DF PROFI II PCI Installation Instructions V1.6 27.02.2017 Project No.: Doc-ID.
h:\dokumente\project\5302_df_profi_ii\anwenderdoku\installation\pci\kunbus\version_1.6\df profi ii pci_e.doc Revision History Version Date V1.6 V1.5 V1.4 V1.3 V1.1 V1.0 30.07.2013 30.07.2013 23.09.2009 04.08.2009 08.01.2008 13.08.
DF PROFI II PCI - Installation Instructions Contents Contents 1 Installation of the Board ................................................................................................ 1 2 Safety Instructions ........................................................................................................ 2 3 Pin Assignment ............................................................................................................. 3 4 Description of the LEDs .............................
Contents DF PROFI II PCI - Installation Instructions List of Figures Figure 1: DF PROFI II PCI Board ........................................................................................... 1 Figure 2: PROFIBUS Terminator ........................................................................................... 3 Figure 3: Declaration of Conformity, page 1 ........................................................................... 6 Figure 4: Declaration of Conformity, page 2 .........................
DF PROFI II PCI - Installation Instructions 1 Installation of the Board Installation of the Board The DF PROFI II PCI is a plug & play compatible board for 5 V and 3.3 V 32-Bit PCI-Slots. The configuration entirely takes place by means of the delivered software or the BIOS of your PC respectively. Thus, no jumpers or DIP switch adjustments are necessary.
Safety Instructions 2 DF PROFI II PCI - Installation Instructions Safety Instructions WARNING: Disregarding this warning may result in damage to equipment and/or serious personal injury. Only qualified personnel may start up and operate this device. According to the safety instructions in this text, qualified personnel are persons who are authorized to start up, to ground, and to mark devices, systems, and equipment according to the standards of safety technology.
DF PROFI II PCI - Installation Instructions 3 Pin Assignment Pin Assignment Pin Number 1 3 5 6 8 Signal RxD/TxD-P 0V (potential free 80 mA) 5V (potential free 80 mA) RxD/TxD-N Function shielding Data+ Feeding of bus terminator Feeding of bus terminator Data- Direction Input/Output Input Output Input/Output Table 1: Pin Assignment Remark: To assure correct operation of the PROFIBUS, a terminating resistor must be mounted at each bus end (Purchase No.: 4000-7-002-H).
Description of the LEDs 4 DF PROFI II PCI - Installation Instructions Description of the LEDs Green LED: On: Firmware loaded and started Off: Firmware not loaded Yellow LED: On: PROFIBUS started Off: PROFIBUS stopped Red LED: On: PROFIBUS failure (min. one slave not connected to the bus or with external diagnosis) Off: No PROFIBUS failure 4 V1.6 / 27.02.
DF PROFI II PCI - Installation Instructions 5 Technical Data Technical Data Processor Net+Arm 40, 33 MHz PROFIBUS Controller ASPC2, 48 MHz Memory 1 Mbyte SRAM 2 Mbyte Flash Type Memory PCI Interface 32 Bit (supports both 5 V and 3.3 V) PROFIBUS Interface 1 * Sub-D 9 pins Interface Physics RS485 (isolated) PROFIBUS Data Rates 9600 Bit/s - 12000 KBit/s Data Size of Process Image max.
Declaration of Conformity 6 DF PROFI II PCI - Installation Instructions Declaration of Conformity Figure 3: Declaration of Conformity, page 1 6 V1.6 / 27.02.
DF PROFI II PCI - Installation Instructions Declaration of Conformity Figure 4: Declaration of Conformity, page 2 KUNBUS V1.6 / 27.02.
Declaration of Conformity DF PROFI II PCI - Installation Instructions Figure 5: Declaration of Conformity, page 3 8 V1.6 / 27.02.
DF PROFI II PCI - Installation Instructions Declaration of Conformity Final Page ! KUNBUS V1.6 / 27.02.
