your phone. (Check with your service provider for availability.) High-speed data service is available, but the phone is dormant. (blinking) The phone is sending high-speed data. (blinking) The phone is receiving high-speed data.
Icons in the bottom row Keyguard is on. The keypad is locked. The phone is set to light up instead of ring. The phone is set to vibrate instead of ring. The phone is set to show its position location to your service provider as well as emergency services. The phone is set to show its position location to emergency services only. Enter text using eZiText rapid text entry. Enter text using normal alpha text entry. Capitalize the next letter during text entry. Capitalize every letter during text entry.
Enter symbols. Enter numbers. Other icons 14 Press up. Press down. Press left. Press right. Press to go back or clear an item. Press to select an item.
Outgoing call Incoming call Missed call (flashing) Forwarded call (Call type may not be available. Check with your service provider.) Three-way call (Call type may not be available. Check with your service provider.
2 MAKING AND ANSWERING CALLS Making a call 1. Make sure you are in an area where the signal can be received. Look for the symbol on the home screen. Note: The more bars you see in this symbol, the clearer the reception will be. If there are no bars, try to move to where the reception is better. In some cases, this can be as simple as changing the direction you’re facing. If your phone cannot locate a signal, it changes to power-save mode.
Redialing a number To redial the last number called, press prompting you to speak a name, press twice. If you see a message again. Calling a saved number If you have already saved a phone number, you can use the frequent contacts list to find it quickly. 1. Press down. This brings up a list of all saved contacts. Note: A list of frequent contacts will also appear at the top of the list if you have enabled the frequent contacts setting. For more information, see page 46. 2.
• • • To answer the call, press . If you do not wish to answer the call, Silence or Ignore and press . Silence mutes the ringer. Ignore mutes the ringer and returns you to the screen that was active at the time the call came in. Both actions will send the caller to voicemail if you do not pick up the call. To place the caller on hold momentarily until you can answer the call, press Hold. This will play a recorded message from you telling the caller he/she is on hold.
Select Menu → Settings → Convenience → Hold Call. Select Enabled. If you have not recorded a hold message, you will be prompted to record one. Example: “Please hold. I’ll answer in a minute.” 4. Record the message twice, as prompted. 5. Select Save, Play, or Exit. The next time a call comes in, you will have the option of placing it on hold. 1. 2. 3. Placing a call on hold You can place a call on hold once you have enabled the feature.
Changing the hold message To change your hold message: 1. Select Menu → Settings → Convenience → Hold Call → Re-record Msg. and follow the prompts. 2. Record the message twice. 3. Select Save, Play, or Exit. Using the speakerphone You can turn the speakerphone on at any time. • To turn the speakerphone on, press . • To answer an incoming call and turn speakerphone on at the same time, press . • To turn speakerphone off, press . Adjusting speakerphone volume 1. 2. 3.
Dealing with missed calls When you have missed a call, “Missed” appears on your screen. This message remains, unless the caller leaves a voicemail. • Press or to clear the screen. • To view the caller’s number or name, select Calls. In the Recent Calls list, the missed call is indicated with a flashing . • If the caller left a voicemail message, select Call. If you have not yet set up your voicemail, the caller cannot leave a message. For help setting up voicemail, see page 25.
Viewing recent call details Details on the last 29 calls you made or received are stored in the Recent Calls list. You can get details on the caller’s name and phone number, along with the time and length of the call. Icons indicate the types of calls in the list. Outgoing call Forwarded call Incoming call Three-way call Missed call (flashing) Viewing recent calls 1. 2. 3. 4. 22 Select Menu → Recent Calls. Select a list: Incoming Calls, Outgoing Calls, or Missed Calls. Select a recent call item.
– View Contact—Show details on the contact if the caller’s information is already in your Contacts directory. Note: If the number has been saved as “secret,” you must enter your four-digit lock code to view or edit the number. For information on the lock code, see “Changing your lock code” on page 83. To classify a phone number as secret, see “Saving a phone number” on page 41. Erasing recent calls 1. 2. 3. Menu → Recent Calls → Erase Lists.
To speed dial From the home screen, enter the one- or two-digit speed dialing location and press . Setting up 1-Touch Dialing 1-Touch Dialing is a form of speed dialing that allows you to press and hold a speed dial location to make a call. It is the fastest way to speed dial. 1. Select Menu → Settings → Convenience → 1-Touch Dialing → Enabled. 2. Press . Using 1-Touch Dialing To dial a phone number, simply press and hold the assigned speed dialing location for the phone number.
5. 6. 7. Highlight the number to remove. Press right to highlight Remove. Press . Setting up voicemail Before your phone can receive voicemail messages, you must set up a password and record a personal greeting with your service provider. When you have set up your voicemail, all unanswered calls to your phone are automatically transferred to voicemail, even if your phone is in use or turned off. 1. From the home screen, press and hold . 2. Enter your passcode, which you obtain from your service provider.
Checking voicemail messages When a voice message is received, your screen will display text similar to: “New Message 1 Voicemail.” This text remains for about five minutes. After that, look for the symbol at the top of your screen. The symbol flashes if the message is urgent. If you see “New Message” on your screen 1. Press to select Voice. This initiates a call to your voicemail number. 2. Follow the prompts to retrieve the message.
Silencing an incoming call • To silence an incoming call quickly, press . Then press to answer the call. This action silences the current call only. The next call will ring as normal. Adjusting the volume during a call • To adjust the earpiece volume during a call, press up or down. Locking the keypad The Keyguard locks your keypad to prevent accidental keypresses when the phone is turned on and a call is not in progress. You can still answer or silence an incoming call.
Keeping track of your calls Your phone has two timers that count the amount of calls you have made and received. All calls This timer displays the total number and duration of all calls you have made and received. You cannot reset this timer. • Select Menu → Settings → Call Information → All Calls Timer. Recent calls This timer displays the total number and duration of recent calls you have made and received since the last time you reset the timer. 1.
