INSTALLATION GUIDE Oletto™ Single Lever Bar/Prep Faucet KPF-2600 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2017 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep teh box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
7/8” (22mm) 19.7 º 10 1/8” (257mm) 8 5/16” (21mm) ∅ 1 15/16” (∅ 50mm) Prior to Installation: ∅ 1 3/4” (∅ 45mm) • ∅ 1 15/16” (∅ 50mm) 1 3/8” (35mm) Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800775-0703 for a replacement • Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List E B A F D C A. Aerator B. Faucet Body E1. 2.5mm C. Base E2. 4mm D. Hot & Cold Waterlines 3 E. Hex Wrench Set F.
Faucet Dimensions 7" (178mm) 4 1/8" (105mm) 5 9/16" (141mm) 27 5/16" (694.5mm) 36Max 7 5/16" (186mm) 12 1/4" (310.
NOTE: The mark “FR↑NT” should parallel with face basin,align to front (Otherwise, the faucet will deflect) Step 1: Install base Aligning shank with groove of washer. C Half Moon Locking Nuts F Insert base (C) into base ring (F) on sink or countertop with “FR↑NT” facing forward.
Step 3: Secure faucet Secure faucet body (B) by tightening the set screw with 2.5mm hex wrench (E) B B E C Step 3: Connect waterlines to main valve D Hot D Cold Thread hot & cold waterlines (D) onto angle stops. Tighten with adjustable wrench until snug.
C Step 4: Flush faucet A Remove aerator (A). Turn faucet on for 1 minute to flush any debris. Reconnect aerator (A) A Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM 7 CAUSE ACTION Water will not shut off completely Cartridge (5) may need to be adjusted or replaced Remove index button (1A). Loosen set screw (1B) with 2.5mm hex wrench (12). Remove metal handle (2).
Replacement Part List 10 Hexagon Nut 9 11 1. A Index Button 12 13 B Set Screw 2. Metal Handle 8 3. Cartridge Cover 7 6 4. Locking Nut Hot 5. Cartridge Water Cold Water 6. Seal Kit 7. Insert 9 8. Aerator 9. Set Screw 4 5 2 10. Base Ring 3 10 1 11. Base 12. Hex Wrench 2.5mm 13 Close 25˚ 12 13. Hex Wrench 4mm 90˚ 11 Push Open Left Hot Water Care & Maintenance *To keep the product clean & shining, follow the steps below: 1. 2. 3. 4.
Codes / Standards Applicable: GREEN LEAD FREE IA P NSF/ANSI Standard 61 certified by IAPMO NSF/ANSI Standard 372 certified by IAPMO MO Meets ASME A112.18.1M/A112.18.1 R& T 1.75gpm 6.6L/min maximum TM Water Efficiency FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. COMMERCIAL WARRANTY Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT REGISTER YOUR KRAUS PRODUCT • • • Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY www.kraususa.com/register or visit our website and click on Register Product www.kraususa.
