K9 SERIES USER’S MANUAL 960H DVR K9-a400 K9-a900 K9-a1600 K9-a400 For safe use of system and to prevent product failure or accident, please read this manual carefully before use.
K9-a Series Manual Before Usage This product has been designed and manufactured to assure personal safety. Improper use can result in electronic shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing. This product does not contain any parts that can be repaired by user. [Note] Some contents of this manual are subject to change for function improvement.
K9-a Series Manual Note of Caution Warning Check if the power is switched off before Check if the power is switched off before installation. Don‟t plug in at the same time. installation or additional repair. Never plug in Otherwise it may be set on fire or put you at while the device is in operation. Otherwise it the risk of electrocution or damage. might be set on fire or put you at the risk of fire, electrocution and damage.
K9-a Series Manual When strange noise or smell is sensed, Do not install device in humid place filled with immediately plug out and send inquiry to dust. It might be the cause of electrocution and service center or seller. fire. Caution Do not install the device in any place where Do not put anything heavy on the product. strong magnetic flow, electric wavelength and Otherwise it may be the cause of disorder. vibration may be sensed or where radio, TV or other wireless device is located.
K9-a Series Manual When HDD saving data gets old enough, video When any abnormal sign is detected, data to be saved may suffer so much damage Immediately contact seller or service center. that it may be irreparable. If screen appears broken while regenerating data saved in HDD, it means HDD won‟t work any longer. Immediately contact service center to replace them.
K9-a Series Manual Check Components Battery DVR Screw Software USB Mouse Adaptor Power Cable Component DVR Controller Description Stand Alone Digital Video Recorder Battery 1.5V (AAA) 2 PCS.
K9-a Series Manual - Contents – Chapter 1. Features & Components 1-1 Features……………………………………………………………………………………………..……………………………………….9 1-2 Name and function of front panel……………………………………………………..……………………………………….10 1-3 Rear panel…..…………………………………………………………………………..…………………………………….11 1-4 Remote Controller……………………………………………………………………………..……………………………………….12 Chapter 2. Basic Information 2-1 Menu Display…………………………………………………………..…………………………………………..…………….…….16 2-2 Description of Icon…………………………………………………………………………………………………………..….
K9-a Series Manual 5-3 Email Notification…………..……………………………………………………………………………………….………………….36 5-4 Web Server…..…………………..……………………………………………………………………………………….………………….36 5-5 Free DDNS...…………………..…………………………………….………………………………………………….………………….37 5-6 Dual Codec Setup……………..…………………………………………………………………………………….………………….37 Chapter 6. Camera 6-1 Camera Setting……………...…………………………………………………………………………………………..…………..…38 6-2 Camera Title……………...…………………………………………………………………………………………..…………..…38 6-3 PTZ Setting………………………………………………………...
K9-a Series Manual ▒ Chapter 1. Features & components ▒ 1-1. Features The highly advanced and high-performance video recorder is designed to make it easier to install and use with safety. Main feature ㆍAble to control the PTZ by using mouse like joystick ㆍFront USB port for easy backup ㆍAble to back up by ODD (optional) ㆍSupport GIGA bit Ethernet. ㆍAble to access internet with dynamic IP address ㆍSupport Dual-Stream network transmission.
K9-a Series Manual 1-2. Name and Function of Front Panel (Front Panel Image) No 1 Button/Function Direction Button / Playback Button Description Use as a control button on Setup menu Speed control on playback, Stop button, Pause button.
K9-a Series Manual 1-3. Rear Panel This unit requires no special tools for DVR installation process.
K9-a Series Manual (16Ch rear panel) [1] VIDEO INPUT [2] VIDEO LOOP OUT [3] RJ-45 [4] USB (REAR) [5] RS-485 [6] ALARM OUT [10] AUDIO OUT [11] E-SATA INPUT [12] VGA OUT [14] SPOT OUT [15] POWER INPUT [16] POWER SWITCH [7] SENSOR INPUT [8] SERIAL PORT [9] AUDIO INPUT [13] COMPOSITE MONITOR OUT [17] HDMI 1-4.