Receiving data or faxes Your phone may be able to receive certain data or faxes, depending on the system sending the information. To receive data or faxes, you must connect the phone to a laptop or PC (see page 88), and switch the phone from voice mode to data/fax mode. Note: You cannot receive voice calls while the phone is in data/fax mode. 1. Select Menu → Settings → Network → Data/Fax Calls. 2. Press to select an option: – Voice only—Allows only voice calls.
Emergency numbers Designating emergency numbers The emergency numbers feature allows you to specify three personal phone numbers that can be called when the phone is locked. To designate emergency numbers: 1. Select Menu → Settings → Security. 2. Enter your four-digit lock code. 3. Select Emergency #’s. 4. Select an Unassigned slot. 5. Enter the phone number, including the area code. Note: Do not enter 1 before the area code. 6. Press to select Done.
• • To make a call to an emergency number from a locked phone, you must dial the number (including area code) exactly as it was stored in Emergency Numbers. Your phone does not enter Emergency mode when you dial an emergency number you have designated in the phone. Calling emergency numbers To call 911 • Dial and press . You can call 911 even if your phone is locked or your account is restricted. However, when you call, your phone enters Emergency mode.
Note: To determine who has access to your location, see “Setting position location” on page 90. Understanding roaming Controlling network roaming This setting allows you to force the phone into either digital or analog mode. This is useful if you are in an area that borders on digital service and the automatic feature is causing the phone to keep switching between modes. 1. Select Menu → Settings → Network → Digital/Analog. 2. Select an option and press .
– – – – Disabled will not alert you when you roam outside your home service area. When no svc alerts you with three tones decreasing in pitch when service is lost and three tones increasing in pitch when service is acquired again. Roam Change alerts you with two tones decreasing in pitch when roaming service is acquired and three tones increasing in pitch when home area service is acquired again.
3 ENTERING LETTERS, NUMBERS, AND SYMBOLS You may enter letters, numbers, and symbols in contacts, text messages, and other functions; for example, when you create a personal banner for your phone’s home screen. For a quick reference to text entry, see page 39. Understanding text entry screens The text entry area is a large field in the center of the screen. The current text entry mode (and capitalization setting, when applicable) are indicated by icons at the bottom of the screen.
Note: The mode you start in depends on the task you are doing. For example, when entering a phone number, you’re in number mode. When entering a name for a contact, you’re in normal text mode. Entering numbers You can enter numbers in several modes. • To enter a number while in mode, press a number key once. • To enter a number while in or mode, press and hold a number key until the number appears on the screen. Entering words letter by letter Use normal text mode to enter letters. 1.
Entering words quickly When you press a series of keys using mode, checks its dictionary of common words and guesses at the word you are trying to spell (available for English only). 1. For each letter of the word you want, press the key once. For example, to enter the word “any” press: → → . 2. If the word doesn’t match what you want, press to look at other word matches. 3. When you see the word you want, press .
Entering symbols While entering text, you can also enter symbols by pressing until you see the symbol you want. Using this method, you have access to the following symbols: . & @ , - ‘ : ; ? / “ ( ) _ To access the full set of symbols: 1. Press right to highlight the current mode and press to enter the menu. 2. Select Symbols. 3. Press down to view the list of symbols. 4. Press the number key corresponding to the symbol you want.
• Press right to highlight the current text mode, press menu, then select a different mode. to enter the Capitalization settings Three capitalization settings are available in and modes: Capitalize next letter Capitalize every letter Capitalize first letter of every word (in a contact) or sentence (in a text message) If no icon appears, all letters will be in lower case. To change capitalization settings: • Press until the icon for the setting you want appears.
Quick reference to text entry This table gives general instructions for entering letters, numbers, and symbols. To... Do this... Enter a letter Use mode and press a key until you see the letter you want. For more information, see page 34. Enter a number Use mode and press a key once to enter its number. For more options, see page 34. Enter a symbol Use mode and press until you find the symbol you want. See page 37.
Capitalize every letter In mode, press . Choose . Capitalize the first letter of each word In mode, press . Choose . Highlight an option at the bottom of the screen Press 40 left or right.
4 STORING CONTACTS Use your phone’s Contacts directory like a set of phone index cards to store information about a person or company. Your phone can hold, on average, about 200 phone numbers. Saving a phone number To save a phone number or pager number, take these steps. 1. From the home screen, enter the phone number you want to save. 2. Press to select Save New. 3. Enter a name for the contact. If you need to learn how to enter letters, see page 34.
– 4. Add Voice Dial—Speak the name of the contact person for this number so that you can dial it using voice recognition (VR). For more information, see page 94. – Speed Dialing—Select a speed dialing location from the list. – Secret—Select Yes to lock the phone number. If a phone number is locked, you must enter your four-digit lock code (see page 83) to view or edit the number. – Primary Number—Classify this number as the primary number for the contact.
– 4. 5. A Hard Pause causes the phone to stop dialing until you select Release. Enter the remaining numbers. Select Save New. Saving an email address, street address, URL, or note To save an email address, street address, Web page URL, or note as a new contact, follow these steps. To add one of these items to a saved contact, see “Editing or erasing a contact” 1. Select Menu → Contacts → Add New. 2. Highlight Phone Number, Email Address, Street Address, URL, or Note and press to select it. 3.
Editing or erasing a contact 1. 2. 3. 4. 5. 6. 7. Select Menu → Contacts. Select View All or Find Name to find the contact you want to edit. Highlight the contact to edit and press . Select Options. Highlight an option and press to select it: – Add New to add a phone number, email address, street address, Web page URL, or note. – Erase Contact to erase the entire contact. – Edit Name of the contact. – Classify Contact as personal or business. Enter the new information. Press to select Save.
