INSTALLATION GUIDE Oletto™ Single Handle Kitchen Faucet KPF-2631 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List B I A J C D E F G H A. Sprayer B. Faucet Body C. Escutcheon D. Gasket E. Easy Install Assembly F. Weight 3 G. Weight Clip H. Quick Connector I. 2.5mm Hex Wrench J.
Faucet Dimension 10 3/4" 10 1/4" [274.6mm] 11" [279.6mm] [259mm] 9 1/8" 8 1/4" [209.5mm] [549mm] 21 5/8" 8 1/2" 2 1/2" [215.4mm] [555mm] 21 7/8" [233.2mm] 2" [52mm] 2 1/8" [54.
Step 1a: Installing the easy install assembly (Without escutcheon) Shut off the water supply. Remove the old faucet. Clean the mounting surface. Check for the proper thickness of the sink. Insert the base (a) into sink. If your model does have a escutcheon, skip to step 1 b. a b NOTE: “Front” on the base (a) must face the front of the sink. The two mounting plates (b) on the base (a) must be loose and movable during the installation of the base (a).
Step 2: Installing the easy install assembly J J a Fig 1 a C C b 1 b 1 Fig 2 J J a a C b Fig 4 1 C b Fig 3 1 Press the base (a) and escutcheon (C) so that they can not move, then turn the screws with the provided hex wrench (J, HEX: 6.0mm) clockwise, as shown Fig 1. When the mounting plates (b) make contact with the sink (1), continue to turn the screw with the provided hex wrench (J, HEX: 6.
Step 3: Installing the faucet B I 3 2 1 a Insert the hose (1)、supply lines (2) and quick connect hose (3) one by one through the hole of the base (a). Carefully insert the hoses into the base. Place the faucet assembly onto the base (a) as shown in the above figure. Secure the faucet assembly (B) by tightening the set screw with the provided hex wrench (I, Hex: 2.5 mm).
Step 4: Securing the faucet assembly Install the weight clip (G) at the point of the hose marking "weight here". Insert the weight (F) onto the weight clip (G) by sliding it down onto the weight clip (G). Weight here F Weight here G Step 5: Connect waterlines to main valve Attach waterlines to angle stops and tighten until snug.
Step 6: Flush faucet A NOTE: Please make sure washer is installed attaching sprayer to hose. 9 Pull the hose assembly out of the spout and remove the sprayer (A) by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush the water lines for one minute. This flushes away any debris that could cause damage to internal parts. Check for leaks.
Replacement Parts Replacement Parts List Finish / Color 1. Sprayer BB, CH, SFS, MB, KP27250 SFACB* 2. Washer KP27251 3. Sprayer Hose 4. Spring Assembly 5. Inverter BLBB, GRCH, KP27252 GRSFS, BLMB, BLSFACB* BB, CH, SFS, MB, KP27253 SFACB* GR, BL* 04 7. Inverter 05 06 07 02 01 12 19 10 12 13 20 17 21 14 22 23 18 9. Bonnet Nut KP27258 15 16 BB, CH, SFS, MB, KP27259 SFACB* BB, CH, SFS, MB, KP27260 SFACB* 12. Screw 11 KP27256 KP27257 11. Handle 09 GR, BL* 8. Cartridge 10.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following coorective steps: PROBLEM CAUSE Leakage under the handle Bonnet nut (9) has come loose 10 Hexagon Nut 9 11 The aerator has an irregular or reduced water flow 12 Water will not shut off completely ACTION Remove the index (13). Loosen screw (12) with hex wrench (20). Remove the handle (11) and cap (10).
Codes/Standards Applicable: NSF/ANSI 372 LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1 1.8GPM 6.8L/min maximum TM Faucet Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
Shipping charges will be covered foe the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. Commercial Warranty Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.