K9-a Series Manual 【Video Input】 Use BNC connector to connect coaxial video source. 【Loop through Video out】 【VGA Out】 It is for VGA connection monitor use.
K9-a Series Manual 【RS-485 connection (PTZ camera)】 PTZ camera Please refer to above diagram for PTZ connection. 【RS-485 connection (External keyboard connection)】 Please refer to the keyboard manual for setup. 【Alarm Out connection】 It supports 1 alarm out. Please refer to above diagram for proper setup.
K9-a Series Manual 【Sensor Input connection】 The DVR supports 4 sensor inputs. Please refer to above diagram for proper setup. 【RJ-45 Port(Internet connection)】 The DVR can be connected to the network through 10/100/1000Mbps ethernet connection for remote viewing capability. 【USB Port】 There are 2 USB ports each on front and back. These ports can be used for firmware upgrade, backup and mouse connection.
K9-a Series Manual It is for HDMI connection monitor use. 【E-SATA】 It is for the external HDD connection. It needs E-SATA cable for connection. ▒ Chapter 2. Basic Information ▒ 2-1. Menu Display It‟s available to call setup menu with menu button on front panel, a mouse or the remote controller. ☞ Display Setup Menu with a front panel button „Menu‟ button on the front of unit ☞ Display Setup Menu with a remote Press Menu button on a remote.
K9-a Series Manual Recording Motion Detection Sensor [2] Camera title will be shown as above.
K9-a Series Manual [3] Status Bar 1. Display date and time 2. ER means Emergency Recording and SR means Schedule Recording. 3. Show network status and key lock status. 4. Show HDD status and display “Overwrite” when overwrite function is enabled. 2-3. Remote Controller It is available to use all functions on the DVR with a remote. Controlling several DVRs with one remote is also available.
K9-a Series Manual [1] ID : Press to select a remote controller ID in case of using one remote to control multiple DVRs. [2] SPLIT : Press to display various split modes. Keep pressing the same button will toggle different modes. [3] BACK UP : Press to start archiving stored data to external media. [4] AUDIO : Select an audio channel. [5] SEQ : Press to display each camera in sequence. [6] PTZ : Bring up PTZ control menu. [7] SEARCH : Press search button to playback recorded data.
K9-a Series Manual [9] SET UP : Press to display setup menu. [10] DIRECTION KEY / CONFIRM BUTTON / PLAYBACK CONTROL [11] Record Button – toggle between Emergency Recording and Schedule Recording • EMERGENCY : Emergency Recording Button • SCHEDULE : Schedule Recording Button 2-4. How to set remote controller ID In order to use remote controller, the ID must be the same on both DVR and remote controller. By assigning DVR ID differently, the user can control multiple DVRs with one remote controller.
K9-a Series Manual Remote controller ID menu displays as above image when you press ID button of remote controller. • DVR ID : It displays current ID of the system. • “0” : Input the same ID number of DVR and press “Confirm” 2-5. How to display menu It is available to display menu with front panel buttons, remote and mouse. [1] Front panel button : Push “MENU” button on the front panel.
K9-a Series Manual 2-6. Zoom in/Out Magnify the image at live or playback. [1] How to magnify with a mouse Move the mouse pointer to the position you want to magnify. And hold down left button and drag it to select an area. You can cancel the selection by making another selection within the selection. [2] How to magnify with a remote (Front panel button) • On Live : Display Menu and select “Zoom In/ Zoom Out”. And move with direction buttons.
K9-a Series Manual [1] Remote ID : Assign the ID of remote controller so that user can control multiple DVRs with one controller. (ID range : 0 ~ 99) [2] Language : Select a language [3] Version : Show Software, Hardware and Network version information [4] Health : Indicates storage status. • Hard Disk 1~2 : Display the temperature of hard disk • E-SATA : Display the temperature of hard disk connected to E-SATA • Board : Display the temperature of the DVR‟s main board.
