Kunak AIR Pro QUICK START GUIDE Rev: 6 Reproduction in whole or in part is expressly prohibited without the written consent of KUNAK TECHNOLOGIES S.L. www.kunakair.
Kunak AIR Pro – QUICK START GUIDE v.6 SUMMARY 1. QUICK START GUIDE ............................................................................................................................................ 2 1.1 Package Content ............................................................................................................................................ 2 1.2 Required Tools and Equipment..........................................................................................................
Kunak AIR Pro – QUICK START GUIDE v.6 1. QUICK START GUIDE 1.1 Package Content The Kunak AIR Pro is always supplied mounted into the solar shield and with an eSIM preconfigured to work with it. To install and configure a SIM card, please refer to the manual on how to change the SIM card. Gas cartridges, probes and power supplies are sent separately.
Kunak AIR Pro – QUICK START GUIDE v.6 1.3 Parts of a Kunak AIR Pro Station Figure 1 – Parts of a Kunak AIR Pro 1. 2. 3. 4. 5. 6. Inlet Particle sensor Support holder Outlet Particle sensor Metallic grid Solar Shield External Temp, Humidity, pressure and dew point sensors 7. Cartridge 8. Power button 9. Connectors for power and optional probes 10. LCD display 11. Display Buttons 12. LEDs indicators 1.
Kunak AIR Pro – QUICK START GUIDE v.6 1.5 LEDs Indicators and Display Buttons The LEDs below the display indicate the current status of the device. GREEN INFORMATION LED ON ON Powering ON or OFF ON OFF Error status OFF ON Measuring or connecting to the Kunak Cloud ON (blink 1Hz) OFF Device ON at stand-by mode and charging OFF OFF Between measures or powered off There are two buttons below the LCD that will change the LCD messages.
Kunak AIR Pro – QUICK START GUIDE v.6 The probes or extra sensors can be plugged to the Kunak AIR Pro device in every moment and some of them depends on the characteristics chosen at the purchase time. The probes will be automatically detected at start-up of the device. The features of each connector are: • • Connector 1 (M12 x 4 pins type T): Power 7V to 12V. Connector 2 (M12 x 4 pins type D): o K-A3-xx-3: Ethernet PoE. o K-A3-xx-4: Modbus Slave. • Connector 3 (M12 x 5 pins type B): Sound Level Meter.
Kunak AIR Pro – QUICK START GUIDE v.6 1 Remove the metallic grid cartridge protector by loosening the bolts and sliding the protector forward. Plug the cartridges of your choice into the device. ➢ Be careful when inserting the cartridges into the device, the pins can bend if the cartridge is not inserted perpendicularly. ➢ The device connections.
Kunak AIR Pro – QUICK START GUIDE v.6 Install the device far away from very close pollution sources and without enough air flow (chimneys, air conditioners, etc), that may disturb your readings. If a sonometer is also going to be placed, install it in a place with low wind impact, avoiding vibration sources and avoiding electromagnetic sources. Install the unit between 3 and 4 meters high. If the unit is installed with solar panel, locate the devices far away from buildings, trees, etc….
Kunak AIR Pro – QUICK START GUIDE v.6 1 Place the base of the support on a wall or mast. 2 Place the support to the base with the two bolts. 3 Place the device inside the support through the groove. 4 Screw the two captive fixing bolts. Connect the power connector and the probes. Screw the probes connectors all the way in. 5 ➢ 6 The device must be switched off during connections. Power ON the device returning from “stand-by” by pressing the sleep button or by pressing down the power ON button.
Kunak AIR Pro – QUICK START GUIDE v.6 1.11 Storage and Transportation There are some aspects to consider if the Kunak AIR Pro device is going to be stored or transported to change of location. Before uninstalling the device, turn it off. 1. Push the sleep button for 5 seconds. 2. LCD will show that is sending the last data. 3. Wait until the LCD and the LEDs are off. To avoid the stabilization period of the gases sensors, let the device at Stand-by mode.
Kunak AIR Pro – QUICK START GUIDE v.6 Figure 6 – Last connection time in Kunak Cloud The device must turn green or yellow (with warnings) indicating that is connected and checking the “last connection time”. It can be read when the last connection was made. Once the device has successfully connected to the cloud, it sends one measurement to Kunak Cloud before start working at the configured sampling and sending periods. These values can be checked in the dashboard.
Kunak AIR Pro – QUICK START GUIDE v.6 Sampling period 5 mins 10 seg Sending period 30 mins 30 mins Guard period 2 mins 5 mins Table 2 – Examples of Guard period regarding the Sampling and Sending period Therefore, if it is desired to have a very small sampling period of e.g. 1 minute, it is recommended that the sending period is large, at least 1 hour, to minimise the number of data that are lost due to the guard period. 1.
