ORCHESTRO Instructions for use
Contents Description Operating controls and indicators 5 5 Safety recommendations 6 Limits for use 6 Configuration of the appliance 1. Adjustment and memorisation of water hardness 2. Setting the appliance to switch itself off automatically 7 7 9 Preparing the appliance before first use 1. Filling the water tank 2. Filling the heating circuit 3. Rinsing the circuit 10 10 11 12 Preparation of an espresso coffee 1. Using coffee beans 2. Using ground coffee 3.
j i k h l m n B1 B2 B1 o a g h b i j g d d c l c p f e B2 m e q b f k a r Krups Orchestro 4 KRUPS Operating controls and indicators Appliance parts B1 a. b. c. d. e. f. g. h. i. j. k. l. m. n. o. p. q. r. a. : «on/off» control and indicator light b. : «rinse» control and indicator light c.
Safety recommendations m Configuration of the appliance • Please read the following instructions carefully before using this appliance: 1. Adjustment and memorisation of water hardness • Only plug in the appliance to a socket which is earthed. Check that the voltage rating indicated on the information plate on the appliance matches that of your household electrical wiring system.
Indicator Lights Indicator Lights You have now determined the hardness of your water between 0 and 4. • Record the level of hardness by pressing the control (3). 3 The level of hardness has been pre-set at the factory to «3».To modify this, proceed as follows:- If the hardness setting is not recorded within 30 seconds, the indicator lights go out and the preceding hardness setting recorded remains in the memory.The memorisation of this setting remains valid even if there is a power cut.
Indicator Lights Time Cancel Setting indicator light Indicator light corresponds to the time selected 1 hour 3 hours • Pour in cold drinking water at least until the float in the tank reaches the upper level (8). For constant use, it is advisable to fill the tank up to the «MAX» level. 5 hours Comes On • Replace the water tank, pressing firmly so that the valve on the base allows water to flow through. Flashes • Close the lid of the water tank.
Indicator Lights Indicator Lights Warning! 3. Rinsing the circuit 11 Rinsing is required when you first use the appliance, every time the appliance is switched on, if the temperature is too low or if the correct operating temperature has not been reached. Make sure that no foreign matter, such as the tiny stones mixed in with the coffee beans, gets into the compartment. Any damage due to foreign bodies having entered the coffee bean compartment is excluded from the guarantee. • Reclose the lid.
Indicator Lights Indicator Lights Warning! Never put more than two measures into the ground coffee channel.The channel is not a store for ground coffee. Nor should you ever pour in less than one measure, otherwise the preparation of the espresso will stop automatically. Use only ground coffee beans and not powdered coffee or instant granules. 18 The indicator light «steam» flashes. Once the preheating phase is complete, the «steam» indicator light stays on and you can now start producing steam.
Indicator Lights Indicator Lights 21 • Turn the steam/hot water selector to the position (21). • Hold the jug while the froth is produced and make sure the nozzle does not touch the bottom of the container so as not to prevent the passage of the steam. • Once the froth has been obtained, reset the steam/hot water selector to the position and remove the jug. Add the milk and the milk froth to the coffee. • Clean the frothing aid and the steam nozzle using a damp cloth immediately after frothing milk.
Indicator Lights Indicator Lights Note! When the indicator light «empty collector» is on or flashing, the appliance will not operate. - The steam nozzle: Warning! The nozzle may still be burning hot.Take care not to burn yourself. Do not remove or replace the nozzle if it is still hot. • Empty the tray when the full indicator reaches the marking (25).
Indicator Lights Indicator Lights 29 • Start the cleaning programme by pressing the control for about 3 seconds (29). Note! The indicator lights «on/off», «empty collector» and «clean» are lit. Add water to the tank and cleaning will continue automatically. If the tray is not in place you will be warned of this by the flashing of the «empty collector» indicator light. Put back the tray for the cleaning programme to continue automatically. • Empty the tray and the coffee collector then replace them.
Indicator Lights Indicator Lights 32 • Start the desclaing programme by pressing the control for about 3 seconds (32). The «on/off» and «steam» indicator lights flash and the «descale» indicator light is lit. The «on/off», «empty collector» and «descale» indicator lights are lit. • Place a container with a capacity of at least 300ml under the steam nozzle. • Empty the tray and the coffee collector and replace them on the appliance. • Water is pumped at intervals and ejected via the steam nozzle.
Indicator Lights Practical Advice 4. Purging the heating circuit You must purge the heating circuit if there is a risk of frost (when transporting the appliance, etc). Indicator lights Causes Solutions • Plug in the appliance but do not turn it on. 34 • Place a container under the steam nozzle and turn the steam/hot water selector to the position . Indicators glow During the purge, the indicator light «steam» and the «on/off» indicator lights flash.
Problems, causes, solutions Problems Causes Supressing the «5000 espressos or coffees» signal Solutions The espresso coffee is not hot enough. The cups are too cold. Preheat the cups with hot water. Only part of the espresso coffee is running through. There is not enough ground coffee. Use the correct quantity of ground coffee. The coffee bean compartment is empty. Add coffee beans. The milk is not suitable: either out of date, wrong fat content, or too hot. Change the milk.
KRUPS PO Box 467, Slough, Berkshire, SL3 8WD.