K9-a Series Manual [1] Time : Set time [2] Date : Set date [3] Date format : Select a Time/Date display format. [4] Daylight Saving Time : Set “ON” to apply daylight saving time. Enter Month/Week/Day to begin and also enter Month/Week/Day to end. [5] Time Server : Set time automatically through internet.
K9-a Series Manual • Time server : Input the URL of server (Default : us.pool.ntp.org) • Synchronize Period : Select the period to syncronize between DVR and time server • Power On : Try to sync once power on. • 12Hour : Try to sync every 12 hours. • 24Hour : Try to sync every 24 hours. • Time Zone : Select Standard time [6] Apply : Save and apply time / date setting. 3-3.
K9-a Series Manual • Hard Disk : Permission to set Hard Disk • Search : Permission to search • Backup : Permission to back up • PTZ Setting : Permission to control PTZ • PTZ OSD Menu : Permission to access PTZ OSD menu • Record Key : Permission to use Emergency Recording Key • Camera : Permission to see the selected channel [3] Detailed setting on each channel • V – Show both video and OSD • NC - Show video but hide OSD • C - Hide video but show OSD • B - Hide both video and OSD 3-4.
K9-a Series Manual • Hard Disk 1~2 : Display the hard disk capacity internally mounted • E-SATA : Display the capacity of E-SATA • Delete : Select a disk and format(delete) it [2] Total : Display total capacity and used capacity of Hard Disk [3] Over write : Record continuously by overwriting the hard disk [4] Erase Data : Format hard disks by type • Main Disk : Format all the mounted disks named “Main disk” • Mirror Disk : Format all the mounted disks named “Mirror Disk‟ [5] Auto Delete : Keep the record
K9-a Series Manual [1] Default Setup : Except major configuration (Network, Password), parameters are initialized. [2] Factory Setup : All parameters are initialized. 3-6. Upgrade [1] Firmware Update : In order to update system firmware with USB memory stick, the firmware file must be saved in the USB‟s root folder and then insert to DVR to start the update from the menu. Save a firmware USB Memory Stick [Note] Do not turn off power or remove USB stick while the upgrade is in progress.
K9-a Series Manual • Auto key lock : When there is no key input during selected period of time, system will lock keys automatically. In order to unlock, the user need to input the password. (10 sec., 30 sec., 1 min., OFF) • Key Beep : When you set this function „ON‟, a beep will sound as you press a button. 3-8. RS-485 In order to use the PTZ camera or control keyboard, user need to set RS-485 setting properly. Baudrate /Parity /Stopbit : Refer to the manual of keyboard or PTZ camera. ▒ Chapter 4.
K9-a Series Manual [1] Camera Title : ON / OFF [2] Status Bar : ON / OFF. [3] Multiscreen Border : ON / OFF. [4] Display Lock : Select a display lock option • Off : Display live image after reboot. • On : Does not display live image after reboot until user put in login information. [5] Menu Lock : Select a log in option. • Enable : Menu is locked after reboot. • Disable : Menu is NOT locked after reboot. 4-2. Split Mode DVR provides various split modes when you press the “QUAD” button.
K9-a Series Manual • Default 16 split mode. • Select 16 split mode then press “QUAD” button to setup 16 split mode. 13 Split mode (For 16Ch Model) • 13 split mode provides 2 different group of display. • Select 13 split mode and press “QUAD” button to display 13 split mode on the screen. Press “Right” direction button to select the group 1 or group2.
K9-a Series Manual • 9 split mode provides 2 different group of display. • Select 9 split mode and press “QUAD” button to display 9 split mode on the screen. Press “Right” direction button to select the group 1 or group2. 6 Split mode (For 9/16Ch Model) • 6 split mode provides 3 different group of display. • Select 4 split mode and press “QUAD” button to display 4 split mode on the screen. Press “Right” direction button to select the group 1, group2 or group.
K9-a Series Manual • 4 split mode provides 4 different group of display. • Select 4 split mode and press “QUAD” button to display 4 split mode on the screen. Press “Right” direction button to select the group 1, group2, group 3 or group 4. 4-3. Auto sequence • Auto Loss Skip : If there is no video input at certain channel, it will skip the channel. This function does not work in multi-channel sequence. • Display time : Select display duration while sequencing (1 sec. ~30 sec.