5. Highlight an option for the phone number and press : – Send Text Msg—Send a text message to the phone number you selected. – View Number—See the phone number you selected. – Add Voice Dial—Speak the name of the contact person for this number so that you can dial it using voice recognition (VR). For more information, see page 93. – Speed Dialing—Select a location to use for speed dialing the number. – Edit Type—Assign a type: work, home, mobile, pager, or fax.
6. 7. Enter the new information and follow the prompts. Press to select Save, if necessary. Finding contact information There are three main methods for finding a phone number or contact details: (1) checking the frequent contacts list, (2) searching the Contacts directory, and (3) using Fast Find. Checking the frequent contacts list From the home screen, press down to see the last 15 of your most frequently called contacts, in order from most frequent to least frequent.
Searching the Contacts directory 1. 2. 3. Select Menu → Contacts. Select a search method: – To view a complete list of your contacts, select View All. – To locate a specific name, select Find Name. Enter part of the contact name, then select Find. Scroll down until you find the name you want. – To call the contact, select the number and press . – To display the full contact, press . Setting Fast Find With Fast Find, you press one or two keys to view close matches of the number you are looking for. 1.
Using Fast Find 1. From the home screen, press the keys corresponding to the letters of the name you want to find. The matching contacts appear on the screen. Note: Speed dial locations appear before names if they use the same keys. For example, to look for Abe’s contact entry, press for “A”. Because there is a speed dial location associated with 2, the speed dial contact assigned to 2 appears first. To find Abe’s number, you would again press , the key that corresponds to the next letter of his name. 2.
5 SENDING AND RECEIVING TEXT MESSAGES This chapter describes how to send, receive, and erase text messages from your phone. For information on voicemail messages, see page 25. Important: The features and menus described in this chapter may vary depending on services available in your area. In addition, usage charges may apply to each message. For clarification on these issues, check with your service provider.
(Check with your service provider for availability of options.) Sending a simple message To send a plain text message to a single recipient: 1. Select Menu → Messages → Send New. 2. Choose a method to enter the recipient’s phone number or email address: – Select a saved number from the Recent List or Contacts List. -or– Enter a New Address manually. To enter letters, press right, then press to switch to mode. To enter “@” from mode, press repeatedly until the symbol appears.
Understanding appended messages Text entry field Character Message counter A single message can contain up to 123 characters. If you go over this character limit, the phone may automatically append an empty message to make space. Note that your service provider will charge for your first message as well as each appended message. In the Message entry screen, two counters keep track of the characters and appended messages (if available from your service provider).
indicates that three messages have been appended together. Important: Your service provider will charge you for each message, so if the counter shows 3/10, you will be charged for three messages. Including pictures and sounds Depending on the services available from your carrier, you can include smiley faces, graphics, and sound in your text messages. To send a message with special features: 1. Select Menu → Messages → Send New. 2.
3. 4. 5. 6. To add another recipient to this message, enter a space or comma after the first number or email address. Then enter another recipient manually or select Options → Contacts. Note: You can send a message to up to 10 contacts at once. The messages will be sent one at a time, once to each addressee. When you are done entering addresses, highlight Next and press . Enter the message.
– 7. AutoText —Select a prewritten message. Highlight one from the list and press to select Insert. (To edit or create new prewritten messages, see page 66.) – Contacts—Add information about a saved contact. Highlight the contact from the list and press to insert it. When you have completed the message, you can send it immediately or set sending options. To send it immediately, press to select Send. To set sending options, see the following procedure.
– – – – – – – – Select an unused reply, enter the reply text (up to 14 characters), and select Done. – When all replies have been entered, select Done twice. Your replies are saved and can be used in other messages. Add Address—Return to the “To” screen to add another recipient without losing the message text. Enter the new address, then select Next to return to the message entry screen. Msg Receipt—Request notification when the message has been received.
2. 3. When you have finished setting options, press window. Highlight Send and press . to return to the message Sending a saved message You can reuse a message you have stored in your Saved folder. 1. Select Menu → Messages → Saved. 2. Press up or down through the list of messages and press to select one. 3. Highlight an option and press : – Resume—Modify or send the message. – Send To—Add another recipient. – Erase—Erase the saved message. – Done—Return to the Saved folder. 4.
If you cannot send messages You may not be able to send or receive messages if your phone’s memory is nearly full, or if digital service is not available at the time. To free up memory, erase old messages. See “Erasing messages” on page 62. Receiving incoming calls while creating messages • • If you don’t wish to answer the call, select Ignore. To answer the call, press . The message you were working on will be saved in the Saved folder.
The scheduled message will be sent at the scheduled time. You cannot cancel delivery of the message. The message cannot be sent because service is not available. An alert appears on your phone if the message cannot be sent. The scheduled message has been sent and will be delivered as scheduled. You cannot cancel delivery of the message. The message has been received by the recipient you specified. The message has been received and opened by the recipient you specified. (This symbol may not be available.
Saving messages to the OutBox You can have messages saved to the OutBox automatically. Note: The OutBox is useful for checking the status of messages you have sent. Messages should be erased from the OutBox periodically to conserve memory in the phone. If you are looking for a place to save a message so that you can send it again, use the Saved folder. For more information, see page 55. 1. Select Menu → Messages → Msg Settings → Save to Outbox. 2.
If you see the “New Message” note You can choose to: • View the message—Press . • Ignore the message—Press right and press • Clear the screen—Press . . If you see the body of the message The body of an incoming message will appear on your home screen only if your phone is set to Direct View. To set Direct View, see page 67. You can choose to: • Ignore the message—Press . • Read the message. See “Reading the message” on page 61.
2. 3. Press Press up or down to scroll through the list of messages. to read a message. Reading the message The options available to you may vary. Check with your service provider. Note: Sounds embedded in text messages will not play if the phone is set to Silence All mode. 1. If the text message is long, press down to view the entire message. 2.
