® OPERATOR’S MANUAL G36C Official H&K licensed product. Umarex holds the worldwide exclusive HK-Tradmark and exterior design copy license for use with this Umarex product, granted by HK, Inc., U.S.A.
H&K G36C TABLE OF CONTENTS Use of this manual............................................................................................2 Safety Guidelines......................................................................................... 2-3 Warranty and Service................................................................................... 4-5 Specifications...................................................................................................6 Contents .............................
USE OF THIS MANUAL Before operating the Airsoft gun, read this manual in its entirety. Important safety topics and tips are discussed throughout all of the chapters. It’s important that the operator know the principles of gun handling safety and operation prior to firing the Airsoft gun. SAFETY GUIDELINES ! WARNING! Failure to follow safety guidelines may result in serious injury. Safety Distance The effective shooting range is approximately 175 feet.
H&K G36C SAFETY GUIDELINES Identify Your Target and Backstop Before you pull the trigger, make certain of your target and what is beyond it. The Airsoft gun should never be fired at surfaces such as rocks, glass, water, or other hard surfaces where BBs are likely to ricochet in unpredictable directions. ! WARNING! Adult supervision is required for any person under the age of 18. Failure To Fire If the Airsoft gun fails to fire, misfires, or malfunctions, do not look into the gun barrel.
WARRANTY AND SERVICE KWA Performance Industries, Inc. is committed to serve our customers with the finest quality products, the highest level of service, and customer satisfaction. Because of this, we offer a 45-day warranty on all KWA products we import and distribute. What is Covered Except as specified below, this warranty covers all defects in material and workmanship in KWA products occurring during the above warranty periods.
H&K G36C This Warranty is Only Valid in the United States If your product does not require service, but you have questions regarding its operation, please contact our Technical Services Department as listed below. THIS WARRANTY IS EXPRESSLY MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
SPECIFICATIONS • Overall Length [Fixed] = 50.5 cm (19.88”) • Outter Barrel Length = 72 mm (28.35”) • Inner Barrel Length = 247 mm • Inner Barrel Diameter = 6.05 mm • Weight = 2.62 kg (5.77 lbs) • Barrel thread = -14 mm • Caliber = 6 mm • Magazine Capacity = 400 rounds • Rate of Fire = 20+ RPS • Velocity = 116~122 MPS (380~400 FPS) • Energy Output with 0.20g BB = 1.5 Joules • Power Source = 9.6v NiMh, 7.4v or 11.
H&K G36C LOADING HIGH CAP Magazine 1. Release the magazine by pressing the magazine release button. 2. Open the magazine trap door and pour the Airsoft BBs into the chamber. Close the door when the chamber is full. 3. Turn the winding wheel on the bottom of the magazine to tighten the spring tension. This will allow the Airsoft BBs to feed through the top of the magazine. 4. Insert the magazine into the Airsoft gun until it clicks into place. NOTE: Spring tension will unwind as you fire the gun.
FIRE SELECTOR SWITCH 1. Safe In Safe mode the gun will not fire. For safety reasons, you should keep the switch in Safe mode at all times when you are not ready to fire. 2. Semi-Auto In Semi-Auto mode the gun will fire one shot each time you pull the trigger. 3. Full Auto In this Full Auto mode the gun will fire continuously as long as the trigger is depressed. ! WARNING: Do not pull the trigger when switching the fire selector.
H&K G36C BATTERY INSTALLATION 1. Set the fire selector switch to safe mode then remove hand guard retaining pin. 2. Slide hand guard off. 3. Turn gun over and place battery into compartment, back end first, then plug battery into connector. 4. Place hand guard back on the gun. Align retaining pin holes and push the retaining pin back into the gun. Make sure to push the retaining pin all the way in until click securily into place.
HOP–UP SYSTEM The Hop-Up device is one of KWA’s standard features, giving Airsoft BBs greater stability, further travel and increased accuracy. Airsoft BBs are light-weight and can be affected by wind when fired. With the Hop-Up system, the trajectory of the Airsoft BBs can be adjusted according to the shooting environment or surroundings. HOP-UP ADJUSTMENT • Fold and then pull the charging handle to the rear, the ejection port will open and Hop-Up adjustment dial is revealed.
H&K G36C SIGHT ADJUSTMENT Adjust the sight vertically by turning elevation adjusting screw using 2.5mm hexagonal key for the elevation screw. Turning adjusting screw clockwise and counterclockwise to lower and raise the rear sight respectively Adjust the sight horizontally by turning wintage adjusting screw using 2.5mm hexagonal key for the elevation screw. Turning adjusting screw clockwise and counterclockwise to shift the rear sight to right and left respectively.
