Datasheet

58 www.kuebler.com © Fritz Kübler GmbH, subject to errors and changes. 10/2016
Pulse counters, electronic
Display LCD, 7 digits, 8 mm [0.32“] high
Counting range 0 ... 9999999,
no decimal point
Data backup EEPROM
Operating temperature -20°C ... +65°C [-4°F ... +149°F]
(non-condensing)
Storage temperature -25°C ... +75°C [-13°F ... +167°F]
Power supply 10 … 30 V DC, max. 25 mA
Start delay 500 ms
EMC standards EN 55011 class B,
EN 61000-6-2, EN 61000-6-3,
EN 61326-1
Counting input A fast input,
PNP switching (max. 8 kHz)
Counting input B slow input,
NPN switching
(mechanical contact, max. 48 Hz)
Reset key enable input static NPN input
Reset edge-triggered NPN input
(min. 20 ms)
Input resistance 10 kOhm
Switching level LOW 0 … 2 V DC
HIGH 3.5 … 30 V DC
Switching threshold approx. 2.7 V DC
Scaling 1 … 4095 (factory-set)
General technical data
Technical data
Inputs
Electrical characteristics
Mechanical characteristics
Additional data for Codix 142 (service counter)
Housing front panel mount DIN 43700,
48 x 24 mm [1.89 x 0.94“]
dark grey Ral 7021
Weight 40 g [1.41 oz]
Protection IP65 (front side)
IP20 (rear side)
Connections 8-pole screw terminals,
pitch 5.08 mm [2.00“]
Vibration resistance acc. to EN 60068-2-6 10 ... 55 Hz / 1 mm [0.04“] / 30 min
Shock resistance
acc. to EN 60068-2-27 100 G: 2 ms
10 G: 6 ms
Output NPN transistor output,
open collector
Output voltage max. 30 V DC
Output current max. 50 mA
Accessories Dimensions in mm [inch] Order no.
Transparent cover, lockable, IP65
Sealing cover type K1, IP65
for cut-out 54 x 29 [2.13 x 1.14], for screw mounting to front bezel F1B or
adapter front bezel N003001,
for counters with cut-out 50 x 25 [1.97 x 0.98] or 45 x 22.2 [1.77 x 0.87]
N003002
suitable for front bezel 60 x 50 [2.36 x 1.97], for screw mounting of electromech.
counters and via adapter front bezel N003001 for counters 48 x 24 [1.89 x 0.94] G008301
Suitable gaskets, other accessories and installation examples for optional accessories can be found in chapter accessories or in the accessories section under: www.kuebler.com/accessories.
Adapter front bezel, 72 x 36 [2.83 x 1.42]
Adapter front bezel, 53 x 28 [2.09 x 1.10]
Adapter front bezel, 56 x 40 [2.20 x 1.57]
Adapter front bezel, 48 x 48 [1.89 x 1.89]
Adapter front bezel, 60 x 50 [2.36 x 1.97]
for cut-out 68 x 33 [2.68 x 1.30] to cut-out 45 x 22.2 [1.77 x 0.87],
for counters 48 x 24 [1.89 x 0.94], as set black and silver anodised 162704 Set
for cut-out 50 x 25 [1.97 x 0.98] to cut-out 45 x 22.2 [1.77 x 0.87],
with clip mounting for counters 48 x 24 [1.89 x 0.94] anthracite T008180
for cut-out 50 x 25 [1.97 x 0.98] to cut-out 45 x 22.2 [1.77 x 0.87],
with screw mounting for counters 48 x 24 [1.89 x 0.94] anthracite T008181
for cut-out 45 x 45 [1.77 x 1.77] to cut-out 45 x 22.2 [1.77 x 0.87],
with clip mounting for counters 48 x 24 [1.89 x 0.94] black T008883
for cut-out 54 x 29 [2.13 x 1.14] to cut-out 45 x 22.2 [1.77 x 0.87],
with screw mounting and gasket for counters 48 x 24 [1.89 x 0.94] black N003001
Mounting frame
with cut-out 50 x 25 [2.36 x 1.97]
via separate adapter also for 45 x 22.2 [1.77 x 0.87]
for snap-on mounting on 35 [1.38] top-hat DIN rail,
for counters 53 x 28 [2.09 x 1.10]
and via separate adapter (T008180) for counters 48 x 24 [1.89 x 0.94] chromated G300004
LCD pulse counters Codix 140 / 142Adding counter / service counter (DC)