User's Manual

T1
TURE WIRELESS
STEREO EARBUDS
User Manual

Bluetooth : v5.0
Music playme : 4h
Wireless srange : ≥10m
Speaker : 5.6mm,16ohm
Bluooth profiles : HSP,HFP,A2DP,AVRCP
Impedace : 16Ω
Earbuds Baery capacity : 55mAh x 2
Case Baery capacity : 300mAh
Sound pressure level : 98±3dB
Frequency Response : 20Hz-20KHz
Earbuds Weight : 6g x 2


 1-2light on —— 25%-50%
2-3light on —— 50%-75%
3-4light on —— 75%-100%
 Display the baery status aer
connected to Android or IOS devices.

Charging case :charged by Micro-USB cable
Earbuds : charged via charging case
1.The right and le earbud can be used separately
(mono) , also can be used together in pairs
(stereo). Master device is right earbud.
2.This product can connect 2 devices at the same
me.
3.Do not put the device in high temperature
environment or into fire, as not to damage the
baery.
4.There is no removable and maintainable spare
parts,so do not disassemble it.
5.Deal with the waste baeries according to
naonal regulaons.


1. Charging Case
2. Earphones
3. Charging Cable
4. Ear ps
5. User Manual
User
Manual

Press the "Touch Panel" for 3 seconds

Press the "Touch Panel" for 3 seconds

Short Press the "Touch Panel"

Calling state, short press the "Touch Panel"
：
when incoming call, long press the "Touch Panel" for 2
seconds

Music play state,short press the "Touch Panel"

Music play state, double click the "Touch Panel"

Tap the "Touch Panel" for 3 mes
1st ligth on: charging for right earbud
2nd light on: charging for le earbud


Open the charging case,the earbuds will power
on and pairing.Then can be searched in your
device.

Put one of the earbud in the charging case and
remove the other one, it will enter into pairing
mode. Then you can find it in your device and
connect. Or long press "Touch Panel" for
4seconds, unl the blue and red light flashing
alternately. Then enable the bluetooth funcon of
your device, search bluetooth device T1A, and
connect.

Just put the earbuds back into the charging case
and close it , then pick them out again.

Long press “touch panel” of both earbuds for 10
seconds at the same me, unl the blue and red
led flashing alternately.

 FCC FCC
This device complies with part 15 of the FCC rules.
Operaon is subject to the following two
condions (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operaon.
Changes or modificaons not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.This
equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protecon against
harmful interference in a residenal installaon. This
equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instrucons, may cause harmful
interference to radio communicaons. However,
there is no guarantee that interference will not
occur in a parcular installaon.
If this equipment does cause harmful interference
to radio or television recepon, which can be
determined by turning the equipment off and on,
the user is encouraged to try to correct the
interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separaon between the equipment
and receiver.
-- Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV
technician for help.