® OPERATOR’S MANUAL MP7 Official H&K licensed product. Umarex holds the worldwide exclusive HK-Tradmark and exterior design copy license for use with this Umarex product, granted by HK, Inc., U.S.A.
H&K MP7 TABLE OF CONTENTS Use of this Manual............................................................................................2 Safety Guidelines.............................................................................................2 Warranty and Service................................................................................... 4-5 Specifications...................................................................................................6 Contents .............................
USE OF THIS MANUAL Before operating the Airsoft gun, read this manual in its entirety. Important safety topics and tips are discussed throughout all chapters. It is important that the operator know the principals of gun handling safety and operation prior to firing the Airsoft gun. SAFETY GUIDELINES ! WARNING! Failure to follow safety guidelines may result in serious injury. Safety Distance The effective shooting range is approximately 75 feet.
H&K MP7 SAFETY GUIDELINES Identify Your Target and Backstop Before you pull the trigger, make certain of your target and what is beyond it. The Airsoft gun should never be fired at surfaces where BBs are likely to ricochet in unpredictable directions such as rocks, glass, water, or other hard surfaces. ! WARNING! Adult supervision is required for any person under the age of 18. Failure To Fire If the Airsoft gun fails to fire, misfires, or malfunctions, do not look into the barrel.
WARRANTY AND SERVICE KWA Performance Industries, Inc. is committed to serve our customers with the finest quality products, the highest level of service, and customer satisfaction. Because of this, we offer a 45-day warranty on all KWA products we import and distribute. What is Covered Except as specified below, this warranty covers all defects in material and workmanship in KWA products occurring during the above warranty periods.
H&K MP7 NOTE: THE RMA NUMBER MUST BE CLEARLY MARKED ON THE OUTSIDE OF THE PACKAGE. PACKAGES WITHOUT AN RMA NUMBER CLEARLY MARKED WILL BE REFUSED AND RETURNED TO SENDER. NO EXCEPTIONS. This Warranty is Only Valid in the United States If your product does not require service, but you have questions regarding its operation, please contact our Technical Services Department as listed below.
SPECIFICATIONS • Overal Length [Retracted] = 38 cm (14.96”) • Overall Length [Extened] = 60 cm (23.62”) • Overall Height: 26 cm (10.24”) • Inner Barrel Length = 160mm • Inner Barrel Diameter: 6.05 mm • Weight: 2.13 kg (4.7 lbs) • Caliber = 6mm Airsoft BBs • Magazine Capacity = (20) 48 rounds • Gas System = FV • Velocity = 110-116 MPS (360-380 FPS) • Rate of Fire = 20+ RPS* • Energy Output with 0.20g BB: 1.
H&K MP7 CHARGING GAS 1. Release magazine by pressing the magazine catch. 2. Push the gas canister nozzle into the charging valve. Make sure the canister is in a vertical position when charging. 3. Charge magazine until gas overflows from charging valve. ! WARNING: Avoid allowing magazine to drop freely onto hard surfaces; it may damage the magazine.
LOADING BBs 1. Pull magazine follower down until it locks. 2. Insert BBs into magazine lip. 3. BBs should stack staggered for maximum round capacity: 48 rounds. 4. Make sure to have a 3mm clearance between BBs and top lip of magazine. 5. Push magazine follower lock to release. Note: Always use KWA Perfect BBs 0.2 or 0.25G. Using only KWA Perfect BBs can give your air sports gun its best performance. Using improper and low grade BBs may damage the gun.
H&K MP7 LOADING MAGAZINE 1. Place magazine back into magazine well. 2. Push up magazine until it clicks into locked position. 3. Pull magazine down to assure that it has been locked in place. Magazine SELECTOR Selector is located behind the trigger. Select icon with one bullet shape to fire semiautomatic (single shot) and select icon with multiple bullets to fire full automatic (continuous shots). Semi-Auto Full-Auto SAFETY Safety is located behind the trigger.
