User Manual
Table Of Contents
- 1.1 Intended Use
- 2.1 Unpacking and checking the contents
- 1. Introduction
- 2.1 Unpacking and checking the content
- 1.5 About the status LED
- 1.4 Product elements
- 1.3 Technical specifications
- 1.2 Safety intructions
- 3. Using on screen menu
- 2.8 Best practice for Windows 10
- 2.7 Removing a fiber cable
- 2.6 Replacing the SFP module
- 2.5 Start up
- 2.4 media4Kconnect in the Matrix Vario System
- 2.3 Installing the extender
- 2.2 Mounting kit
- 4.1 Menu Features
- 3.4 Settings
- 3.3 Update menu
- 3.2. Features menu
- 3.1. System status
- 5.2. Disposal
- 5.1 Extender Care
- 4.1.2 Matrix Switching System
- 6. Support & First Aid
- 8.1 Switches
- 9.1 extended warranty
- 10. Address & phone / emails
- 11. Notes
18 | kvm-tec kvm-tec | 19
Misprints, errors and technical changes reserved Misprints, errors and technical changes reserved
2. EXTENDER INSTALLATION 2. EXTENDER INSTALLATION
2.5 START UP
To start up the system:
1. Make sure that monitor and computer are switched on.
2. If you are using a Network Switch, connect the power cable to an earthed wall socket.
3. Connect both extender power cables ( 6 / 20 ) to an earthed wall socket. Switch on both
units. Both extenders start an initialization process. The status LED blinks some seconds
red and changes to green after a successful connection The monitor will displays your
computer’s desktop or any open applications.
2.6 REPLACING THE SFP MODULE
The Media4K is delivered with a multimode SFP + module.
To replace an SFP module with a different SFP+ module:
1. Remove the black dust protector from the SFP+ module.
2. Pull the metal latch of the SFP+ module forwards until it is at a right angle.
3. Replace the SFP+ module with the other module. Put the metal latch back in position. Only
use SFP+ modules from kvm-tec, or recommended by kvm-tec.
2.4 MEDIA4KCONNECT IN THE MATRIX VARIO SYSTEM
4K
Full
HD
MATRIX
VARIO
SYSTEM
2
Get the
DUAL View
Simultaneous Downscaling from 4K to Full HD
In the Matrix vario system, the
media4K local unit is the star
Because in the Matrix Vario system, a single
local media4Kconnect unit is everybody‘s
darling on the remote wishlist and two dif-
ferent resolutions can be displayed and edi-
ted simultaneously.
4K sources can be displayed simultaneous-
ly in 4K and with downscaling in Full HD on
the remote unit. The output of the stream
is done at 4K over 10G bandwidth. Two
streams are transmitted simultaneously, so
the 4K stream has 9 GBIT and the second
stream in Full HD 1 Gbit.
The streams can be routed and shared inde-
pendently and one source can be split to any
number of screens. One user has full USB
control (keyboard and mouse etc).
Full
HD
4K
Full
HD
media4Kconnect remote
Flexline remote
Laptop mit gateway2GO
media4Kconnect
local
Who is for new KVMs? 4K or Full HD ?
Many solutions have the disadvantage that a decision
between 4K and Full HD has to be made during the plan-
ning phase. The Matrix vario system allows 4K to be used
where it is needed, making the solution more affordable
and exible to use.
www.kvm-tec.com
Who is Who in the Matrix Vario System
Local Unit/TX/CPU: media4Kconnect – DP1.2 Extender in Fiber
Remote Unit/RX/CON: media4Kconnect for 4K resolution
Flexline KVM Extender over IP Extender for Full HD resolution
Gateway2go APP – for alle Remote – Home Oce applications or in
LAN the KVM solution without remote extender