Owner's manual

ManualsBrandsKT&C ManualsCamcordersKPC-HDX210M

HD CCTV

Digital Video Camera

OPERATION MANUAL

Thank you for choosing our high quality camera.

Before attempting to connect or operate, please read and follow

these instructions.

M133-HDX210-001

Summary of content (32 pages)

PAGE 1
M133-HDX210-001 HD CCTV Digital Video Camera O PE R AT ION MANUAL T h a n k y o u f o r cho o si ng o u r hi gh q uality cam er a. Be f o re a t t e m p t i ng to co n n e ct o r op er ate, please r ead and follow th e se i n s t r u c t i on s.
PAGE 2
CA UTION These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
PAGE 3
CONTENTS 1. CAUTIONS 2. IMPORTANT SAFETY INSTRUCTION 3. FEATURES 4. EQUIPMENT AND ACCESSORIES 5. CAMERA COMPONENT DESCRIPTIONS 6. INSTALLATION 7. DIMENSIONS 8. SPECIFICATION 9.
PAGE 4
1. CAUTIONS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
PAGE 5
1. CAUTIONS Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicate that it should not be disposed with other household wastes at the end of its working life.
PAGE 6
2. IMPORTANT SAFETY INSTRUCTION 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
PAGE 7
3. FEATURES • High Resolution. 1/3” SONY Progressive Color CMOS Image Sensor, 1920 x 1080 60fps • Support various digital video output. 720p30, 720p60, 720p25, 720p50, 1080i60, 1080i50, 1080p30, 1080p25 • Video Output. Primary HD-SDI (BNC) Test / Setup TV Out (BNC), NTSC / PAL selectable. • Support RS485 Communucation Protocol for Camera Configuration Remote Control. • OSD menu for setup and configuration. • Lens Control. Manual Iris, DC Iris (or Video Iris : factory selectable).
PAGE 8
4. EQUIPMENT AND ACCESSORIES HD C C T V Di g i t a l Vi d e o C ame ra AU T O I R I S L EN S CO N N E C T I O N P L U G C-M O U N T A D A P T O R R IN G O PE R A T I O N MA N U A L TER M I N A L B L OC K HDcctv 1.
PAGE 9
5.
PAGE 10
5. CAMERA COMPONENT DESCRIPTIONS • BACK ① ② ⑤ ⑦ HDcctv 1.0 OUTPUT ④ ③ ⑥ AC 24V DC 12V ⑧ ⑪ ⑩ ⑨ ①. MENU SET BUTTON MENU NAVIGATION BUTTONS ②. UP BUTTON ③. DOWN BUTTON ④. LEFT BUTTON ⑤. RIGHT BUTTON ⑥. POWER LED ⑦. SDI OUT BNC ⑧. VIDEO OUT BNC ⑨. MIC IN JACK ⑩. AUDIO OUT JACK (TBD) ⑪.
PAGE 11
6. INSTALLATION • LENS CONNECTION Mega Pixel Lenses are sold separately. Lenses such as an auto iris lens, CS-Mount lens and C-Mount lens can be used (adapter included for C-Mount Lens). NOTE • Please keep the lens clean. • Any foreign objects and Finger marks on the lens can cause inferior image quality in low light level conditions. When using an auto iris lens 1. Please peel off about 8mm of the outer skin of the auto iris lens cable. 2.
PAGE 12
6. INSTALLATION 3. Please remove the cover of the auto iris lens connection plug and solder the lens cable to the connector pin in the plug. * PIN ASSIGNMENT OF THE LENS CONNECTOR 1) Video auto iris lens Pin 1: Power source(DC 12V) Pin 2: N.C(Not used) Pin 3: Video signal Pin 4: Shield, GND(Ground) 2) DC auto iris lens Pin 1: DAMP-(CTL-) Pin 2: DAMP+(CLT+) Pin 3: DRV+ Pin 4: DRV-(GND) 4.
