User Manual

7-30
Setup Mode
Controllers
Entry (Ent) and Exit Values
EntryvalueallowsyoutospecifyaninitialvalueforacontrollerinaSetupthatwillbesent
wheneveryouselectthatSetup.Forexample,ifyouwanttomakesurethatallofthe
modulationforthePrograminaZoneisturnedoffwhenyouselecta
Setup,usetheSetup
EditortoassignaphysicalcontrollertoadestinationofMIDI01(MWheel)andsetEntryValue
to0.(TheModWheelisusuallyassignedtodestinationMIDI01MWheel,whichisusedto
controlamodulationparameterformostPrograms.)
Entryvaluesignorethecurrentposition
ofthephysicalcontrollerwhenthesetupisselected.By
default,oncetheSetupisloadedandtheentryvalueshavebeensent,movingacontrollerwill
instantlysendnewcontrollervalues.Thiscancauseajumpinvaluesifthecontrollerhappens to
besettoavaluefar
fromitsentryvalue.Toavoidthesejumps,changetheSetupCtlsparameter
inMasterModetoPassEntry(seeSetupControllers(SetupCtls) on page 11‐2fordetails.)With
SetupCtlssettoPassEntry, movingthecontrollerwillhavenoeffectuntilitmovespastitsentry
value.Inthiscase,continuingthemodulationexample
above,movingtheassigned controller
won’tturnonanymodulationuntilit’spushedallthewaydown(passingentryvalue0,)and
thenupagain.
AnentryvalueofNoneisquitedifferentfromavalueof0.Nonemeansthattherewillbeno
initialcontrollercommandwhenthesetup
isselected,andanysubsequentmovementofthe
physicalcontrollerwillbeeffective.
ExitValuetellsthePC3Ktosendavalueforthatcontrollerwheneveryouleavethesetup,either
byselectinganothersetuporbyselectingadifferentmodealtogether.Itcanbeveryusefulwhen
acontrolleris
doingsomethingtothe sound,andyoudon’twantthateffecttocontinueafteryou
leavethesetup.Forexample,ifyouwanttomakesureazone’spitchreturnstonormal
wheneveryouleaveasetup,youwouldsetExitValueto64foranycontrollerwhoseDestination
parameter
issettoPitchUp.Again,Nonemeansnocommandissent.
Note:Programscanalsobesavedwithcontrollerentryvalues(ontheProgramEditor
CONTROLLERSpage.)WhenaSetupisloaded,entryvaluesfor theProgramsintheSetupare
sentfirst,followedbytheentryvaluesfortheSetup.
Becauseofthis,ifaSetupandaProgram
usedbyaSetuphaveentryvaluessetforthesamecontroller,theentryvalueforthe Setupwill
beused.IfaProgramusedbyaSetuphasanentryvaluesetforacontroller,buttheSetuphasan
entryvalueofNone forthesamecontroller,theentryvaluefromtheProgramisused.
Switch Controller Parameters
Switch(physical)controllershaveonlytwostates:onandoff.ThePC3Kswitchcontrollersare:
•PanelSwitchesArpandSW
• FootswitchPedals1,2,and 3
• ProgrammableSwitches1–8(ProgramSelectbuttons1–8)
KeepinmindthefollowingtwothingswhenworkingwiththePC3K’sswitches.First,inSetup
ModetheBank
buttonsabovetheslidersarededicatedtozonestatusandmuting,andarenot
assignablecontrollers.(IfthesetupcontainsaKB3Program,theBankbuttonscanbeusedtocontrol
KB3functions,seeMutes on page 7‐66for details.)Second,inProgrammode,theProgramSelect
buttonsfunctionasprogramselect
buttonsifnoneofthemareassignedtoadestinationinthe 
controlsetup(seeControlSetup on page 6‐9fordetails.)IfatleastoneProgrammableSwitchis
assignedinthecontrolsetup,thentheassignedProgramSelectbuttonsactasassigned,but
noneofthebuttonsfunctionasprogramselect
buttons.