User Manual

Setup Mode
Controllers
7-31
Switch Type (Type)
Theparametersforswitchcontrollersareslightlydifferentfromthoseforcontinuous
controllers.ThefirstparameterisType.ThechoicesavailableareMomentaryinwhicha
switch’sactionlastsonlyaslongasyouarepushingit,andToggle,inwhichtheswitch’saction
lastsuntilyoupressitagain.
Momentarymodeisusedforfunctionslikesustainorportamento,whileTogglemodeisused
forfunctionssuchasarpegg iatoron/off.Thebuttonsshowwhichmodetheyareinbythe
behavioroftheirlights:ifabuttonisinMomentarymode,itslightglowsonlyaslongasyouare

holdingit,whileifitisinTogglemode,thelightstaysonuntilyoupressitagain.Bearinmind
thatbuttonassignmentsareindependentperzone,andsincethere’sjustasinglelightper
button,thelightshowsthestateofthebuttononlyforthecurrentzone.
Whenyoupressthe
button,however,itexecutesitsassignmentsforallzonesthatusethatbutton.
On Control (OnControl)
OnControldetermineswhatMIDIControllerorothermessagewillbesentwhentheswitchis
on—thatis,eitherpressedandheldortoggledfromtheoff position.Thelistofavailable
controllersonpage 7
‐21isthesameasforthecontinuouscontrollers,andcanbeaccessedthe
sameway.
Off Control (OffControl)
OffControldetermineswhatMIDIControllerorothermessagewillbesentwhentheswitchis
off—thatis,eitherunpressedortoggledfromtheonposition.Thelistofavailablecontrollerson
page 7‐21is
thesameasforthecontinuouscontrollers,andcanbeaccessedthesameway.
OnValue
OnValuesetsthevalueoftheControllerwhentheswitchison.Inthecaseofconventionally
switchedfunctions,suchassustain,theOnValuewillbe127.(Forexample,thedefaultfor
Footswitch1isController
64—Sustain—withanOnValueof127.)However,youmightwant
touseabuttonorpedalasa“soft”switch,inwhichcaseyoumightsetOnControlto7(Volume)
andOnValueto50,andOffControlto7andOffValueto127.OnControlandOffControl
canalso
bothbesettoOff,sothatturning ontheswitchhasnoeffectatallinthiszone.Thiscanbe
usefulwhenyouareusingoneswitchformultiplefunctionsindifferentzones.
OffValue
OffValueisthevalueoftheControllerwhentheswitchisoff.The
defaultvalueis0.Youmight
wanttochangethis,asinthe“softswitch”exampleabove:inordertobringthezoneuptofull
volumewhenyoureleasethepedal,setOffValueto127.
Entry (Ent) and Exit States
EntryStatedetermineswhetheraninitialsettingfortheswitchwillbesentwhen
thesetupis
selected.Therearethreechoices:None(nochange),Off(theOffvalue),andOn(theOnvalue).
WithaPanelSwitchbutton,iftheEnt ry StateisOn,thebuttonwilllightassoonasyouselect
thesetup.
ExitStatesimilarlydetermineswhetherasettingfor
theswitchwillbesentwhenyouleavethe
setup,eitherforanothersetuporforProgrammode.Thesamethreechoices(On,Off,and
None)areavailable.Thisisveryusefulforturningoffsustainswhenchangingsetups.