Cleaning and Lubrication ! WARNING! Unload and clear the Airsoft gun of all BBs before cleaning. Cleaning Procedure The Airsoft gun barrel should be cleaned and lubricated after each shooting session. Regular cleaning prevents the effects of BB residue buildup, and ensures all parts are lubricated properly. 1. Ensure that the safety is engaged 2. Disable Hop-Up by dialing to the normal position 3. Remove the magazine and clear the chamber of loaded BBs 4.
H&K G36C BASIC TROUBLESHOOTING GUIDE FOR RIFLE SYMPTOMS CAUSE SOLUTIONS Selector set to Safe Mode Select Semi-Auto or Full-Auto Mode Dead battery Replace or Charge battery Burned out fuse Replace with a new fuse Motor damaged or bad connection Return gun for professional care Pinched wiring Return gun for professional care Motor is running but not firing Internal failure Return gun for professional care Motor or Battery is hot after short use Pinched wiring Return gun for professional car
Operating Under Unusual Conditions Unusual conditions are defined as any condition requiring special maintenance. Perform maintenance outlined for the climate similar to your operational area Extreme Cold: Operating an Airsoft gas gun in extremely cold temperatures is not recommended. Cold temperature will cause the Hop-Up Bucking to harden, reducing its effectiveness or cause the gearbox shell to fracture during operation, rendering the gun inoperable.
H&K G36C PARTS DIAGRAM 71 167 168 70 181 33 167 118 26 165 39 210 165 117 209 104 34 153 36 202 38 103 21 203 152 162 123 119 163 37 195 66 67 35 127 163 22 190 128 162 196 190 23 196 190 195 170 130 195 M6 M3 M124 M32 M13 M123 M33 M37 129 M7 M42 M117 M114 M10 M11 M119 M38 M19 M29 M28 M27 M1 M36 M46 M43 M21 M18 M24 M44 M5 M45 M12 M20 M107 M120 M101 M125 M125 M125 M125 M2 15 M125 M35 M23 M47 13 M116 M40 M127 M39 M125 M97 M30 2 M4
121 156 72 125 74 68 96 197 194 24 184 157 80 199 187 170 76 122 73 81 94 30 188 120 25 188 188 80 124 188 31 69 167 167 189 42 167 167 78 131 187 81 155 166 126 80 81 187 154 75 198 188 32 126 166 40 95 189 166 159 158 77 151 53 5 52 43 54 51 150 181 174 2 116 148 16 132 149 M39 181 48 1 208 55 169 49 56 178 178 175 89 14 182 16
H&K G36C PARTS LIST Parts # 199-1001-1 199-1001-2 199-1001-5 199-1001-14 199-1001-16 199-1001-21 199-1001-22 199-1001-23 199-1001-24 199-1001-25 199-1001-26 199-1001-30 199-1001-31 199-1001-32 199-1001-33 199-1001-34 199-1001-35 199-1001-36 199-1001-37 199-1001-38 199-1001-39 199-1001-40 199-1001-42 199-1001-43 199-1001-48 199-1001-49 199-1001-51 199-1001-52 199-1001-53 199-1001-54 199-1001-55 199-1001-56 199-1001-66 199-1001-67 199-1001-68 199-1001-69 199-1001-70 199-1001-71 199-1001-72 199-1001-73 199-10
Parts # Description 199-1001-M36 199-1001-M37 199-1001-M38 199-1001-M39 199-1001-M40 199-1001-M42 199-1001-M43 199-1001-M44 199-1001-M45 199-1001-M46 Parts # TRIGGER SWITCH CONTACT PISTON HEAD PISTON HEAD GUIDE SPRING GUIDE END CAP SPRING GUIDE TAPPET PLATE SPRING TRIGGER SWITCH RETURN SPRING TRIGGER SPRING CUT OFF LEVER SPRING SAFETY BLOCK SPRING 199-1001-M47 199-1001-M48 199-1001-M97 199-1001-M101 199-1001-M107 199-1001-M113 199-1001-M114 199-1001-M115 199-1001-M116 199-1001-M117 Description Parts
MMD15_G36C V01 R2011.08.22 KWA Performance Industries, Inc. 18571 E. Gale Ave City of Industry, CA 91748 T: 626.581.1777 • F: 626.581.0777 www.kwausa.com Copyright © May, 2011 KWA Performance Industries, Inc. All Rights Reserved.
