LSA-PLUS® Copper Connectivity Solutions For Telecommunication Networks KRONE LSA-PLUS® Series 2 & avaNTi Modules and Accessories ADC LSA-PLUS® Series 2 & LSA-PLUS® avaNTi connection systems include Connection, Disconnection, Switching modules, MDF, Cable Termination blocks, Back-Mount frames, protection systems, Enclosures and other related accessories.
LSA-PLUS® Overview The LSA-PLUS® Quick Connection System offers an integrated contact for use in all line plant and private network services.
The ADC LSA-PLUS® contact functions in the same basic manner regardless of the type of module in which it is placed. Using the LSA-PLUS® insertion tool (5), the plastic insulated copper wire or jumper (4) is inserted into the contact slot (2). The contact slot contains contact tags (3) set at a 45-degree angle to the wire.
NECTION CONTACT The 3-point Insulation Displacement Connection (IDC) method of termination gives durable and long lasting connections. 1. Insulation clamping ribs hold wires firmly in position and isolate the contact area from vibration and other forms of mechanical stress. 2. Flexible silver-plated contacts*, positioned at 45o angle across the axis of the wire, make a solid, gas tight connection. 3.
Testing ADC products and components pass through rigorous tests to maintain a high quality standard. ADC Tests Quality Results Contact resistance test The quality of LSA-PLUS® contact is not A reliability test that indicates the reaction of the compromised, even after repeated and tough loads. LSA-PLUS® contacts to a variety of test loads. Vibration resistance test Determines whether building vibrations and other load causes contact disturbance in the contacts.
LSA-PLUS® Series 2 LSA-PLUS® ELECTRICAL DATA After four days exposure to a climate of 40° C and 93% relative humidity Insulation Resistance Dielectric Strength Current Rating LSA-PLUS® CONTACT Contact Resistance ≥5x104Ohms ≥2000Vrms ≥Current carrying capacity of terminated conductor 1mΩ ≤ 5mΩ guaranteed Total Contact Resistance including Disconnection contacts Contact Spring Force for Disconnecting ≤ 10mΩ 3N (approx. 300g) contacts Peak voltage (with pulses 1.2/50µ sec) ≥ 3.
Installation for LSA-PLUS® S2 Modules 1. Fix the back mount frame in a vertical position on the MDF/ Exchange Room and ensure a safe earth connection is established, through the Bus Bar. 2. Introduce cable and strip the sheath (free conductor length should equal distance of furthest module+200MM). Then secure cable to the MDF Frame. 4. Termination of wires. a. Choose the bottom most slots on MDF to fit module. b. Hold the module about 50 mm - 80 mm from allocated position on the back mount frame. c.
LSA-PLUS® avaNTi FEATURES & BENEFITS The Space Saver The expansion of mobile communication networks, the introduction of third generation mobile phone systems (3G, UMTS) and the steady growth of IP networks, have created a demand for bandwidth Space in both access and transmission networks. This 30% in turn causes the extension of existing hubs and the installation of new hubs.
• Despite the generous jumper channels, the modules are mounted with a bare minimum pitch of 17.5mm. • The LSA-PLUS® avaNTi tag block for 100/64/128 pair comprises of 10/8 pair modules, set of side mount label holders, number plugs, stainless steel back-mount frame and fixing elements. The modules are mounted on the back mount frame and can beinstalled on the MDF verticals or cross connection cabinets/pillars. The module pitch is 17.
TECHNICAL DATA Module Specifications Contact Resistance Insulation Resistance Plastic Contact Material Contact Re-Terminations LSA-PLUS® Series 2 & avaNTi Modules and Accessories Conductor Diameter Range Insulation Diameter Range Operational Temperature Mounting Pitch Contact Stability Electrical safety ≤2.5 mΩ >50000 MΩ PBTP UL94 Rated VO Brass Alloy 0.4mm (26 AWG) 1 conductor per contact ≥ 200 re-terminations 0.5mm (24 AWG) 1 conductor per contact ≥200 re-terminations 0.
Ordering Information LSA-PLUS® Series 2 Modules and Accessories MODULES KRONE LSA-PLUS® Series 2 Disconnection Module Disconnection module for 8/10 pair with disconnection contact. Disconnect contact used for opening the circuit. Testing is possible in both directions. Can accept 3 or 5 point protection elements. 10 Pair 8 Pair Ordering Information Pack Qty. Product No.
BACK MOUNT FRAME Back Mount Frame CT Block Back Mount Frame 2/10 for cabinets and pillars. For mounting LSA-PLUS® modules 2/10. Ordering Information Description Pack Qty. Product No. Back Mount Frame 2/10 6 way 1 6901 2 006-14 Back Mount Frame 2/10 11 way 1 6901 2 006-13 Back Mount Frame Series 2 for 2/8 and 2/10 modules LSA-PLUS® Series 2 & avaNTi Modules and Accessories Back Mount Frame (stainless steel) 2/10 or 2/8 to mount LSA-PLUS® modules.