PAGE 13
6. INSTALLATION 5. Please insert the connection plug from the auto iris lens cable into the auto lens connector, which is located on the side of the camera. *NOTE When using a CS-Mount Lens, you can attach it directly to camera. If using a C-Mount Lens, you must attach the ring spacer provided, otherwise if will crack the image sensor.
PAGE 14
6.
PAGE 15
6. INSTALLATION • MONITOR CONNECTION HDcctv DVR or Other HDcctv Signal Equipment To HD - SDI IN HDcctv 1.
PAGE 16
7. DIMENSIONS Unit(mm) MOUNTING HOLE (1/4"-20 UNC, Depth 5) 143.5(C-Mount) 72.5 66 138.
PAGE 17
8. SPECIFICATION Image Device Effective Pixels Unit cell size Video output mode SONY 1/3” Progressive Color CMOS Image Sensor 2096(H) x 1561(V) 60fps 2.5um(H) x 2.5um(V) HD-SDI : 720p30, 720p60, 720p25, 720p50, 1080i60, 1080i50, 1080p30, 1080p25 TV Out : NTSC / PAL selectable Minimum illumination 1.0 Lux S/N Ratio Shutter speed Max 50dB Auto / Manual selectable Min.
PAGE 18
9.
PAGE 19
9. OSD MANUAL - LENS Menu LENS LENS TYPE DC IRIS (VIDEO IRIS) / MANUAL IRIS IRIS VOLUME 0 ~ 50 - EXPOSURE Menuv EXPOSURE SHUTTER SHUTTER MODE NORMAL AE NORMAL AE / AE HOLD / MANUAL AE PRIORITY GAIN NORMAL / GAIN / SHUTTER GAIN LEVEL 0 DB / 1.2 DB / 3.31 DB 5.12 DB / 6.92 DB / 9.33 DB / 11.14 DB / 12.94 DB / 15.34 DB / 17.16 DB / 18.96 DB / 21.37 DB / 23.18 DB / 24 DB / 27.09 DB / 29.
PAGE 20
9.
PAGE 21
9. OSD MANUAL - IMAGE Menu IMAGE GAMMA Y GAMMA PRESET 0 ~ PRESET 3 C GAMMA PRESET 0 ~ PRESET 3 SHARPNESS 0 ~31 CONTRAST 0 ~ 31 SATURATION 0 ~ 31 DNR OFF / LOW / MIDDLE / HIGH PRIVACY ZONE SELECT ZONE 0 ~ ZONE 14 MASK ON / OFF ON / OFF TRANSPARANT 0 / 0.5 / 0.
PAGE 22
9. OSD MANUAL - SYSTEM Menu SYSTEM FIRMWARE VER COMMUNICATION CAMERA ID NO. 0 ~ NO.255 BAUD RATE 2.4K / 4.8K / 9.6K 19.2K / 38.4K /57.
PAGE 23
9. OSD MANUAL • Main Menu MAIN MENU ＋ VIDEO ＋ LENS ＋ EXPOSURE ＋ WHITE BALANCE ＋ DAY / NIGHT ＋ IMAGE ＋ SYSTEM ＊ EXIT - VIDEO : Select SDI out format and TV out format. - LENS : Select the IRIS type and adjust the IRIS control value. - EXPOSURE : Adjust exposure control. - WHITE BALANCE : Adjust white balance control. - DAY / NIGHT : Day & Night control. - IMAGE : Apply image processing effects. - SYSTEM : System information & setting. - EXIT : Close OSD Menu.
PAGE 24
9. OSD MANUAL • Video VIDEO OUT ＊ SDI RESOLUTION ＊ SDI FRAME RATE ＊ CVBS FORMAT 1080p 30HZ NTSC - SDI RESOLUTION Use the LEFT/RIGHT button to select the SDI output video resolution - 720p, 1080i, 1080p * Note : When the OSD menu is not displayed on video, 720p resolution can be selected by pressing the UP button in 5 seconds. Similarly, 1080p resolution can be selected by pressisng the DOWN button in 5 seconds.