– Save as AutoText to save the text from the message as AutoText, which you can insert into other messages. Graphics and sound will not be saved as part of AutoText.(For more about AutoText, see page 66.) – Block the sender’s address so that your phone will not receive any more messages from it. 3. Select Done. Note: The symbol indicates: • A graphic did not come through. It may be too large or incorrectly formatted. • An appended message is missing. (For more about appended messages, see page 51.
Erasing single messages 1. 2. 3. 4. 5. Select Menu → Messages. Press down and press to select the type of text message you want to erase (InBox, OutBox, or Saved). Press to select the message to erase. Select Erase to erase the message. A notification appears: “Erase this message?” Select Yes to erase the message. Note: You can erase a scheduled message from the OutBox, but you cannot cancel delivery of the message. Erasing all messages 1. 2. Select Menu → Messages → Erase Msgs.
3. A message appears: “Erase all messages?” Select Yes to erase messages or No to cancel. Erasing messages automatically Use this setting to have old messages automatically erased from the InBox when memory is low. 1. Select Menu → Messages → Msg Settings → Auto-Erase. 2. Press to select Old InBox Msgs. Customizing message settings To make messaging easier, you can customize settings for sending and receiving messages. Creating group lists You can create and save a list of multiple recipients.
– Recent List—Select numbers from your Recent List. Highlight the number or contact name and press . The phone number appears in the address field. – New Address—Enter the phone number or email address yourself. To enter letters, press to switch to mode. To enter symbols, press until you find the symbol you want. For more information on text entry modes, see page 34. -or- -or– 5. 6. 7. Contacts List—Select contacts from your phone book. Highlight the contact and press twice.
Creating and editing prewritten messages (AutoText) Your phone comes with prewritten (AutoText) messages, such as “Please call me,” which you can insert into the body of a text message. You can edit these messages and create new ones. Your phone will store up to 20 AutoText messages, with up to 100 characters per message. 1. Select Menu → Messages → Msg Settings → Edit AutoText. 2. To create a new pre-written message, highlight New AutoText and press .
Opening messages automatically (Direct View) With Direct View, you can set your phone to open incoming text messages and display them on the home screen as soon as the phone receives them. Note: Messages will not appear on the screen if the phone is in use. 1. 2. Select Menu → Messages → Msg Settings → Direct View. Select Enabled.
5 CUSTOMIZING YOUR PHONE The contents of the Settings menu are as follows. Silent Mode Keyguard Sounds Ringer Volume Ringer Type Business Ring Personal Ring Roam Ringer Earpiece Volume Key Volume Key Length Missed Call Smart Sound Minute Alert Spkrphone Vol. Display Backlighting My Banner FunLights 68 Display (Con’t) Call Information Messaging Main Menu View Screen Saver Auto-Hyphen Language Time Format Contrast Recent Calls Timer All Calls Timer Browser Timer Voicemail Num.
Setting vibrate mode You can set your phone to vibrate or to vibrate and then ring when you receive an incoming call. 1. Select Menu → Settings → Silent Mode. 2. Choose an option and press : – Vibrate Only—Causes the phone to vibrate for the duration of the incoming call alert. – Vibe then Ring—Causes the phone to vibrate for the first 10 seconds and then ring for the remainder of the incoming call alert. – Lights Only—Causes the screen and keys to light up and flash for the duration of the call alert.
Silencing all sounds Your phone is set to ring for incoming calls and to beep to indicate alerts (such as new messages) and movement through the menus. There is a quick way to silence all sounds and set your phone to vibrate and light up to indicate incoming calls and alerts. To silence all sounds • From the home screen, press right and hold. A appears on the screen, indicating the phone has silenced all sounds and is in vibrate mode.
3. Press to save your selection. Note: To set the FunLights on both sides of the screen to light up, see “Setting FunLights” on page 77.
Turning sounds back on • The quickest way to turn sounds back on is to press You can also use menus: 1. Select Menu → Settings → Silent Mode. 2. Select Normal Sounds. 3. Press to save your selection. right and hold. Choosing a different ringer Your Kyocera 3225 phone has 25 ringers you can choose from for your incoming calls. 1. Select Menu → Settings → Sounds → Ringer Type. 2. Scroll down the list to hear the different rings. 3. Press to select a ringer from the list.
3. Select a ringer from the list. Note: You can also set FunLights to notify you of business and personal calls. See page 77. Importing additional ringers You can import additional ringers into your Kyocera 3225 phone using the Kyocera Phone Desktop software (sold separately). To purchase this software and other accessories, visit www.kyocera-wireless.com/store. You may be able to download ringers over-the-air. Check with your service provider for availability.
Adjusting the ringer volume 1. 2. Select Menu → Settings → Sounds → Ringer Volume. Press right to increase the volume, or left to decrease the volume. Adjusting the speakerphone volume To adjust the speaker volume: 1. Select Menu → Settings → Sounds → Spkrphone Vol. 2. Press . 3. Press up or down to find the level. 4. Press to save the setting. Changing the key tones You can change the volume and duration of the tones the phone makes when you press the keys.
Using shortcuts From the home screen, you can access shortcuts by pressing the navigation key in different directions. Three shortcuts are automatically programmed into your phone (left, right, and down). For the fourth direction (up), you can set a shortcut to one of the features of your phone. Defining the “up” feature shortcut When you define a feature shortcut, you are able to bypass the menu selection and scrolling and need only press up to launch the screen of the function you choose. 1.
– – – – – – – BREW Apps* (dependent on availability from service provider) Web Browser Stopwatch Calculator Voice Memo Scheduler None to disable this shortcut Using the up feature shortcut • From the home screen, press and hold up. Creating a shortcut to your frequent contacts list By default, your phone lists your entire contacts list when you press down. You can set the phone also to show a list of your most frequent contacts. 1. Select Menu → Settings → Convenience → Frequent List. 2.
