Product Manual

ManualsBrandsKunz Engineering ManualsLiftAcrEase Rough Cut Mower Wetlands Kit

Table Of Contents

A. INSTALL REAR TIRE EXTENSION (Refer to figure 1)
- PARTS LIST

ASSEMBLY INSTRUCTIONS

Kunz Engineering Inc. Mendota, IL

Wetlands Kit

003905

1/09

READ THE COMPLETE ASSEMBLY INSTRUCTIONS BEFORE

STARTING THE ASSEMBLY.

You should have the following parts with the wetlands kit:

n with hardware - one rear tire extensio

ill not

- two caster assemblies

- two 15/600 x 6 tires with hardware

CAUTION: The rough cut mower w float with the wetlands kit installed. Do not go into

A. IN

l. Remove the right rear tire assembly

water deeper than 2-3”.

WARNING: Before doing any installations or adjustments shut off mower engine.

STALL REAR TIRE EXTENSION (Refer to figure 1)

1. Block the mower deck up to allow for easy tire remova

and save the tire for step 2.

2. Insert the rear tire extension into the lower rear opening of the right carrier arm. Align the hole

on the rear tire extension with the hole on the carrier arm. Place a 5/8” x 7.5” bolt through the

aligned holes in the correct orientation shown in figure 1. Place a 5/8” x 7.5” bolt in the other

available rear tire extension hole using the correct orientation shown in figure 1.

3. Install both tires in the following order and fasten securely. (cup washer, washer, tire, washer

& lock nut)

Summary of content (4 pages)

PAGE 1
ASSEMBLY INSTRUCTIONS Kunz Engineering Inc. Wetlands Kit 003905 Mendota, IL 1/09 READ THE COMPLETE ASSEMBLY INSTRUCTIONS BEFORE STARTING THE ASSEMBLY. You should have the following parts with the wetlands kit: - one rear tire extension with hardware - two caster assemblies - two 15/600 x 6 tires with hardware CAUTION: The rough cut mower will not float with the wetlands kit installed. Do not go into water deeper than 2-3”. WARNING: Before doing any installations or adjustments shut off mower engine. A.
PAGE 2
Carrier Arm Rear Tire Extension Figure 1. Right Rear Tire Extension B. INSTALL FRONT CASTERS (Refer to figure 2) 1. Remove the single split collar that holds the front caster assemblies in place and remove the caster assemblies. On older models there may be a cotter pin that needs to be removed at the top of the caster assembly. Single Split Collar Carrier Arm Caster Assy. Caster Assy. Figure 2.
PAGE 3
2. Install a new caster assembly on both sides of the mower in place of the old caster assemblies. Place the thick washer on the bottom of the carrier arm and the thin washer on the top. Install the single split collar on each caster assembly and fasten securely. C. INSTALL LEFT REAR TIRES (Refer to figure 3) 1. Remove the left rear tire assembly and save the tire for step 2. 2. For this step, use the 5/8” x 12” bolt provided. Install both tires in the following order and fasten securely.
PAGE 4
8 6 9 4 11 2 5 9 7 7 5 5 5 3 3 5 9 7 1 5 5 1 10 7 9 5 3 PARTS LIST Item 1 2 3 4 5 6 7 8 9 10 11 Part # 202140 202142 212015 214014 214018 214019 214021 222012 226003 900091 900149 Description Hex Head Bolt 5/8" x 7.5" Hex Head Bolt 5/8" x 12.0" Centered Lock Nut 5/8" Machinery Washer 1" I.D. x 1.5" O.D. x 18 GA Machinery Washer 5/8" I.D. x 1" O.D. Machinery Washer 1" I.D. x 1.5" O.D. x 10GA Cup Washer Single Split Collar 1" I.D. x 1/2" Thick Offset Wheel Assy.