K9-a Series Manual Control spot output on rear panel. By using additional monitor, event triggered video display and sequence display are available. [1] Mode • Sequence : Display videos of selected channels in order. • Event : Display event triggered channel. • Seq+Event : If an event is triggered, it shows the triggered video first and then videos display in sequence. [2] Display Time : Set time per channel applied in sequence display. 4-5.
K9-a Series Manual 5-1. IP Address This setup allows user to connect DVR to the network so that it can be viewed at remote location. The user must know whether their internet is dynamic IP (DHCP) or fixed (static) IP. Please check with your Service Provider (ISP) before setup. [1] DHCP : “ON” for dynamic IP user. “OFF” for static IP user. [2] IP Address : Input the IP address. [Example] • IP address : 61.250.152.050 • Subnet Mask : 255.255.255.000 • Gateway : 61.250.152.001 • DNS Address : 164.124.101.
K9-a Series Manual E-mail Setup It‟s a basic setup to send email, so if it is not correct, email cannot be delivered. So be careful to make Setup correctly. [1] SMTP Server : Enter email server address to use as SMTP server. If you don‟t know the server address, contact a person who manages SMTP server you use. [2] Mail From : Enter the email address which you use. (It is for preventing a mail blocked as spam.
K9-a Series Manual Select which type of notifications you are going to use. Notification type : You can select the type for email notification. • Alarm : Email is sent with still image when an alarm occurs. • Sensor : Email is sent with still image when triggering a sensor • Motion Detection : Email is sent with still image when detecting a motion. • Video Loss : Email is sent when video input is lost. • Power On : Email is sent when DVR boots up.
K9-a Series Manual Free DDNS service is provided by KT&C DVR products. [1] Go to http://www.ktncddns.net and register your DVR using your DVR‟s Web Code. The Web Code can be found in „System – Information‟ menu.
K9-a Series Manual [2] Create your own domain name and register. [3] After registering is successful, log onto your DVR remotely by using registered IP address. Ex) http://myfirstconnection.ktncddns.com 5-6. Dual Codec Setup It is available to transmit data through extra network transmission codec. Split Resolution is for multi channel mode and Popup Resolution is for single channel full screen.
K9-a Series Manual • Channel : Channel selection • Covert : camera covert setup · On : It doesn‟t display the image · Off : Display the image • Brightness : Brightness control • Contrast : Contrast control • Saturation : Black/White control • Hue : Magenta and Cyan control 6-2. Camera Title Input a camera title using by virtual keyboard. Press a space bar to change a language. 6-3.
K9-a Series Manual [1] Channel : Select a channel [2] ON/OFF : Enable or disable to use PTZ. [3] MODEL : Select the PTZ protocol or, model [4] ID : Select the PTZ ID. (For more detail, refer to the manual of PTZ device.) Advanced [1] Reverse Control (Pan) : Set the Pan works reverse direction. [2] Reverse Control (Tilt) : Set the Tilt works reverse direction. [3] Touring Mode • Preset Touring : Use touring by DVR setting. • Camera Touring : Use touring by camera setting.
K9-a Series Manual The touring number is selectable 1~16. [1] Touring number : Select the number. [2] Preset number : Select the preset number saved before. [3] Touring interval : Select the touring dwell time in seconds. [NOTE] PTZ protocol selection Protocol is PTZ moving driver. The protocol is registered as per the camera model name or protocol name. Please check whether your PTZ is usable for this DVR. The touring is supported when the camera itself supports the touring function.
K9-a Series Manual • When you select PTZ button, + shape icon appear. Then move to the channel you want by the direction key. (2) If you moved to PTZ channel, then after pushing “SET UP” button, select the menu to operate. • Pan Tilt : Control the direction by the direction key in remote controller. • Preset : Input the preset number to set or call.
