Contents Contents BEFORE DRIVING ........................................ 1 1. INSTRUCTIONS FOR USE ........................ 1 2. INTRODUCTION .................................... 2 3. GENERAL SAFETY INFORMATION.............. 3 4. GETTING TO KNOW YOUR SCOOTER ....... 14 5. PRODUCT SPECIFICATIONS .................... 17 6. PUSHING AND TRANSPORTING THE SCOOTER ........................................... 18 7. ADJUSTING THE SCOOTER .................... 19 7.1 ADJUSTING THE DISTANCE BETWEEN SEAT AND TILLER ...
Contents 8.8 SWITCHING ON THE HORN ............. 28 8.9 SWITCHING ON THE HAZARD Lights 28 8.10 SWITCHING ON THE TURN SIGNAL 28 8.11 SWITCHING ON THE TEMP ............ 29 8.12 SWITCHING ON THE ADJ .............. 29 8.13 SWITCHING ON THE MOD ............. 29 8.14 SWITCHING ON THE TIME ............ 29 8.15 POWERING OFF/PARKING THE SCOOTER ............................................ 29 8.16 12V POWER SOCKET .................... 30 9. BATTERY AND CHARGING THE BATTERY .. 31 9.1 BATTERY STATUS DISPLAY ...........
INDICATION FOR USE BEFORE DRIVING 1 . I N S T R UC TI O N S F O R U S E The scooter is a motorised electric scooter for use outdoors primarily on flat surfaces such as pavements, roads, parking lots and drive ways. It is intended to increase the mobility of persons who are both physically and mentally capable of correctly assessing driving situations and reacting correspondingly to them at any time. Uses: DO NOT operate this equipment without first reading and understanding the user manual.
INTRODUCTION 2 . I N T R O D UC T I O N DEAR CUSTOMER With your MAXER ForU, you have now purchased a product, which has been manufactured in accordance with the newest technical capabilities and based on the highest operating user comfort. We have placed great value on the simplest possible operation and long service life in both construction and material selection. A large variety of useful accessories rounds off our range in addition to the scooter.
GENERAL SAFETY INFORMATION 3 . G E N E R A L S A F E T Y IN F OR M A T I O N WARNING! Before you operate your scooter, please read and understand all information provided with your scooter for your safety. As operating any vehicle, only drive with full alertness to ensure safety. WARNING! Please observe the warnings below to avoid any damage or injury resulting from improper use of your scooter. The scooter user is responsible for taking proper safety measures.
GENERAL SAFETY INFORMATION WARNING! Anti-tippers substantially reduce your risk of falling over backwards, which can cause serious injury. WARNING! Have someone help you practice bending and reaching on the scooter and transferring to and from the scooter until you learn how to do it safely. WARNING! NEVER try a new maneuver on your own. WARNING! Get to know the areas where you plan to use your scooter. Look for hazards and learn how to avoid them.
GENERAL SAFETY INFORMATION Keep ashtrays a safe distance from the seat cushions. Always make sure cigarettes are completely extinguished before disposal. WARNING! Do not modify your scooter in any way by yourself. For any accessories, please contact your approved service provider for installation by an authorized service technician. WARNING! The addition of accessories to your scooter may change certain specifications such as overall weight, size, and/or center of gravity of your scooter.
GENERAL SAFETY INFORMATION WARNING! Do not place the scooter in “freewheel” mode while the unit is powered up. Always power off the scooter and remove the key from the key switch before engaging or disengaging “freewheel” mode. WARNING! To prevent the scooter from rolling uncontrollably on its own, never place the scooter in “freewheel” mode on any incline or decline. WARNING! If you anticipate being seated in a stationary position for an extended period of time, turn off the power to the scooter.
GENERAL SAFETY INFORMATION electrical system and/or personal injury. Check any actuators for loose, worn, or damaged items and have any damaged wires replaced immediately. WARNING! Check electrical components frequently for signs of corrosion and have them replaced as necessary. WARNING! Always secure the scooter and its batteries when it is being transported. Batteries should be secured in an upright position and protective caps should be secured on the battery terminals.
