User Manual

Program Mode
Editing VAST Programs
6-13
TwoofthesoftbuttonsintheProgramEditorarespecialcases.They’rethesoftbuttonsthat
selecttheeditingpagesforthefirstandlastDSPfunctions(PitchandLevel,respectively)ofthe
currentprogram’salgorithm.OneofthesesoftbuttonsislabeledPITCH,andpressingitwill
take
youtotheDSPCTL(DSPControl)pagewiththePitchparameterhighlighted.Theother
oneofthesesoftbuttonsislabeledAMP,andpressingitwilltakeyoutotheDSPCTLpagewith
theLevelparameterhighlighted.Additionally,pressingtheDSPCTLsoftbuttonwilltakeyou
totheDSPCTLpage.
The MODE Buttons in the Program Editor
WhenintheProgra meditor,eachoftheMODEselectbuttonhasadifferentfunction.Beside
eachbuttonisthenameofitsfunctionintheProgrameditor.Whenactivated,thebutton’sLED
willlightup.
Mute 1, 2, 3, and 4
EachofthetopfourMODEselectbuttonsservetomuteoneofthecurrent
program’sfirstfour
layers.PressingtheProgrambuttonmuteslayer1,pressingtheMIDIbuttonmutes layer2,
pressingtheSetupbuttonmuteslayer3,andpressingtheMasterbuttonmuteslayer4.
Solo
PressingtheQAccessbuttonsolosthecurrentlayer.
Mute Active
PressingtheSongbuttonmutesthecurrentlayer.
FX Bypass
PressingtheEffectbuttonbypassesalleffects.Note,however,thatifeitheroftheAuxOverrides
inEffectsmodeareactive,thenthoseeffectsarestillapplied.
Compare
PressingtheStoragebuttoncallsuptheCompareEditor,whichrecallstheprogrampre‐edit
settings,allowingyoutocompareyoureditedprogramwith
theoriginalprogram.Pressingthe
StoragebuttonagainreturnsyoutotheProgrameditor. UsingtheCompareEditormakesno
changestothecurrentprogram.
Assigning Program Parameters to Control Sources
ManyPC3KprogramparameterscanbeassignedtobecontrolledbythePC3K’sphysical
controllersorbyMIDICCsfromanexternalMIDIdevice.Fordetailsoncontrollableparameters
ofVASTprograms,seethefollowingsections:TheDSPModulation(DSPMOD)
Page on page 6‐30,TheLFOPage on page 6‐38,TheASRPage on page 6‐
40,TheFunction(FUN)
Page on page 6‐41,TheEnvelopeControl(ENVCTL)Page on page 6‐45,TheMOD
Pages on page 9‐10,andFXLFO,FXASR,andFXFUNpages on page 9‐11.ForKB3programs,see
thefollowingsectionsKB3Editor:ThePITCHPage on page 6‐62,KB3Editor:TheAMP
Page on page 6‐62,KB3Editor:TheLFO,ASR,and
FUNPages on page 6‐70,TheMOD
Pages on page 9‐10,andFXLFO,FXASR,andFXFUNpages on page 9‐11.
Foreachprogram,theProgramEditorcanbeusedtoassignthePC3K’sphysicalcontrollersor
externalMIDIcontrollerCCnumberstocontrolparameters.Controllableparameterseachhave
asourcefield.Makeassignmentstothesource
fieldforthedesiredparameter.Sourcefieldsare
nameddifferentlydependingontheirpage:Src1,Src2,RateCt,Trigger,Input a,Inputb,and
Source.ToassignaPC3Kphysicalcontroller,selectthesourcefieldfortheparameter,holdthe
Enterbuttonandmovethecontroller.ToassignaCCnumber
toasourcefield,enterthenumber
withthealphanumericpad,thenpressEnter.ACCnumberforanexternalcontrollercanalsobe
setbyselectingthesourcefieldfortheparameter,holdingtheEnterbutton,andsendingaCC
valuefromtheexternalMIDIcontroller.Whenassigninga
CCnumbertoasourcefield,the
numbermaybedisplayedinthesourcefieldasthenameofthatCC’sdefaultuse.