K9-a Series Manual (Preset Save) (Preset moving) • Tour : It activates saved tour number. • MENU : It calls the PTZ OSD menu. • Channel : Change channel at split screen. Available to move with direction button after selecting a channel. (Only work on split screen) • Auto Focus : Adjust the focus automatically. • Exit : Escaping the PTZ mode. ▒ Chapter 7. Record ▒ 7-1. Record Setting Set resolution, quality, recording frame rate and audio.
K9-a Series Manual [1] Channel : Set channel [2] On/Off : Set 'On' or 'Off' for recording [3] Resolution : Set resolutioin [4] Quality : Set picture quality of recorded video [5] Frame Rate : Set record frame rate [6] Post-Recording : Set recording duration time after an event is triggered. [7] Audio : Set On or Off for audio recording [8] Total Frames : It shows the occupied frames from total record frames. 7-2. Weekly Record Set schedule record per day of the week, time and channel.
K9-a Series Manual [How to setup] • Select a channel • After selecting the day of the week and time, every mouse click toggles between different modes N(Grey) → C(Green) → M(Blue) → S(Red) → M+S(Yellow) • After selecting the other day of the week and time, every OK button click makes color shift. • Clear : Delete the schedule change of the selected channel • Channel to Copy : Copy the current channel‟s recording schedule to the another selected channel.
K9-a Series Manual ▒ Chapter 8. Event Setup ▒ 8-1. Sensor It is for sensor setup. [1] Sensor Input : Select the sensor input channel. [2] On/Off : Select the sensor usage. [3] Input Type : Select the sensor input type. • N/Open (NORMAL OPEN) : The contact is normally open but close when the signal is generated. • N/Close (NORMAL CLOSE) : The contact is normally closed but open when the signal is generated. [4] Related camera : Select the camera to be related with sensor. Multi-selection is possible. 8-2.
K9-a Series Manual The cursor moving by the direction key and if press “enter”, this block is designated for motion detection. • MD selected area : Pink color • MD non-selected area : Transparent • If the movement is detected, the color of that area turns green. [Apply to all] If you use the following key, you can apply or release in one button “No1” button : Release all “No 2” button : Select all. [Using mouse] To select area, locate the mouse pointer on start position and drag to the ending point.
K9-a Series Manual • Channel : Select the channel to apply. • Preset channel : Select the preset camera being applied for the event. • Preset number : Select the preset number to move. • Popup Channel : Select the usage Popup usage by ON/OFF. • Popup Duration : Popup window floating time. • Relay out : Select the alarm out • Relay duration : Relay out duration. • Internal buzzer : Internal buzzer usage. [2] Sensor : It is the setup for PTZ, pop-up, relay out, buzzer in sensor triggering.
K9-a Series Manual • Relay duration : Relay out duration. • Internal buzzer : Internal buzzer usage. [3] Video loss : It is the setup for PTZ, pop-up, relay out, buzzer in video loss. • Channel : Select the channel to apply. • Preset channel : Select the preset camera being applied for the event. • Preset number : Select the preset number to move. • Popup Channel : Select the usage Popup usage by ON/OFF. • Popup Duration : Popup window floating time.
K9-a Series Manual · Calendar search : It allows to search by calendar. · Date /Time search : It allows to search for specific Date/Time. · Event search : It allows to search by events. · Go to first : It allows to search the first recorded data on HDD. · Go to last : It allows to search the last recorded data on HDD. 9-2. Calendar search It searches by calendar. [1] If there is recorded data on specific date, it shows red color on the date. Using the direction key, you can change YEAR/MONTH/DATE.
K9-a Series Manual 9-3. Date/Time search If you know the specific date/time to search, input the date/time to search. [1] Record Begin : It shows the first recorded data. [2] Record End : It shows the last recorded data. [3] Channel : Select the channel to search. [4] Play Begin : Input the time to search. [5] Play : When you click “Play”, it will start playback.
K9-a Series Manual 9-4. Event search It searches for event data. [1] Disk : Select recorded data location. [2] Day : Select date of the event. [3] Channel : Select the channel to search. [4] Event Type : Select type of event you want to search for. [5] Play : When you click “Play”, it will start playback. 9-5. Go to first / Go to last It searches the first or last recorded data.