GENERAL SAFETY INFORMATION WARNING! Always protect the batteries from freezing; for those living in cold climates, make sure you store the scooter properly. Never charge a frozen battery. Charging a frozen battery may result in damage to the battery. WARNING! Do not remove the fuse links from the battery harnesses. If the fuse links appear damaged, contact your authorized provider for service. WARNING! Do not operate the scooter with depleted batteries; you could be stranded.
GENERAL SAFETY INFORMATION WARNING! The maximum recommended incline angles (see specifications) are tested in a controlled environment. Your scooter’s ability to climb up inclines is affected by your weight, speed and the angle you approach the incline among other factors. WARNING! Only drive backwards on a flat surface. When driving backwards, operate your scooter at a lower and even speed. Stop often and check to make sure your path is clear of obstacles.
GENERAL SAFETY INFORMATION WARNING! Do not use the armrests for any weight bearing purposes. Such use may cause the scooter to tip, which may result in a fall from the scooter and personal injury. WARNING! Do not put all of your weight on one side of the scooter deck. Such use may cause the scooter to tip. WARNING! Even though your scooter may be capable of handling greater obstacles, we recommend that you do not attempt to negotiate a curb that has a height greater than 2 in. (5 cm).
GENERAL SAFETY INFORMATION WARNING! Do not expose your scooter to open flames. WARNING! Keep your scooter in a dry and clean condition. Never take your scooter into a shower, tub, pool, or sauna. Rain, snow, salt, mist/spray conditions, and icy/slippery surfaces can damage the scooter components or cause the scooter frame to prematurely rust. WARNING! Avoid prolonged exposure to heat or cold; it may affect the temperature of upholstered and non-upholstered components on the scooter.
GENERAL SAFETY INFORMATION WARNING! It is dangerous to transfer to and from your scooter on your own. It requires good balance and agility. Be aware that there is a point during every transfer when the seat is not below you. WARNING! To make a safe transfer: Always turn off the power before you transfer to or from your scooter. If you fail to do so you may touch the throttle control lever and cause your scooter to move when you do not expect it.
GENERAL SAFETY INFORMATION WARNING! Be aware that washing of upholstered items may reduce the fabric’s resistance to flammability. WARNING! Radio wave sources, such as radio stations, TV stations, amateur radio (HAM) transmitters, two-way radios, and cellular phones ,can affect motorised scooter control. Following the warnings listed below should reduce the chance of unintended brake release or motorised scooter movement, which could result in serious injury.
GETTING TO KNOW YOUR SCOOTER 4 .
GETTING TO KNOW YOUR SCOOTER Head light Service Turn signal switch Speed control dial Temp switch Battery status display ODO/TRIP Speed 44.43 in 20.27 in Time Speed H/L 46.65 in 50 in 18.1 in 6.
GETTING TO KNOW YOUR SCOOTER 58.66 in 84in 84in 24.
PRODUCT SPECIFICATIONS 5. PRODUCT SPECIFICATIONS Model Name EQ40DA(UK) Maximum weight capacity 440 lbs (200kg) Overall height 43.3 in (1100 mm) Overall length 58.7 in (1490 mm) Overall width 24.
PUSHING AND TRANSPORTING THE SCOOTER 6 . P U SH I N G A ND T R AN S PO R T I N G TH E SC OOTER 1. Please carefully read the safety information in section 3 related to transportation first. 2. Pushing the scooter: In order to push the scooter, you must place the scooter in “freewheel” mode, which disengages the drive motor. The lever (1) is located at the bottom right-hand side of the scooter under the seat. WARNING! When the lever is pulled up in freewheel mode: • The scooter must be on a flat surface.