Setting FunLights Your Kyocera 3225 has FunLights that frame your phone’s screen. FunLights have six different patterns you can choose from to display when you play games, make calls, receive calls and text messages, and when your alarm clock and scheduler notify you of events. To set the FunLights: 1. Select Menu → Settings → Display → FunLights. 2. Press to select FunLights for: – Incoming calls—Lights when phone rings or vibrates.
– – Alarm Clock—Lights when the alarm clock beeps. BREW—Lights when you use BREW. (Dependent upon services available from your service provider.) – Games—Lights when you play games. (Dependent upon services available from your service provider.) You cannot select light patterns for games. Select Disabled or Enabled and press . 3. Press up and down to scroll through the light patterns: Intense, Roller Coaster, Blast Off, Landing, Tango, and Wave. Each pattern displays as you highlight it. 4.
Personalizing the screen Changing your banner The banner is the personal label for your phone. It appears on the home screen above the time and date. The banner can be up to 14 characters long. 1. Select Menu → Settings → Display → My Banner. 2. Select Edit. 3. Press to clear the screen. 4. Enter your new text. 5. Press to save. Setting a screen saver Several screen savers are provided with your phone. A screen saver works only from the home screen, and activates 10 seconds after the last keypress.
3. Press to return to the home screen and wait 10 seconds to view the screen saver you chose. Note: You can add graphics you have created or saved to the Screen Savers list. Refer to See “My Pictures” on page 116. Choosing a different time/date format 1. 2. Select Menu → Settings →Display → Time Format. Highlight the option you want. Choosing a different menu view You can change the appearance of the menus you see when you select Menu from the home screen. 1.
2. Press to return to the home screen. The next time you press will see the menu view you selected. , you Adjusting the backlighting Your screen lights up while you are in a call or when you press a key on the keypad. However, you can change when and how backlighting lights up. 1. Select Menu → Settings → Display → Backlighting. 2. Select an option from the list: – Disabled—Turns backlighting off. – 5 seconds—(Default) Turns backlighting on for 5 seconds after your last keypress.
– 30 sec. & in call—Turns backlighting on during a call, and for 30 seconds after your last keypress. Note: Keeping backlighting on during a call drains the battery more quickly and reduces talk and standby times. Setting power backlighting You can set backlighting to remain on when an external power source, such as the AC adapter, is used with the phone. Note: Power backlighting may not be available with some accessories. Check with your service provider. 1. 2.
Setting numbers to auto-hyphenate Auto-hyphenation is a setting that automatically inserts hyphens into your phone numbers to be consistent with the U.S. dialing plan. For example, 1-222-333-4444. • Select Menu → Settings → Display → Auto-Hyphen → Enabled. Choosing a different language Your phone may support languages in addition to English. 1. Select Menu → Settings → Display → Language. 2. Select a language, and press .
3. Select Yes, enter a new four-digit code, then press code again. . Enter your new lock Locking your phone When your phone is locked, you can call only emergency numbers or your service provider number. You can still receive incoming calls. 1. Select Menu → Settings → Security. 2. Enter your four-digit lock code. 3. Select Lock Phone. 4. Highlight an option: – Never—Does not lock the phone. – On power up—Locks the phone every time you turn it on. – Now—Locks the phone immediately. 5. Press .
Restricting calls You can restrict the calls that can be made from your phone to only those that have been saved in your Contacts Directory. 1. Select Menu → Settings → Security. 2. Enter your four-digit lock code. 3. Select Limit Calls Out. 4. Select Contacts Only. Erasing all contacts You can erase all contacts from the Contacts directory. 1. Select Menu → Settings → Security. 2. Enter your four-digit lock code. 3. Select Erase Contacts. 4. Select Yes to erase all contacts.
1. 2. 3. 86 Select Menu → Settings → Messaging → Alerts. Select the type of alert: Message, Net, Page, or Voicemail. Press to select an option: – Disabled—Does not alert you when a message is received. – Vibrate Once—Sets the phone to vibrate once when a new message is received. – Vibe & Remind—Sets the phone to vibrate once when a new message is first received, and once every five minutes. To stop the reminder, press to select Ignore.
Setting alerts for your headset When a headset (sold separately) is attached to the phone, you can set alert sounds to originate from the headset. 1. Select Menu → Settings → Accessories → Headset Ring. 2. Select Out of headset to have alerts originate from the headset. Switching between phone lines Your phone can have two service accounts, or phone lines, associated with it. Each phone line has its own phone number. When you are using one line, you cannot receive calls from the other.
Data settings Connecting to a laptop or a PC The Com Speed sets the data rate at which your phone connects to a laptop or PC, or at which it sends and receives over-the-air text messages. 1. Select Menu → Settings → Accessories → Com Speed. 2. Select the speed. The options are: 19.2 kbps, 115.2 kbps (default), 230.4 kbps. Note: There may be a higher charge for making calls using high-speed data in areas where 1X service is available. Check with your service provider for details.
Setting the phone to receive data or faxes Your phone may be able to receive certain data or faxes, depending on the system sending the information. To receive data or faxes, you must connect the phone to a laptop or PC and switch the phone from voice mode to data/fax mode. Note: To purchase a cable, you can contact your service provider or purchase one from us at (800) 349-4188 (U.S.A. only) or (858) 882-1410, or online at www.kyocera-wireless.com/store. 1. Connect the phone to the laptop or PC.
– Data, until off—Force the phone into data mode until the phone is turned off. Note: You cannot receive voice calls while the phone is in data/fax mode. Setting position location This setting allows you to share your location information with network services other than emergency services, such as 911, in markets where service has been implemented. Note: This feature works only when your phone is in digital mode. You do not have the option of turning off the locator to emergency services.