PAGE 25
9. OSD MANUAL • EXPOSURE EXPOSURE ＋＊＊＊＊＊ SHUTTER FLICKERLESS BRIGHRNESS AGC BLC WDR OFF 30 140 OFF OFF ＊ ESC ＊ EXIT - SHUTTER Use the SET button to go to the SHUTTER sub menu. - FLICKERLESS Use the LEFT/RIGHT button to select the flickerless control setting - OFF, 60Hz, 50Hz. - BRIGHTNESS Use the LEFT/RIGHT button to adjust the brightness reference level.
PAGE 26
9.
PAGE 27
9.
PAGE 28
9. OSD MANUAL • Day / Night DAY & NIGHT DAY & NIGHT ＊ DAY & NIGHT AUTO ＊ DELAY TIME 3 SEC ＊ DAY THRESHOLD ＊ NIGHT THRESHOLD ＊ DAY & NIGHT EXT 101 188 ＊ ESC ＊ EXIT ＊ ESC ＊ EXIT DAY & NIGHT ＊ DAY & NIGHT DAY & NIGHT COLOR ＊ ESC ＊ EXIT ＊ DAY & NIGHT BW ＊ ESC ＊ EXIT - DAY & NIGHT: Use the LEFT/RIGHT button to select Day & Night modes - AUTO, EXT, COLOR, BW AUTO Auto controlled by AGC level in the processor. (AGC Type) EXT Auto controlled by EXT signal. COLOR Fixed Day State. Color Image.
PAGE 29
9. OSD MANUAL • IMAGE IMAGE ＋＊＊＊＊＋＊ GAMMA SHARPNESS CONTRAST SATURATION DNR PRIVACY MIRROR 7 17 18 OFF OFF ＊ ESC ＊ EXIT - GAMMA: - SHARPNESS: - CONTRAST: - SATURATION: - DNR: - PRIVACY: - MIRROR: Use the SET button to go to the GAMMA sub menu. Use the LEFT/RIGHT button to adjust the sharpness value. Use the LEFT/RIGHT button to adjust the contrast value. Use the LEFT/RIGHT button to adjust the saturation level. Use the LEFT/RIGHT button to select the digital noise reduction level.
PAGE 30
9. OSD MANUAL • PRIVACY MASK (Sub Menu) PRIVACY MASK ＊＊＊＊ ZONE SELECT MASK ON / OFF TRANSPARANT COLOR ZONE 0 OFF 0.5 WHITE ＋ POSITION CONTROL ＊ ESC ＊ EXIT - ZONE SELECT: Use the LEFT/RIGHT button to select the mask zone number to setting. Use the LEFT/RIGHT button to select ON/OFF the mask that is zone selected. - TRANSPARENT: Use the LEFT/RIGHT button to adjust the mask transparent level. - COLOR: Use the LEFT/RIGHT button to select the mask color.
PAGE 31
9. OSD MANUAL • SYSTEM - FIRMWARE VER : SYSTEM ＊＊＊＊＊ FIRMWARE COMMUNICATION AUDIO OUTPUT FOCUS MODE FACTORY RESET 0.2B.25 DISABLE OFF - AUDIO OUTPUT: ＊ ESC ＊ EXIT - FOCUS MODE: - FACTORY RESET: - COMMUNICATION: Information of camera’s firmware version. Use the SET button to go to the COMMUNICATION sub menu. Use the LEFT/RIGHT button to select the audio output ENABLE/ DISABLE. Use the LEFT/RIGHT button to select ON/OFF the Focus mode.
PAGE 32
Quick Setup Guide(HD CCTV CAMERA) ■ OSD Menu Button. UP / 720p LEFT / NTSC RIGHT / PAL DOWN / 1080p - Video out Format Change (NTSC/PAL Selection) Default(Factory default setting) video out format is NTSC. Camera power on & Until push the SET button(While OSD menu is not displayed on video), Can select NTSC/PAL video format output on VIDEO port - Push the LEFT button to select NTSC format video out mode or Push the RIGHT button to select PAL format video out mode.