ADJUSTING THE SCOOTER speed is exceeded while you are pushing the scooter, the drive motor will switch on automatically and brake the scooter. After any adjustments, repair or service and before use, make sure all hardware is tightened securely - otherwise injury or damage may result. 7 . AD J U S T I NG T H E SC O O TE R The following describes how to set up and adjust your Scooter in order to have a comfortable and safe drive. 7.1 ADJUSTING THE DISTANCE BETWEEN SEAT AND TILLER 1.
ADJUSTING THE SCOOTER (left or right) to get on. 2. Sit on the seat and turn the seat back to the direction of travel. Lock the seat in place by releasing the seat lever. Fasten your seat belt. Ensure that the seat is properly engaged after adjustment by seeing that the seat doesn’t move when you try rotating it to either side. 7.3 ADJUSTING THE BACKREST ANGLE The backrest angle can be adjusted to three locking stages. 1.
ADJUSTING THE SCOOTER Lowering the headrest: Press the locking lever in and push the headrest down to the desired position. Release the locking lever, and engage the lowering protection by moving the headrest slightly. 7.5 ADJUSTING THE TILLER ANGLE Always adjust the tiller so that you can reach the dashboard and control your scooter easily at any time. 1. Pull the locking lever (1). 2.
ADJUSTING THE SCOOTER engaged in 8 positions (at 45° intervals). Pull the turning lock (1), turn the seat in the required direction or position (2) and engage. Accident hazard due to incorrect seat position: Always turn the seat to face forward and lock it before driving. If the seat has been turned, the possibility of tipping is increased. Before turning the seat, always ensure that the scooter is on an even and solid surface.
OPERATING THE SCOOTER OPERATING 8 . O P E R A TI NG T H E SC O O TE R Always carry out the safety information described in the “General Safety Information” section: Before starting to drive, adjust the seat and tiller to a comfortable position. WARNING! Every scooter is different. Take the time to learn the feel of your scooter before you begin riding. WARNING! BE AWARE that becoming a capable and safe scooter operator will take time and practice.
OPERATING THE SCOOTER Check before you power on Ensure your scooter is in drive mode (not in “freewheel” mode) Seat is locked into the desirable position the scooter: Check the “freewheel” mode lever is in the pushed down position Move the seat forwards and backwards to ensure it is stationary.
OPERATING THE SCOOTER 8.3 ADJUSTING THE SPEED Use the two speed adjustment mechanisms to adjust the speed to suit your driving conditions. Always use lower speed if you are uncertain about the driving conditions. There are two mechanisms to control the speed of your scooter. 1. High/Low Speed Switch: a. It is located on the meter. b. It is designed to preselect the maximum speed levels. c. If the toggle switch is set at “High” level, the maximum speed allowed is 8 mph (12.8 kph) d.
OPERATING THE SCOOTER EQ40DA(UK) 1. High/Low Speed 2. Speed Control Dial: to Toggle: to preselect further adjust the speed level the maximum speed Driving Forwards Turtle Rabbit High Low Driving Backwards High Low 3.5 mph 2.2 mph Turtle 2.4mph 2 mph to to to to 8 mph 3.7 mph Rabbit 2.8 mph 2 mph 8.4 DRIVING FORWARDS AND BACKWARDS Hold the tiller handles firmly with both hands. Use your right index and middle fingers to pull the right side of the lever to move forward.
OPERATING THE SCOOTER 8.5 USING THE BRAKES 1. Using the motor electromagnetic brake: When the throttle control lever is released and returns to the center position, the brake is engaged to stop the scooter. Emergency braking = let go of the drive lever: The throttle control lever automatically returns to the central position if you let go, the scooter automatically brakes. 2. Using the handbrake: To use the handbrake, pull the brake lever (1) slowly towards the handlebar.
OPERATING THE SCOOTER 8.7 SWITCHING ON THE HEADLIGHTS Headlight button : Switch on = press button once Switch off = press button again A switch indicator will light up to show that the headlight is switched on. If you drive with the headlights on, the batteries will drain faster and the scooter driving range will be slightly reduced. 8.8 SWITCHING ON THE HORN Press the horn button. It will sound for as long as you hold the button down. 8.
