R INSTALLATION MANUAL Stainless Steel Farmhouse Kitchen Sinks KHF200-30, KHF200-33, KHF200-36 KHF203-33, KHF203-36, KHF204-33 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Inspect the sink prior to installation to make sure the sink has not been damaged during shipping · Use the cut-out template provided by Kraus · Observe all plumbing and building codes according to your state requirement · Additional floor and wall preparation may be required to avoid damaging the product · Make sure to purchase the correct cabinet for your farmhouse sink.
Parts List KHF200-30 · · · Cut-Out Template Bottom Grid KBG-200-30 Basket Strainer BST-1 KHF200-33 · · · Cut-Out Template Bottom Grid KBG-200-33 Basket Strainer BST-1 KHF200-36 · · · Cut-Out Template Bottom Grid KBG-200-36 Basket Strainer BST-1 KHF203-33 · · · · Cut-Out Template Bottom Grids KBG-203-33-1 & KBG-203-33-2 Strainer ST-1 Basket Strainer BST-1 KHF203-36 · · · · Cut-Out Template Bottom Grids KBG-203-36-1 & KBG-203-36-2 Strainer ST-1 Basket Strainer BST-1 KHF204-33 · · · · Cut-Out Templa
9" 10" 16" (406mm) (254mm) 16" (406mm) Model #: KHF200-33 Sink Dimensions: 32 7/8” x 20 3/4” x 10” Min Cabinet Size: 33” 10" (90mm) 10" 32 7/8" (835mm) (254mm) 29 3/4" (756mm) (229mm) 30" (762mm) 3 1/2" (527mm) (90mm) 27" (686mm) Model #: KHF200-30 Sink Dimensions: 29 3/4” x 20 3/4” x 10” Min Cabinet Size: 30” 20 3/4" 3 1/2" (527mm) 20 3/4" 16" (406mm) (527mm) (90mm) (254mm) 9" 3 1/2" (229mm) 20 3/4" Dimensions: 33" (838mm) 9" (229mm) 35 7/8" (911mm) Model #: KHF200-36 Si
16" 13" (330mm) 9" 10" (229mm) 35 7/8" (911mm) 16" (406mm) (254mm) Model #: KHF203-36 Sink Dimensions: 35 7/8” x 20 3/4” x 10” Min Cabinet Size: 36” 10" (527mm) 20 3/4" (295mm) (406mm) (295mm) 7/8" (835mm) 10" 19" (483mm) Model #: KHF203-33 Sink Dimensions: 32 7/8” x 20 3/4” x 10” Min Cabinet Size: 33” 11 5/8" (90mm) (254mm) 11 5/8" (229mm) 32 3 1/2" (527mm) 16" 17 3/8" (442mm) 9" (406mm) (90mm) (254mm) (527mm) 20 3/4" 3 1/2" 20 3/4" Dimensions: 17 3/8" (442mm) 9" (229m
Step 1. Measure & Build Supports · · Measure the actual height of apron. Build supports on inside of cabinet based on sink measurements.
Step 2. Cut Cabinet Front · Measure height of apron front. Add 1/16" to the dimension when you mark base cabinet front cutout. Use jigsaw to cut. Step 3. Install Sink · · · Place sink in opening. The weight of sink should be sustained by the built supports. Make sure sink is leveled from front to back and side to side. Uses silicone to fill in gaps where necessary.
Step 4.
Step 5. Cut Countertop Use a bead of silicone (or preferred adhesive) around the rim of the Check the alignment of the sink to the cutout in the countertop. Place countertop cutout hole over sink and press firmly. ne A dhesi ve Installer Tip: Use acetone or denatured alcohol to remove any excess sealant.
Step 6. Install Plumbing Fixtures · · Connect drain to sink. Connect trap to drain. Connect water supply connections to faucet according to manufacturer's instructions. Run water into sink and check for leaks.
Codes/Standards Applicable UP C C R Kitchen Sink Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Kitchen Sink" in its original location. The warranty is non-transferable. Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal usage for the lifetime of the product.
If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.com If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