K9-a Series Manual 9-6. Search Control [Control by mouse] Description of search button [1] Real-time playback [2] Pause [3] Stop [4] Reverse playback [5] Playback speed control [6] Reverse playback speed control [7] Audio during playback [8] Calendar search during playback [9] Mark In-Mark Out : If you click it during playback, it recognizes as a backup start time and if you click it once again, it recognizes as a backup end time. After this, it moves to the backup menu automatically.
K9-a Series Manual [1] Menu recall : When you select the “Audio Out” during the live or playback, the audio menu will show up. The menu call is possible by both remote controller and mouse. [2] Mode selection • OFF : No audio use. • CH1 : Audio out only from CH1 • CH2 : Audio out only from CH2 • CH3 : Audio out only from CH3 • CH4 : Audio out only from CH4 • Auto : Only selected channel audio out. • Volume control : As the length of bar increases, the volume increases. ▒ Chapter 10. Backup ▒ 10-1.
K9-a Series Manual [2] Select the date from Calendar. [3] Select the hour. [4] Select the minute. Once you select “Start“, the backup start time will be automatically input.
K9-a Series Manual [5] Backup end time selection • If the backup end time is the same hour, select the minute and click, “end“, the backup end time will be automatically input. • If the backup end time is the different hour, go back to the previous menu by right click or “MENU” button. Then, select the hour/minutes and click “end“ for automatic time input. [6] Camera : Select channels to be archived.
K9-a Series Manual [8] Before backup, it shows the USB port used, backup time, and various backup options. • Log Backup : The log file will be saved together. • Password : Backup data can be protected by the password. • Backup Format : Select type of backup file. - Executable format : Video data will be saved with its own built-in viewer. - Video Format : Only raw video data file will be saved without viewing software.
K9-a Series Manual [10] When the backup is complete, you will see the below icon as a file in USB stick. When you run it, the playback starts. [11] How to use the viewer program (If you click the backup file, it runs automatically). ① Scroll bar : It shows the current location from the total playback time. ② Open : To open another backup file.
K9-a Series Manual ▒ 11. Mobile Viewing by iPhone ▒ 11-1 Install App Go to Apple Store and download „KVRmobile‟. Then install the KVRmobile. 11-2 Execute the program When the installation is complete, the following icon is created. Select the icon to execute.
K9-a Series Manual 11-3 Register Remote Site information Enter the network information to access the DVR with iPhone. [1] Register Execute the app in iPhone and click “New” to add a remote connection. [2] Enter Name. Any name can be used for „Name‟ section.
K9-a Series Manual [3] Select the type of device [4] Enter the DVR ID and Password.
K9-a Series Manual [6] DDNS – This function shouldn‟t be used and must be set to „OFF‟ position at all time. After setting all, press “ADD” to save. 11-4 Live monitoring [1] Click the registered “DVR Name”.
K9-a Series Manual [2] Connect remotely For a channel selection, click “CH SELECT” to select a number. Relay can be controlled remotely. Click “PTZ” to control Pan/Tilt/Zoom of PTZ camera. Disables display of time, resolution, channel, etc. and displays the video only. When selected, it transmits still images with certain intervals in case video streaming is interrupted due to the network load. ☞ See full single channel screen : If you rotate iPhone to one side, it‟s switched to full screen.
K9-a Series Manual [1] Select Date/Time After selecting a date, select “SEARCH”.
K9-a Series Manual Switch to Live 11-6 Relay out Relay can be controlled remotely. Time selection : Set the duration of alarm output Off : Alarm off Infinity : Keep the alarm output continued. 11-7 PTZ control PTZ control is available on iPhone.
K9-a Series Manual (1) Select (2) Cancel (3) Automatic camera focus (4) Call the PTZ menu (5) Direction button (6) Camera focus control (7) Camera zoom control (8) Select the channel (9) Relay out button (A user can set relay out) (10) Select the PTZ menu (11) OSD display On/Off button for live screen ▒ 12. Mobile Viewing by Android phone ▒ 12-1 Install the program To install the program on the Android phone, run „Play Store‟ app and download the „KVRmobile‟ to install.
