Product Manual

ManualsBrandsKunz Engineering ManualsFloatation KitAcrEase Mower

ASSEMBLY INSTRUCTIONS

Kunz Engineering Inc. Mendota, IL

Rear Floatation Kit 003907

Front Floatation Kit 003908

Cross Brace Tube Assy. 900113

1/09

READ THE COMPLETE ASSEMBLY INSTRUCTIONS BEFORE

STARTING THE ASSEMBLY.

- one caster support as at attached

- two cross brace tube assemblies

lift kit or a 44” model:

gh cut models only)

1. or models

ith the electric lift kit installed or any 44” rough cut models, refer to section E. For models

ccording to figure 1. The measurement

should be taken from the front edge of the carrier arm and extend to the center of each hole.

ause difficulty during assembly.

u should have the following parts with the complete floatation kit:

- one rear wheel support assembly with receiver assemby and clamping flat attached

sembly with receiver assembly and clamping fl

You should have the following parts if you currently have an electric

- one rear wheel support assembly with receiver assemby and clamping flat attached

- one caster support assembly with receiver assembly and clamping flat attached

- four 1/2” thick spacer flats (44” rou

WARNING: Before doing any installations or adjustments shut off mower engine.

A. CARRIER ARM PREPARATION (Refer to Figure 1)

For models that already have mounting holes present, section A. can be omitted. F

without mounting holes, locate the hole positioning a

The front hole should be at a distance of 10-3/4” from the front edge of the carrier arm and the

rear hole should be 65-9/16” from the front edge of the carrier arm. Hole positioning will nee

to be located on both the left and right carrier arms.

2. Using a 17/32” (.531”) drill bit, drill all four holes. Take care to drill straight through the carrier

arms.

Note: Hole misalignment from top to bottom may c

Summary of content (5 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS Kunz Engineering Inc. Rear Floatation Kit 003907 Front Floatation Kit 003908 Cross Brace Tube Assy. 900113 Mendota, IL 1/09 READ THE COMPLETE ASSEMBLY INSTRUCTIONS BEFORE STARTING THE ASSEMBLY.
PAGE 2
Front 10-3/4” Carrier Arm 65-9/16” Figure 1. Carrier Arm Hole Location Receiver Assy. Caster Support Assy. Cross Brace Tube Wire Lock Pin Rear Wheel Support Assy. Clamping Flat Figure 2.
PAGE 3
B. INSTALL CROSS BRACE TUBES (Refer to Figure 2) 1. Remove the 1/2” x 5-1/2” bolts and lock nuts from the ends of both of the cross brace tubes and save for step 2. 2. Align the cross brace tubes over the holes that were drilled in section A. For models that already have mounting holes present, use the two holes that are closest to the center of the carrier arm. Place the 1/2” x 5-1/2” bolts through the carrier arm from the bottom up. Place the lock nut on the bolt from the top side.
PAGE 4
. Position the receiver assemblies in the desired location on the upper actuator mount. Insert the four 1/2” x 3-1/2” bolts from the bottom up and place the clamping flat on the top. Secure the bolts with the lock washer and the nut. Tighten down appropriately to prevent unwanted loosening. Note: If the floatation kit is positioned to the same side as the tongue there may be interference. It may be necessary to relocate the tongue and hitch pivot to the opposite side. 5.
PAGE 5
6 4 8 9 4 5 8 5 3 2 1 1 7 PARTS LIST Item 1 2 3 4 5 6 7 8 9 Part # 216011 226003 226004 600195 900107 900108 243010 900109 900110 900148 222012 600272 Description Wire Lock Pin (1/2" x 3-1/2" Opening) Offset Wheel Assy. (15/60 x 6, 4 Ply Turf) Centered Wheel Assy. (5.30/4.50 x 6, 4 Ply Stud) Clamping Flat Reciever Assy. Caster Support Plastic Bearing (1-3/8" O.D. x 1.00" I.D., Flange, Nylon) Rear Wheel Support Cross Brace Tube Caster Fork Single Split Collar (1" I.D. x .