INSTALLATION GUIDE Oletto™ Single Handle Kitchen Faucet KPF- 2620 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List B A I J C F D G E H A. Spray Head B. Faucet Body C. Escutcheon D. Gasket E. Easy Install Assembly F. Weight 3 G. Weight Clip H. Quick Connector I. 2.5mm Hex Wrench J.
Faucet Dimension 10 5/8'' 10 1/2'' [269.7mm] 10 1/8'' 8 7/8'' 8 7/8'' [224.6mm] [224.6mm] 7 3/8'' 7 1/8'' [187.4mm] [181.6mm] 15 1/4'' [388.8mm] [258.8mm] [265.2mm] Ø2 1/8'' [53.0mm] [59.6mm] Max: 2 3/8'' [53.4mm] Max: 2 1/8'' 2 1/2'' [62.
Step 1a: Installing the easy install assembly (Without escutcheon) Shut off the water supply. Remove the old faucet. Clean the mounting surface. Check for the proper thickness of the sink. Insert the base (a) into sink. If your model does have a escutcheon, skip to step 1 b. a b NOTE: “Front” on the base (a) must face the front of the sink. The two mounting plates (b) on the base (a) must be loose and movable during the installation of the base (a).
Step 2: Installing the easy install assembly J J a Fig 1 a C C b 1 b 1 Fig 2 J J a a C b Fig 4 1 C b Fig 3 1 Press the base (a) and escutcheon (C) so that they can not move, then turn the screws with the provided hex wrench (J, HEX: 6.0mm) clockwise, as shown Fig 1. When the mounting plates (b) make contact with the sink (1), continue to turn the screw with the provided hex wrench (J, HEX: 6.
Step 3: Installing the faucet B I 3 2 1 a Insert the hose (1)、supply lines (2) and quick connect hose (3) one by one through the hole of the base (a). Carefully insert the hoses into the base. Place the faucet assembly onto the base (a) as shown in the above figure. Secure the faucet assembly (B) by tightening the set screw with the provided hex wrench (I, Hex: 2.5 mm).
Step 4: Securing the faucet assembly Install the weight clip (G) at the point of the hose marking "weight here". Insert the weight (F) onto the weight clip (G) by sliding it down onto the weight clip (G). Weight here F Weight here G Step 5: Connect waterlines to main valve Attach waterlines to angle stops and tighten until snug.
Step 6: Flush faucet A NOTE: Please make sure washer is installed attaching sprayer to hose. 9 Pull the hose assembly out of the spout and remove the spray head (A) by unscrewing it from the hose in a counterclockwise direction. Be sure to hold the end of the hose down into the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush the water lines for one minute. This flushes away any debris that could cause damage to internal parts. Check for leaks.
Replacement Parts Replacement Parts List Finish / Color 1. Spray Head BB, CH, SFS * 2. Washer 3. Spray Hose 3 5 6 2 15 1 7 17 8 9 10 13 11 12 19 20 KP27296 KP27208 BLBB, GRCH, GRSFS* KP27290 4. Quick connector assembly KP27090 5. O-Ring KP27210 6. Inverter KP27211 7. Cartridge KP27257 8. Bonnet Nut KP27258 9. Cap BB, CH, SFS * KP27259 10. Handle BB, CH, SFS * KP27260 KP27001 11. Set Screw 18 Part # 12. Cover Button GR, BL* KP27002 13. Weight & Clip Assembly KP27212 14.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following coorective steps: PROBLEM CAUSE Leakage under the handle Bonnet nut (9) has come loose 10 Hexagon Nut 9 11 The aerator has an irregular or reduced water flow 12 Water will not shut off completely ACTION Remove the cover button (12). Loosen set screw (11) with hex wrench (15). Remove the handle (10). Unscrew cap (9) (by hand only).
Codes/Standards Applicable: NSF/ANSI 372 LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1 1.8GPM 6.8L/min maximum TM Faucet Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
Shipping charges will be covered foe the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. Commercial Warranty Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.
INSTALLATION GUIDE Purita™ Single Handle Water Filtration Faucet FF-100 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List A G B C D E F A. Faucet Assembly B. Flange C. Rubber Washer D. Metal Washer E. Mounting Nut F. Connector G.
Faucet Dimension 7 1/8” 2 3/4“ [181.5mm] [69.5mm] 6” 8 3/8“ [212.0mm] 12” [304.5mm] [153.0mm] Ø1 3/4" [Ø45.0mm] [77.
Step 1: Preparing for installation Remove the rubber washer (C), metal washer (D), and mounting nut (E) from the end of the stud. C D E Step 2: Installing the faucet assembly A C D E 5 Place the faucet assembly (A) through the selected hole in the sink or countertop. On the underside of the sink or countertop, slide the rubber washer (C) and metal washer (D) onto the stud. Thread the mounting nut (E) onto the stud, and tighten securely using your wrench.
Step 3: Connecting the quick connect adaptor and water line A Thread the quick connect adaptor (F) onto the end of the faucet assembly (A) stud, and tighten securely using a wrench. Connect the 3/8 in. water line from the filtration system by pushing the line into the connector (F). Pull down on the 3/8 in. line slightly to ensure the quick connect fitting has engaged. F 3/8 in.
Replacement Parts 1 Replacement Parts List Finish / Color 1 2 3 4 5 CH, SFS, MB, BG, KP27169 BB, SFACB, SFSB* 3. Locking Ring KP27170 4. O-ring KP27171 5. Cartridge KP27172 6. Handle CH, SFS, MB, BG, KP27173 BB, SFACB, SFSB* 7. Index GR, BL* 8. Flange CH, SFS, MB, BG, KP27174 BB, SFACB, SFSB* KP27194 9. Rubber Washer KP27175 10. Metal Washer KP27176 11. Mounting Nut KP27177 12. Connector KP27178 13.
10 Trouble - Shooting 9 Hexagon Nut 11 If you have followed the instructions carefully and your faucet still does not work properly, take the following coorective steps: 12 PROBLEM C A U S13E ACTION Leakage under the handle Cartridge (5) has come loose Remove index (7) and loosen set screw with hex wrench (13). Remove the Cold handle.
Codes/Standards Applicable: NSF/ANSI 372 LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1 1GPM 3.8L/min maximum TM Faucet Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (”Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
Shipping charges will be covered foe the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. Commercial Warranty Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.