FRONT SIGHT ADJUSTMENT Higher Lower ! WARNING! If turned too far, the front sight will come off. REAR SIGHT ADJUSTMENT Rear Sight More Left Windage Knob More Right HAND GRIP To use hand grip, pull hand grip downward untill it locks. To put away hand grip, push down on grip lock button then push hand grip upward toward gun.
H&K MP7 RETRACTABLE STOCK 1. Push stock button upward. 2. Pull retractable stock outward until it lock into place. 1 2 Stock Button COCKING Before firing, the bolt must be in full cock position. To put bolt in full cock position, pull the cocking lever toward the rear of the gun. NOTE: For absolute assurance against accidental discharge due to inadvertent trigger pull, keep the manual safety engaged during loading or unloading. WARNING: Always keep finger off the trigger until ready to fire.
HOP–UP SYSTEM The Hop Up device is one of the KWA standard features. Hop gives Airsoft BBs greater stability, further travel and increased accuracy. Being light-weight, Airsoft BBs can be affected by wind when fired. With the Hop up system, the trajectory of the Airsoft BBs can be adjusted according to the surroundings (or environment) you are in.
H&K MP7 Cleaning procedure The Airsoft gun barrel should be cleaned and lubricated after each shooting session. Regular cleaning prevents the effects of BB residue buildup, and ensures all parts are lubricated properly. 1. Ensure that the safety is engaged 2. Disable Hop-Up by dialing to the normal position 3. Remove the magazine and clear the chamber of loaded BBs 4. Disassemble the receiver (see Disassembly section) 5. Steps to use cleaning rod: a.
SYMPTOMS BASIC TROUBLESHOOTING GUIDE POSSIBLE CAUSE SOLUTIONS Slide jams / Will not complete cycle Dry internal Add silicone to cylinder / main seal/ rails Double feeds BB’s into chamber / BB’s roll out of barrel Hop-up adjustment too tight Release hop-up or replace bucking BB’s will not release from magazine / bent mag lip/ check bb condition Bended magazine lip Leaking release valve & charging valve Dry O-ring Add silicone oil to valves Safety lever not working Loose screw on lever Tighten
H&K MP7 PARTS DIAGRAM 15
16
H&K MP7 PARTS DIAGRAM 17
PARTS LIST Parts # Description Parts # Description Parts # Description 199-0111-1 Frame 199-0111-37 Main Seal Base Screw 199-0111-71 Hammer 199-0111-2 Front Grip Bushing 199-0111-72 Hammer Spring 199-0111-3 Front Receiver Cover 199-0111-73 Hammer Spring Retainer Pin 199-0111-4 Flash Hider Bolt Catch Release Lever “Left” Bolt Catch Release Lever “Right” 199-0111-74 Hammer Pin 199-0111-5 Outer Barrel 199-0111-40 Release Lever Allen Screw 199-0111-75 Hammer Pin 199-0111-6 Outer
H&K MP7 PARTS LIST Parts # Description Parts # Description Parts # Stock Butt Pad Allen Screw 199-0111-120 x2 199-0111-107 Stock Butt Pad Base 199-0111-108 Butt Pad Allen Screw 199-0111-121 Bolt Buffer Pad Base 199-0111-109 Butt Pad Base Plunger 199-0111-122 Bolt Buffer Pad Butt Pad Base Plunger 199-0111-110 Spring Description 199-0111-133 Sight Blade Plunger Spring 199-0111-134 Sight Blade Plunger Cover 199-0111-135 Sight Blade Plunger Screw Sight Windage Knob Ball Bearing 199-0111-123 Front
MMD11_MP7 V01 R2011.06.08 KWA Performance Industries, Inc. 18571 E. Gale Ave City of Industry, CA 91748 T: 626.581.1777 • F: 626.581.0777 www.kwausa.com Copyright © May, 2011 KWA Performance Industries, Inc. All Rights Reserved.