OPERATING THE SCOOTER 8.11 SWITCHING ON THE TEMP Press the temp button. It will be change the temperature unit of measure. 8.12 SWITCHING ON THE ADJ Press the ADJ button. Hold the ADJ button. 1. set value 2. change speed unit.(km/h or mph) Hold the ADJ and MOD button about 3 seconds. The value returns zero.(in TRIP mode) 8.13 SWITCHING ON THE MOD Press the MOD button. Hold the MOD button about 0.5 seconds to repeat CLOCK-> ODO -> TRIP. 8.14 SWITCHING ON THE TIME Press the TIME button 1.
OPERATING THE SCOOTER - intend to stop for long periods. Always remove the key if you: - want to park the scooter and get off. 8.16 12V POWER SOCKET The power socket provides 12V 2A 24W Voltage-12V. Ampere- 2A. Watt-24W Don’t exceed the applicable power rating when using. If KEY ON over ten minute, 1. The system will go into the sleep mode status. 2. Meter LCD will show a signal. Please reset your key switch (switch off then on).
BATTERY AND CHARGING THE BATTERY 9 . BA T T E R Y A ND CH A R G IN G T H E BATTERY Corrosive chemicals contained in battery. Explosive conditions exist! Do not use batteries with different amphour (Ah) capacities. Keep tools and other metal objects away from battery terminals. Contact with tools can cause electrical shock. Flammable material contained in battery. Do not expose to heat sources such as open flame or sparks. Do not transport batteries with flammable or combustible items.
BATTERY AND CHARGING THE BATTERY 9.1 BATTERY STATUS DISPLAY The battery status display on the dashboard shows the current level of battery power. F = max range E = decreased driving range, charge batteries as soon as possible. If the scooter is at a standstill, it is often the case that the battery status may show full than it actually is. The battery status display may vary greatly while the vehicle is travelling depending on the load.
BATTERY AND CHARGING THE BATTERY 9.2 CHARGING THE BATTERIES It is imperative that you observe the sequence for connecting and disconnecting the battery charger. 1. Position the scooter near an electric outlet. 2. Switch the scooter off and remove the key. 3. Ensure the lever for “freewheel” mode is pushed down to the “drive” position. 4. Connect the battery charger plug into the scooter charging socket located in the centre of the tiller. 5.
BATTERY AND CHARGING THE BATTERY Step 2. Switch the scooter off and remove the key. Step 3. Ensure the lever for “freewheel” mode is pushed down to the “drive” position. Step 4. Connect the battery charger plug (4) into the scooter charging socket located in the centre of the tiller.
BATTERY AND CHARGING THE BATTERY Step 5. Plug the battery charging power cord (1) into the jack socket (2) on the battery charger. Step 6. Connect the battery charger power plug into an electrical outlet (AC115-230V, 50 to 60 Hz) and charge the battery. (Note: There is no switch on the battery charger).
BATTERY AND CHARGING THE BATTERY LED information at battery charger during Charging: LED-> Color-> Meaning 1 --- Green --- battery charger switched on 2 --- Yellow --- charging in progress 3 --- Yellow --- charging 90% 4 --- Green --- charging is complete 9.3 AFTER CHARGING (1.) Remove the battery charger plug from the electric outlet. (2.) Remove the battery charger jack plug from the scooter jack socket. 9.
By KWANG YANG Motor Co., Ltd. Third Edition, NOV. 2013 All rights reserved. Any reproduction or unauthorized use without the written permission of KWANG YANG Motor Co., Ltd. is strictly prohibited. T300-EQ40DA-A1 •NO.35 Wan Hsing Street,San Min District Kaohsiung City, Taiwan, Republic Of China •NO.61,Chung-Shan Sth Rd ,Lu-Chu District ,Kaohsiung City, Taiwan, Republic Of China Date printed:Apr.
KWANG YANG MOTOR CO., LTD No.