6 USING VOICE RECOGNITION Voice recognition is a unique feature on your Kyocera 3225 phone that allows you to make and answer calls by speaking commands into the phone’s microphone. Note: You cannot use voice recognition to end a call; you must press . Setting up voice dialing To make or receive calls using voice recognition (voice dialing), contacts must be saved and have associated voice commands, or voice tags.
Adding a voice tag to a new contact This procedure allows you to create a contact before adding a voice tag to it. 1. From the home screen, enter the phone number of the person you want to call. 2. Press to select Save New. 3. Enter a name for the contact and press to save. For help entering letters, see page 34. 4. Press right and select Options. 5. Select Add Voice Dial. 6. At the tone or prompt, say a name, then repeat the name as instructed.
Adding a voice tag to an existing contact This procedure allows you to choose a contact from your list before adding a voice tag to it. 1. From the home screen, select Menu → Contacts → View All. 2. Highlight the contact you want to add voice tag to and press . 3. Highlight the phone number and press . 4. Select Add Voice Dial. 5. Follow the prompts to record a name. 6. Press to return to the home screen. You are now ready to make a call using this voice tag.
5. Follow the prompts. Calling using voice tags 1. 2. 3. 4. 5. If you haven’t already done so, record a voice tag for the person you wish to call. See “Setting up voice dialing” on page 91. From the home screen, press . The phone responds: “Say a name or say dial.” Say the name of the person you want to call. If the name you said matches a contact in the Voice Dial List, the phone responds: “Calling (Name).” Remain silent to make the call, or say “No” to cancel.
To enable Expert Mode: 1. Select Menu → Settings → Voice Services → Expert Mode. 2. Select Expert. To make a call using Expert Mode: 1. Press and wait for the beep. 2. Say the name or the speed dial number of the contact you want to call. Making calls using digit dialing When using digit dialing, you speak digits to dial a phone number. Note: You cannot speak a string of digits. You must speak one digit at a time and wait for the prompt. 1. From the home screen, press .
– – – – Say “Call” to dial the number. Say “Verify” to cause phone to repeat the set of digits that you input. Say “Cancel” to exit voice recognizer and return to the home screen. Speak a digit to enter the next digit. Once the phone repeats the digit, you can speak the next digit or pause to hear the prompt.
2. Select Menu → Settings → Keyguard → Disabled, then press . To wake up the phone: 1. Say “Wake Up” and listen for a tone. 2. Say “Wake Up” again until you hear two tones. If the phone does not recognize your “Wake up” command, see “Training voice recognition” on page 98.
2. Select Disabled. To activate the Voice Answer setting: 1. Select Menu → Settings → Voice Services → Voice Answer. 2. Highlight Enabled, then press 3. Select Menu → Settings → Sounds → Call Ring/Vibe → Ring only. 4. Press .
5. Follow the prompts for each word until training is complete. Note: The “Wake up” command can only be used with a hands-free car kit or headset (both sold separately). See page 96. Ignoring an incoming call To ignore an incoming call, do one of the following: • Say “No” and press to silence the alert. • Remain silent. The voice alert repeats twice and the phone rings once, then returns to the home screen.
7 USING TOOLS Voice Memo The Voice Memo tool allows you to record and play back audio memos. Shortcut: You can access voice memo quickly by setting up a shortcut. See “Defining the “up” feature shortcut” on page 75. Functions Play Fast forward Pause NAME Name the memo Stop ERASE Erase a memo Rewind Recording a voice memo 1. 2. 100 Select Menu → Tools → Voice Memo → Record New. The phone says: “Please record at the tone.” Say your memo and select when finished.
– 3. To save a name for your memo, press right and select Name. You may enter up to 12 characters. Memos saved without names are saved as “Memo 1”, “Memo 2”, etc. Press to select Save. Playing a voice memo 1. 2. 3. 4. Select Menu → Tools → Voice Memo. Highlight the memo you want to hear. Press . Highlight and press . Rewind and fast forward To rewind or fast forward a voice memo while it is playing, select or to fast forward. to rewind Naming a saved voice memo 1. 2. 3. 4.
Erasing a saved voice memo 1. 2. 3. 4. Select Menu → Tools → Voice Memo. Highlight the memo and press . Press right to highlight Erase. Press and follow the prompts. Scheduler The Scheduler allows you to schedule events, such as meetings or appointments, and keep track of annual occasions, such as birthdays or wedding anniversaries. Adding an event Events are placed on the calendar at the time you select. 1. Select Menu → Tools → Scheduler. 2. Find the day for the event and press .
4. 5. 6. 7. 8. Enter a name for the event. For help entering text, see page 34. Press when you are done entering letters. Select Next to set the event Start time, Duration, and Alarm. – Press up or down to select hour, minutes, and timing of alarm. – Press left or right to move between fields. Press to select Next. Add a note to the event and press or press twice to finish. Adding an occasion Occasions are placed on the calendar at the beginning of the day you select.
5. Press to add the occasion. Viewing, editing, or erasing an event 1. 2. 3. 4. 5. Select Menu → Tools → Scheduler. Select View Day or View Month to find the event you want to view, edit, or erase. Press up, down, left, or right to highlight an event and press to select it. Press right and press to select Edit, Erase, or New. Follow the prompts. Press to return to the home screen or to return to scheduler options. Viewing a list of occasions 1. 2. 3. 4.
Alarm Clock Use the Alarm Clock to set an alert for a specific time. The alert occurs only if the phone is on. 1. Select Menu → Tools → Alarm Clock → Set. – Press up or down to select an hour and minutes. – Press left or right to switch between hours, minutes, and a.m./p.m. – Use the phone keypad to enter numbers. 2. Press to select Done and save the setting. 3. When the alarm rings, select Off to turn off the alarm or Snooze to silence the alarm for 10 minutes.
