User Manual

Program Mode
Control Setup
6-11
Table 6-4 Control Setup Parameters Affecting Program Mode
About PC3K Physical Controller Destinations
PC3Kphysicalcontrollerstransmitcontrollermessagesconsistingofadestinationandavalue.
Thedestinationallowsthephysicalcontrollertobeidentified,whilethevaluerepresentsthe
currentstateofthephysicalcontroller(buttonon/off,slidersetting,etc.)Eachdestinationcanbe 
identifiedasanumber(thoughsomedestinationsare
displayedinthePC3Kasthenameoftheirdefault
use.)DestinationscanbeMIDIcontinuouscontrollernumbers(0‐127)orPC3Kinternal
destinations(128andabove.)Forsimplicity,wewillrefertobothofthesetypesofdestinations
asCCnumbers,orCCs(continuouscontrollernumbers.)
Bydefault,physical
controllerdestinations0‐127aretransmittedinternallytoprogram
parameters,andtotheUSBandMIDIOutportsasMIDIcontinuouscontrollernumbers(see
Destination on page 10‐2tochangethisbehavior.)
Physicalcontrollerdestinations128andaboveareonlytransmittedinternallytoprogram
parameters.Destinationsabove127cannotbeassigned
asaprogramparametercontrolsource.
Somedestinationsabove127willstillaffectProgramModeeventhoughtheycannotbe
assignedasaprogramparametercontrolsource.Forexample,destination133Tempoalways
controlsthesystemtempo.Inthecontrolsetup,settingaslidertodestination133Tempowould
make
thatslideralwayscontrolsystemtempowhileinProgrammode.Thismightbeusefulto
changethetempowhenusingthearpeggiatorinProgrammode,thoughthesliderwouldn’ tbe
abletocontrolanythingelseinProgrammode.SeeTheControllerDestinationList on page 7‐21
fordetailsoneachcontrollerdestination.
About Program Parameter Sources
Inprogrammode,whenyouwanttocontrolaparameterwithaphysicalcontroller,yousetthe
parameterssourcefieldtothedestination thatthephysicalcontrollerissendingto.Forexample,
bydefaultthedestinationfortheModWheelisCC1.Ifyouselectasourcefieldinthe
Program
Editor,thenpress1followedbytheEnter button,thatparameterwillbecontrolledbytheMod
Wheel.Inthiscase,theparametercouldalsobecontrolledbyCC1 being sentfromanexternal
MIDIdevice.
Youcanassignadestinationtoasourcefieldbyselectingthesource
field,holdingtheEnter
button,thenmovingthephysicalcontrollerthatyouwanttouse.FormostofthePC3K’s
physicalcontrollers,theirdestina tion nameinthesourcefieldisdisplayedwiththenameofthe
controlleronthePC3K’sfrontpanel.
Control Setup–Setup Editor Page (Zone 1) Parameters Affecting Program Mode
CH/PROG Arpeggiator, Destination, BankMode
KEY-VEL All
PAN-VOL ExitVolume, ExitPan
BEND AuxBend1Up, AuxBend1Dwn, AuxBend2Rng
COMMON Tempo, ArpSync
ARPEGGIATOR All
RIBBON CONFIGUR All
Continuous Controller assignment pages (SLIDER,
SLID2, CONT.PEDALS, RIBBON, WHEEL, PRESS)
Dest, Scale, Add, Curv
Switch Controller assignment pages (FOOT
SWITCH 1-3, SWITCH ARP, SWITCH SW, PRG
SWITCH 1-8)
Type, OnControl, OnValue, OffControl,
OffValue, EntryState