MDF Tag Block 64 & 128 Pair MDF Tag Blocks 2/ 8 for 64 pair with 8 LSA-PLUS® disconnection Modules for use on “Exchange Side“ (Switch) of MDF’s. Ordering Information Description Pack Qty. Product No. MDF Tag Block 64 pair 1 6901 1 002-11 MDF Tag Block 128 pair 1 6901 1 102-11 64 Pair 128 Pair CT Block for cross connect cabinets Ordering Information Description Pack Qty. Product No.
Protection Magazine 10 pair This provides voltage protection for 10 pairs on line side. The magazine can house up to ten 3 pole GD Tubes. Ordering Information Description Pack Qty. Magazine 10 pair Product No. 1 6089 2 023 -01 ACCESSORIES Accessories for testing telephone lines, local loop. Label holders, marking caps & disconnection plugs. TestCords LSA-PLUS® Series 2 & avaNTi Modules and Accessories Test Cords help test telephone lines and loop testing from subscriber end to exchange side MDFs.
Disconnection Plugs Used for disconnecting single subscriber line or for simultaneous disconnection of all subscriber lines in LSA-PLUS® disconnection module 2/10. Ordering Information Description Pack Qty. Product No. Disconnection Plug 1 pair 1 6089 3 055-00 Disconnection Plug 10 pair 1 6089 3 130-01 Marking Caps Ordering Information Description Marking Caps Pack Qty. 1 Product No.
Plug Numbers For identification of LSA-PLUS® S2 modules. Ordering Information Description Pack Qty. Printed 0...9 1 6900 3 017-00 Product No. Printed 10...100 1 6900 3 018-00 KRONE* Insertion Tool The insertion tool can be used for terminating wires (jumper and UGC). It can also be used to remove modules and wires from tag blocks. Ordering Information Description Pack Qty. LSA-PLUS® Series 2 & avaNTi Modules and Accessories Insertion Tool 1 Product No.
OUTDOOR / INDOOR BOXES Kronnection Box A-30 The Kronection Box A-30 is designed to accommodate up to 30 pairs both in indoor and outdoor installation. They are made of glass fiber reinforced polyester. It protects the installed devices against dust and rain water (protection according to IP 54). The box can be mounted directly on the wall or on a pole with a pole mounting bracket. Ordering Information Description Pack Qty. Box A-30 Product No.
MDF frame to terminate 600 pairs, 3.2 or 2.2 meters Preferred frame variant for 1000/600 pairs for accommodation of 10 pair LSA-PLUS® modules on the line side and 8 pair LSA-PLUS® module horizontally on system side. Ordering Information Description Pack Qty. 1 6901 2 600-15 Set of 4 verticals (Main) 1 6901 2 600-04 Set of 3 verticals (Expansion) 1 6901 2 600-03 1 6901 2 600-02 Set of 1 vertical (Expansion) MDF Frame to terminate 1000/600pairs, 3.
Ordering Information LSA-PLUS® avaNTi Modules and Accessories MODULES LSA-PLUS® avaNTi Modules Disconnection module for 8/10 pair with disconnection contact. Disconnect contact used for opening the circuit. It can accept 3 or 5 protection elements. Ordering Information Pack Qty. Product No.
MDF Tag Blocks MDF Tag Blocks 2/ 8 for 64/128 pair with 8 avaNTi disconnection modules for use on “Exchange Side“ (Switch) of MDF’s Ordering Information Description Pack Qty. Product No. LSA-PLUS® avaNTi MDF Tag Block 64 pair 1 6901 1 103-12 LSA-PLUS® avaNTi MDF Tag Block 128 pair 1 6901 1 103-13 Protection This provides both over voltage and over current protection for single pair on line side. Ordering Information LSA-PLUS® Series 2 & avaNTi Modules and Accessories Description Pack Qty.
Disconnection Plug Used for disconnecting single subscriber line or for simultaneous disconnection of all subscriber lines in LSA-PLUS® avaNTi disconnection module 2/10. Single Pair marking cap for marking important lines in LSA-PLUS® avaNTi connection or disconnection modules 2/10. Ordering Information Description Pack Qty. Product No.
Main Distribution Frames MDF is the interface between the subscriber cables coming from the local network (line side) and the switching equipment in the exchange (system side). ADC MDFs are available in a free standing version. (On request available in wall-secured version too). The MDFs are delivered pre-assembled thus minimising installation time. MDF Frame to terminate 1600 pairs*, height 3.5 meters Ordering Information LSA-PLUS® Series 2 & avaNTi Modules and Accessories Description Pack Qty.
KRONE type is NOT KRONE* It is observed that there are duplicates of original KRONE* products being sold in the market passing off as original KRONE* products. Using these duplicate products affects the functionality and quality of your network. Please ensure you use original KRONE* products for an efficient network. Original KRONE* products are sold ONLY through authorised distributors*.
LSA-PLUS® Series 2 & avaNTi Modules and Accessories www.adc.com/in Corporate Office & Factory: P B No. 5812, 10 ‘C’ II Phase, Peenya, BANGALORE - 560 058. India Ph: +91 80 2839 6101 / 6291, Fax +91 80 2372 2753 Toll Free: 1800 425 8232 For a listing of ADC India's sales office locations, please refer to our website ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis, Minnesota USA 55440-1101 Specifications published here are current as of the date of publication of this document.