6. Enter the number of guests and press calculated. . The amount each guest pays is Calculator Use the calculator for basic mathematical equations. 1. Select Menu → Tools → Calculator. 2. Use the keypad to enter numbers. 3. Press to select mathematical operations. = equal + add x multiply ÷ divide - subtract . decimal point C Clear all numbers entered and display a zero. MR Display the value currently stored in memory. M+ Add the displayed digit to the value stored in memory.
Clear one function or one digit from the screen and return the calculator to digit entry mode. Hold down to clear all of the digits and operations and display a zero. Exit the calculator and return to home screen. Timer This timer counts down for a specified amount of time. It beeps when that amount of time has elapsed. 1. Select Menu → Tools → Timer. 2. Press to Set. 3. Press up or down to set the hours, minutes, and seconds. To move the cursor, press left or right. 4. Select Start to begin the countdown.
Stopwatch 1. 2. 3. 4. 108 Select Menu → Tools → Stopwatch. Select Start to have the stopwatch begin counting. Select Stop to stop counting. Select Reset to set the counter back to zero and begin counting again. Press when finished.
8 FUN & GAMES Your Kyocera 3225 phone comes with games, a doodler, and storage for downloaded sounds and pictures. The games described in this chapter may be available on your phone. Check with your service provider for availability. If you receive an incoming call alert while you are playing Tetris™, Brick Attack™, or Race 21™, the game is paused and exited. You can return to play once the call alert ends. Games do not remain paused if the phone is turned off or loses power.
– – – – New Game—Initiates game play. To pause the game, press or . Pressing returns you to the menu where you can Continue Game to resume or choose from the other available options. Resume Saved—Returns you to the game you were last playing. Scoreboards—Displays the top five scores for the different game variations, including No Time Limit (default), Timed 2 Min, Timed 3 Min, Timed 5 Min., and Garbage. Settings—Choose a level of play, sounds, and game type: – Starting level—Choose a level of play.
Rotate Clockwise , , or Move Right or right Soft drop the tile or down up Return to Tetris menu Pause Brick Attack The goal of this game is to eliminate bricks arranged in levels. To do this, you send a moving ball upward using a paddle at the bottom of the screen. 1. Select Menu → Fun & Games → Brick Attack. 2. Press to select Yes at the prompt, “Turn off backlight to conserve battery?” 3. Press to select New. – To pause the game, press , then press to Resume.
Race 21 This game is a timed variation of Blackjack. Each game comprises three 90second rounds. To score points, add cards in each of the four columns, trying to reach but not exceed 21 in each column within during the course of the game. To play: 1. Select Menu → Fun & Games → Race 21. 2. Press to select Yes at the prompt, “Turn off backlight to conserve battery?” 3. Select New Game. The first card to be placed is shown at the top left of the screen.
4. 5. 6. 7. Continue placing cards until you are satisfied with your selections. – You can pause or end the game at any time by pressing . – You lose points each time you exceed 21 in a column. – Remember, there is a time limit! – Select Skip to skip one card per round. Press to select to get your score and advance to the next round. Select an option and press to select it. – New Game—Initiates game play. To pause the game, press . From here you can choose Resume, New or Quit.
2. 3. 4. 5. 6. 7. 114 Press to select Yes at the prompt, “Turn off backlight to conserve battery?” Select New Doodle to open the Doodle screen. Other options available are: – Resume Doodle opens the last doodle if available in memory. – My Pictures lists your existing doodles. – Instructions provides you with details on using Doodler. Select a drawing style. With Tools highlighted, press repeatedly to cycle through the options.
My Sounds Your Kyocera 3225 phone contains 10 preset sounds, which you can add to outgoing text messages. (Check with your service provider for availability.) To access stored sounds: 1. Select Menu → Fun & Games → My Sounds. 2. Press up or down to scroll through the sounds. 3. Highlight an option and press to select it: – Play allows you to listen to the sound. – Send opens a new message entry screen. – Assign allows you to use the sound as a ringer on your phone.
My Pictures Your phone can store 25 graphics. The My Pictures menu stores graphics you have created using the Doodler or received via text messaging. It also includes predefined graphics for your use. Note: All downloaded graphics are also stored in the Screen Saver menu. To view, edit, or erase graphics: 1. Select Menu → Fun & Games → My Pictures. 2. Press up or down to scroll through the graphics. 3. Highlight an option and press to select it: – Send opens a new message entry screen.
9 CONNECTING TO THE INTERNET Using the Web Browser You can use your phone to browse the Internet if you have obtained phone Internet services from your service provider and if over-the-air Internet access is available in your area. Note: You cannot receive incoming calls while you are using the Web Browser. Starting the Web Browser 1. Select Menu → Web Browser. A message informs you that airtime fees apply for browser use. For more information about how airtime is charged, contact your service provider.
4. Notes: – A appears in a secure session. – An underline and an arrow indicate that there is more text. Press down to view more text. Press to return to the previous screen. – For information on the menu options at the bottom of the screen, see “Using the Web menu options” on page 118. – For help searching for a Web site, see “Searching for a Web site” on page 119. When you have finished using the Internet, press to exit the browser.
– – UP.Link selects a different browser server. You can use this option if you have more than one Web Browser account, such as one for business and one for personal use. Restart restarts the Web Browser. Searching for a Web site How you search for a Web site depends on your service provider. However, most providers place search engines on the home page. For more information about searching for a Web site, contact your service provider.
4. A list of bookmarks appears. Enter the number corresponding to the bookmark you want and press . Checking Net alerts When alerts are received from a Web site, they are sent to your Net Alerts inbox. 1. Select Menu → Messages → Net Alerts. This action launches the browser inbox. 2. Press to accept browser fees. 3. Select the alert you want to read, and follow the prompts.