K9-a Series Manual screen. (1) (2) (3) 12-2 Execute App Select “KVRmobile” to execute. (Select the icon) (Executed Program) 12-3 Register the remote site information Register the remote site information for remote viewing.
K9-a Series Manual Select “Add” to start the registration. [2] Enter the DVR information (1) (2) (3) (1) Enter the name, User, Password, and Port information. Name : Enter any name you want. User : Enter the “User ID” registered to the DVR. Password : Enter the “Password” registered to the DVR. (Note : “Menu” → “System” → “Password) IP : Enter IP address. Port : Enter port number. (Default : 3000) DDNS Use : This function shouldn‟t be used and must be set to „OFF‟ position at all time.
K9-a Series Manual 12-4 Modify/Delete of Registered Information If you want to modify or delete the registered information, select the triangle-shaped icon. Select to edit the registered info. Select to delete the registered info. Close Tool menu (As a dual function, it ends the connection) 12-5 Remote connection Select the registered DVR list for connection.
K9-a Series Manual brief information. When you click the red-colored background, detailed information would appear. Click OK to execute the viewing program. (Select the list) (Detailed information) 12-6 Live Live shows the streaming of video from each camera in real-time. (1) Number : The channel number currently displayed is shown with bold white. When you select a channel, selected channel is displayed in full screen.
K9-a Series Manual different by model.) (2) OSD : You can turn on or off the display for channel number, date, time, event, etc. (3) I frame : It transmits still images with certain intervals in case video streaming is interrupted due to network load. (4) Audio : When you select a channel, you can listen to the audio of selected channel. 12-7 Multi-screen Live monitoring by 4 split multi-screen is available. (1) Move to previous split mode.
K9-a Series Manual Go back to the previous step or close the connection. Move to live mode (Channel change, 1 Frame and OSD display is available) Go to PTZ mode Go to PTZ preset mode Go to search mode Go to alarm mode Screen Capture App registered info.
K9-a Series Manual 12-9 PTZ You can control the PTZ camera remotely. (Select PTZ mode) (PTZ mode screen) (1) Go to PTZ mode Select the PTZ connected channel and click the PTZ button. (2) How to control PTZ The PTZ camera moves to the selected direction.
K9-a Series Manual Call the PTZ menu Auto Focus OK button for PTZ OSD menu Cancel or the upper menu on PTZ OSD menu 12-10 PTZ Preset You can set the movement of PTZ camera previously and make the automatic PTZ movement. (Select preset mode) (Preset mode screen) (1) How to go to preset mode Select the PTZ connected channel and click the Preset button. (2) How to operate Preset • Move : If you select “Move” and press a number, then the camera moves.
K9-a Series Manual 12-11 Search (1. Select the search mode) (2. Select “Time Search”) (3. Select the date and time) (1) Select the search mode (2) Select “Time Search” : Select “Time Search” to enter the search conditions. (Note : Select “To Live” to return to the live mode during the search.) (3) Enter the date and time : Select the date and time and click “Start Search” for search.
K9-a Series Manual 12-12 Relay Out Relay can be controlled remotely. (1) Relay : Select On or Off (2) Number : Select the relay number. (3) Time : Select the duration time. 12-13 Screen Capture This function allows to save current screen capture. The screenshot will be saved into your SD card.
K9-a Series Manual 12-14 Information display It shows the information of current connection. (Select info) (Display the connection information) [Display Info] Below is the example for an explanation. • IP : 61.250.157.37 : 2000 Via DDNS ← Connected IP information. • Web code : H6F60CAD00003245 ← Product ID (Webcode). • Firmware : 100, Network : 23 ← Firmware and Network Device version.
K9-a Series Manual (Select the back button) (Select the Yes button) There are several ways to finish the program. 1. When you click „Back‟, a message will pop up as “Do you want to disconnect?” You may click „Yes‟. 2. You may just press close button on the phone.
K9-a Series Manual ▒ 13.
