KEGERATOR CONVERSION KIT GUIDE 678 666 2001 www.kromedispense.
CONVERSION KIT GUIDE SAFETY PRECAUTIONS ● Make sure to put on safety glasses and gloves when working with chemicals ● Make sure to position the CO₂ tank in an upright direction. Keep the tank away from heat and store CO₂ Tank under 70०F ● Do not attempt to ever remove the valve in the keg ● Make sure to have a keg coupler along with a gas pressure regulator.
CONVERSION KIT GUIDE The KROME DISPENSE Conversion Kit allows you to convert an old refrigerator into a kegerator. This new addition to your bar at home can add more fun to your house parties. HOW TO GET STARTED Here are some preparation steps to use the kit correctly 1. Remove all shelves and keep bottom drawers in for steady support 2. The minimum dimensions needed for the kit to fit into the fridge are 18 inches x 28 inches. With this size, both the CO₂ and keg will fit easily inside the refrigerator. 3.
CONVERSION KIT GUIDE THE WORKFLOW The Keg is a pressurized container designed to store beer. The CO₂ Tank is designed to keep a steady supply of fresh beer at any point in time. How To Maintain The Equipment When the equipment is in regular use for a long time, there would be a build-up of beer stones & film in remnant on the hose linings and inner parts. This remnant is a breeding ground for bacteria. Hence it is absolutely essential to clean up the parts to prevent bacteria build-up.
CONVERSION KIT GUIDE COMMERCIAL KEG Knob Faucet Tower Shank Faucet Wrench Clear Beer Hose Red Air Line Coupler Co₂ Gauge 5 lb. Aluminum Tank Keg CONFIGURATION Use Shank System if mounting to door. COMMERCIAL COUPLER REQUIRES NUT & WASHER HOME BREW KEG Knob Faucet Tower Shank Faucet Wrench Clear Beer Hose Red Air Line Coupler Co₂ Gauge 5 lb. Aluminum Tank Keg CONFIGURATION Use Shank System if mounting to door.
CONVERSION KIT GUIDE TOWER KIT INSTALLATION Step 1 - Mark and Drill Mark spot on top of your freezer cabinet and drill a 1-1/2" hole straight through. Step 2: Screw Down Tower Position tower and screw all 4 screws down to freezer cabinet. DOOR KIT INSTALLATION Step 1: Mark Inside of Door Start on inside of door - Find good flat area for a hole and mark it. Step 2: Measure & Mark Measure in from the side and top. Step 3 - Transfer Measurements Transfer measurements to the outside of door and mark.
CONVERSION KIT GUIDE Step 7- Measure Thickness Measure the depth of the hole in the door and mark. Step 8 - Cut PVC Spacer (Optional) With hacksaw, cut a PVC spacer 1/8" shorter than the thickness of the hole in the door. Step 9 - Insert PVC (Optional) Insert the PVC spacer into the hole in the door. Step 10 - Connect Faucet Knob to Faucet:Connect knob into faucet and tighten. Step 11 - Connect Faucet to Shank Connect faucet to shank or tower and tighten with shank wrench. Do not over tighten.
CONVERSION KIT GUIDE Optional - Put Tubing in Heated Water This makes it very easy to attach to the hose nipples on the shank and the coupler. Step 15 - Attach Beer Line to Shank Push the thin end of the beer line into the barbed shank. Clear Beer Hose Step 16 - Fasten Hose with Clamp Slide the clamp over the barbed end of the hose and shank. Squeeze firmly to tighten. Homebrew Only - Remove Nut from Beerline In order to install the beer line onto the Homebrew coupler, the Nut needs to be removed.
CONVERSION KIT GUIDE Step 21 - Fasten Hose with Clamp Side the clamp over the hose and coupler, then squeeze firmly to tighten. Step 22 - Add Hose Clamp Slide a hose clamp over the other end of the air hose. ose Red Air H Red Air Hose Step 23 - Attach Air Line to Regulator Push that end of the air hose over the barbed end of the CO2 regulator. Step 24 - Fasten Hose with Clamp Slide the clamp over the regulator and hose. Squeeze firmly to tighten.
CONVERSION KIT GUIDE Step 29 - Open Regulator Valve Turn the regulator valve to the on position. Step 30 - Open Valve on Tank Turn the tank valve to the on position. (Counter clockwise) Step 31 - Adjust CO2 Pressure Adjust the regulator to read 10 to 12 PSI by turning the handle clockwise. Step 32 - Left Gauge Gauge on the left indicates total tank pressure. This will drop as the tank empties. Step 33 - Install Thermometer (Optional) Install the manual thermometer Step 34 - Completed . . .
CONVERSION KIT GUIDE DRIP TRAY INSTALLATION A drip tray catches overflow of beer as well as provides a stand to rest the glasses on Step 1 : Measure from Shank Mark a horizontal line on the front of the door about 12" below the shank hole Step 2: Screw on Drip Tray Mark the holes for the drip tray and put the screws into the door to hold the tray in place Step 3 : Drill Hole (Optional) About 8" under the drip tray , drill the hole straight through the door Step 4: Completed ....
CONVERSION KIT GUIDE TROUBLESHOOTING GUIDE Issue Beer and foam inconsistency Possible Causes Solution Temperature too warm Most beers have to be between 32 and 38 degrees for best consistency Lack of pour Hold the glass at 45 degrees when pouring till mid-section. Then straighten the position to fill the remaining glass. Excessive CO2 Reduce the CO2 output and remove the relief valve on the coupler. This will release the extra pressure and adjust output while pouring.
CONVERSION KIT GUIDE KEG COUPLERS A Keg Coupler is a key element of any draft beer system. It's a small but vital piece of the system that connects the gas and beverage lines to the keg and ensures a pressurized flow. Different kegs are compatible with different couplers. Krome offers wide range of couplers. Below are the different types of couplers available.
CONVERSION KIT GUIDE PREMIUM FAUCETS Time for a faucet change? Then explore our array of faucets Stainless Steel Standard Beer Faucet This faucet works perfectly well for bars and other places of heavy usage. Get ideal beer flow with non-stick ball washer. The stainless steel will not impart any off taste. Stainless Steel SelfClosing Beer Faucet The faucet optimizes beer flow and prevents unnecessary leakages with its selfclosing action upon release of the lever.
CONVERSION KIT GUIDE TAP HANDLES Krome Dispense Provide a wide range of tap handles to add a signature touch to any beer dispenser. Choose among our beautiful colored tap handles, chalkboard handles and Marble handles to match with the interiors of your pub Beer tap handles are easy to install. Simply twist the threaded handle onto the faucet lever and installation is complete.
CONVERSION KIT GUIDE Replacement Parts Are Available at us.kromedispesne.com Keg Coupler 9 10 1 7 4 6 3 5 8 Item No. 1 2 3 4 5 6 7 8 9 10 2 Part No. Description C704.03 C704.05 C704.08 C704.09 C704.10 C704.11 C181X1 C712.13 C701.50 C804.02 Coupler Body O-Ring Shanky Bottom Seel Check Valve Handle Hinge Pin Short Handle Gas Hose Nipple Crome Plated Brass Beer Hex Nut PRV D System Probe & Ball Retainer Sub-Assembly PRV Holder Beer Faucet: 2 Item No. Part No. Description 1 2 3 4 5 6 7 C201.