Changing the Web prompt You can choose to receive a confirmation prompt whenever you start or exit the Web Browser. 1. Select Menu → Settings → Convenience → Web Prompt. 2. Highlight an option and press to select it: – At Start confirms that airtime fees will be applied when you use the browser. – At End verifies you want to exit the browser. – Both prompts you when you start the browser and exit the browser. – No Prompts does not use any prompts.
For more information For more information about BREW capabilities and application pricing, contact your service provider. How does BREW work? You connect to the server, download applications, and then manage them as you like. When you choose an application, you have the option of choosing a demo, various limited use options, or the full version—all varying in price. If you choose a demo, BREW will let you know when it has expired. If you choose a priced version, the amount is added to your phone bill.
5. 6. Select Start. When a connection to the server is made, the BREW Shop menu appears with a list of application types to choose from. Select an application type. A full list of applications of the type you selected appears. New apps are indicated by an arrow on the left. Note: Long titles scroll left as you highlight them. 7. Select an application. A list of usages appears. There may be one or more usages available. The costs are specified for each. 8. Select a usage.
Opening an application Downloaded applications are stored under the BREW Apps menu. Each application comes with its own unique icon, to help you identify it easily. 1. Select Menu → BREW Apps. Note: The BREW Shop icon will always remain at the top of this menu. Downloaded applications are listed after. 2. Highlight and select the icon for the application you want to open. Viewing application details You can get information about the size of an application and how many uses it has left before it runs out.
Removing an application Important: If you remove an application, it is removed completely from your phone. If you want to use it again, you must pay for it again. If you want to free up space on your phone, we recommend you disable the application (see next page). 1. Select Menu → BREW Apps → BREW Shop → Options. 2. Select the application and then select Remove. 3. Select Yes to confirm your choice.
Checking available memory The amount of available memory depends on the number of applications you downloaded. 1. Select Menu → BREW Apps → BREW Shop → Options. 2. Select Information. The two numbers shown here describe the amount of space used by your existing applications, and the total space allocated for BREW applications. If these two numbers are close in size, you are nearing capacity. Disable or remove some applications.
10 GETTING HELP Customer support Your service provider’s customer support department may be accessible directly from your phone when you dial a number such as *611 (check with your service provider). They can answer questions about your phone, phone bill, call coverage area, and specific features available to you, such as call forwarding or voicemail. For questions about the phone features, refer to the materials provided with your phone, or visit www.kyocera-wireless.com.
• The phone’s electronic serial number (ESN). To find the ESN: a. Remove the battery. b. Locate the white label on the back of the phone. Your phone’s 11digit ESN begins with “D” and is located on the label. Phone accessories To shop for phone accessories, visit www.kyocera-wireless.com/store, or call (800) 349-4188 (U.S.A. only) or (858) 882-1410. Become a product evaluator To participate in the testing and evaluation of Kyocera Wireless Corp. products, including cellular or PCS phones, visit beta.
INDEX Numerics 1-Touch dialing, 24 911 calls, 31 A Alarm Clock, 11, 105 alerts browser, 121 for headsets, 87 for messages, 85 for missed calls, 21 all calls timer, 28 application disabling, 125 downloading, 122 opening, 124 removing, 125 Auto-Answer, 96 Auto-Erase setting, 64 auto-hyphenation, 83 AutoText, 54, 55, 66 B backlighting, 81 banner, 79 battery, 1 drain, 4 removing, 2 safety guidelines, 3 bookmarks, 119 BREW, 121 and available memory, 126 Brick Attack, 111 browser prompt, 121 browser timer, 120 C
delivery receipt for text messages, 55 digital mode, 11 display contrast, 82 Doodler, 113 downloading applications, 122 F Fast Find, 47 fax mode, 89 finding a saved phone number, 46 frequent contacts, 46 FunLights, 77 E emergency 911 calls, 31 making calls after dialing 911, 31 position location, 13, 90 emoticons, 53 erasing all contacts, 85 text messages, 62 external devices hands-free car kit, 18 laptop or PC, 88 TTY/TDD, 88 G games and auto keyguard, 126 Brick Attack, 111 Doodler, 113 downloading, 122
L language, 83 lights backlighting, 81 FunLights, 77 lights-only mode, 13, 70 photosensitivity, 78 power backlighting, 82 limiting calls out, 85 lock code, 83 locking keypad, 27 phone, 84 M memory, 126 saving, 62 menu view, 80 messages see voicemail or text messages minutes counting, 28 missed calls, 21 N net alerts, 120 normal text mode, 34 number mode, 34 number type, 41 O OutBox, 57 P pauses in phone numbers, 42 phone book (Contacts directory), 41 phone numbers editing, 44 finding quickly, 47 saving, 41
alerts, 32 controlling, 32 rejecting calls, 32 ringer, 33 S saved phone numbers editing, 44 finding quickly, 47 searching for, 47 Scheduler, 102 screen contrast, 82 screen icons, 11 screen savers, 79 searching for saved phone numbers, 47 secret contacts, 23, 42 security, 83 shortcuts accessing, 75 creating, 75 silencing all sounds, 70 silent mode 132 icons, 13 setting, 69 sound files attaching to text messages, 115 speakerphone, 20 volume, 74 speed dialing, 24 Stopwatch, 108 symbol mode, 37 T technical sup
U unlocking the phone, 84 V vibrate icon, 13 lights only, 70 setting phone to, 69 silence all, 70 vibrate only, 70 voice dialing digit dialing, 95 expert mode, 94 voice tags adding to contact, 42, 93 editing, 93 voice training, 98 voice wake-up, 96 voice memo erasing, 101 naming, 101 playing, 101 voicemail accessing, 26 setting up, 5, 25 volume earpiece, 27, 73 key beep, 74 ringer, 74 speakerphone, 74 timer, 120 W Web alerts, 120 BREW, 121 downloading applications, 121 security, 118 Web Browser, 117 book
