R INSTALLATION MANUAL Allyn Transitional Bridge Kitchen Faucet with Pull Down TM KPF-3121 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone. · Flush angle stops to release any debris prior to installation.
Diagram and Parts List 1. 2. 3. 4.
Faucet Installation Procedure 3 1/4" 8 1/8" 9 3/8" (239.07mm) (207.35mm) 7 3/4" (196.75mm) 16" (407.9mm) (83.2mm) Ø1 7/8" (48mm) Ø1 7/8" (48mm) 4" 4" (102mm) (102mm) 14 5/8" (370.4mm) Installer Tip: Shut off main water supply before installing new faucet.
Step 1. Install faucet and secure mounting hardware Secure the faucet body with the rubber and metal washers (2) and the mounting nuts and screws (3). Do not overtighten. 2 3 Step 2. Attach spray hose and weight Connect spray hose to quick connector attached to supply line. Install weight (4) on lowest vertical point on spray hose. White line on the spray hose should be in the center of the weight. 4 NOTE: Please see Step 5 on page 8 to change the flow rate of the faucet.
Step 3. Flush spray hose Remove spray head from spray hose. Hold tip of spray hose. Turn faucet on and let the water run for 60 seconds to flush any debris. NOTE: Please make sure washer is installed attaching spray head to hose.
Replacement Parts 4 7 Replacement Parts List Finish/Color Part # 1. Spray Head SFS, MB, BG* KP44010 2. Check Valve KP44011 3. Washer KP44012 4. Spray Hose 3 SFS, MB, BG* 5. Spout Washers 2 KP44013 KP44014 6. Metal Handle SFS, MB, BG* KP44001 7. Lever Button SFS, MB, BG* KP44002 8. Cartridge Cover SFS, MB, BG* KP44003 5 1 6 8 10 9 11 9. Cartridge Hot KP44004-H 10. Cartridge Cold KP44004-C 11. Base O-Ring KP44005 12. Rubber Washer KP44006 13. Metal Washer KP44007 14.
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose or cartridge needs to be reseated. Remove button located at top of handle. Loosen set screw with hex wrench. Remove handle and unscrew cartridge cover by hand. Tighten locking nut with an adjustable wrench. Water does not shut off Cartridge may need to be adjusted or replaced.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI 61-9 UP C R C ASME A112.18.1 1.8GPM 6.8L/min maximum C R FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
