R INSTALLATION MANUAL Oletto Single Lever Pull Down Kitchen Faucet TM KPF-2620 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone. · Place bucket under angle stops.
Diagram and Parts List A. B. C. D. E. F. G. H. I. Spray Head Faucet Body Deck & Putty Plate Supply Hose Hot & Cold Waterlines Spray Hose Weight Quick Connect Hex Wrench i1. 2.5mm i2. 4mm J. Base B A C J D E F I G H For technical assistance or replacement parts, please contact Kraus Customer Service and one of our representatives will be happy to help: 4 Toll-Free: 800-775-0703 or Customerservice@kraususa.
Faucet Dimensions 10 3/8" (263mm) 4 1/4" (109mm) 8 3/4" (387mm) (193mm) 7 5/8" (186mm) 15° 15 1/4" 1/2" (11.3mm) 7 3/8" 90° (663mm) 25° 23° 26 1/8" (223mm) 7/8" (22mm) MAX 1 1/2" 2 3/8" (38mm) (61.5mm) Check Value 3/8''Compression Ø1 3/8" (35mm) 2 3/8" (61.5mm) 10 1/4" (261mm) 1/2" (11.3mm) * Optional Deck Plate Installer Tip: Shut off main water supply before installing new faucet.
Step 1A: Install base without deck & putty plate Insert base (J) into sink or countertop with “FR↑NT” facing forward. Tighten screws on base (J) with 4mm hex wrench (i2) until base is secure on sink or countertop. J Half Moon Locking Nuts Installer Tip: Rotate the two half-moon shaped locking nuts inward before inserting base (J) into sink or countertop. i2 Step 1B.
Step 2. Install Faucet E E D Remove Quick Connect (H) from spray hose (F). Insert spray hose (F) into small hole of base (J). Insert hot & cold waterlines (E) and supply hose (D), one by one, in large hole of base. F FE D D Step 3. Secure Faucet Align arrow on faucet body (B) with arrow on base (J). Attach faucet body (B) to base (J). Secure faucet body (B) by tightening the set screw with 2.5mm hex wrench (i1).
Step 4. Connect waterlines to main valve E Thread hot & cold waterlines (E) onto angle stops. Tighten with adjustable wrench until snug. Turn on the angle stops and check for leaks. DO NOT TURN FAUCET ON E E Hot Cold Installer Tip: Use two wrenches when securing waterlines to angle stops to prevent kinking, as shown in picture Step 5. Connect quick connect D F D F D H F 8 Attach Quick Connect (H) with black end onto spray hose (F) until you hear a click.
Step 6. Install weight Attach weight (G) on the designated mark on the spray hose (F). Designated Mark F G Step 7. Flush faucet Remove spray head (A). Hold tip of spray hose (F). Turn faucet on for 1 minute to flush any debris. Reconnect spray head (A).
Replacement Parts Replacement Parts List Finish/Color 1. Spray Head CH,SFS,BB* KP07002 KP07182 2. Washer 3. Hose Guide 3 2 4 1 6 5 11 7 8 10 9 KP07183 KP07129 5. Set Screw KP07124 6. Cartridge KP07047 7. Locking Nut KP07102 8. Cartridge Cover CH,SFS,BB* KP07101 9. Handle Assembly CH,SFS,BB* KP07100 CH,SFS,BB* KP07011 10. Escutcheon KP07000 Assembly 14 15 12. Spray Hose KP07121 13. Weight KP07001 14. Base KP07005 15. Hex Wrench Set KP07109 (2.
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose or cartridge needs to be reseated. Remove button located at top of handle. Loosen set screw with hex wrench. Remove handle and unscrew cartridge cover by hand. Tighten locking nut with an adjustable wrench. Water does not shut off Cartridge may need to be adjusted or replaced.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI 61-9 UP C R C ASME A112.18.1 1.8GPM 6.8L/min maximum C R FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
INSTALLATION GUIDE Purita™ Single Handle Water Filtration Faucet FF-100 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product: DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available, and retain a copy of your receipt with purchase date for reference.
Prior to Installation: • Make sure you have all necessary parts by checking the diagram and parts list.
Diagram and Parts List A G B C D E F A. Faucet Assembly B. Flange C. Rubber Washer D. Metal Washer E. Mounting Nut F. Connector G.
Faucet Dimension 7 1/8” 2 3/4“ [181.5mm] [69.5mm] 6” 8 3/8“ [212.0mm] 12” [304.5mm] [153.0mm] Ø1 3/4" [Ø45.0mm] [77.
Step 1: Preparing for installation Remove the rubber washer (C), metal washer (D), and mounting nut (E) from the end of the stud. C D E Step 2: Installing the faucet assembly A C D E 5 Place the faucet assembly (A) through the selected hole in the sink or countertop. On the underside of the sink or countertop, slide the rubber washer (C) and metal washer (D) onto the stud. Thread the mounting nut (E) onto the stud, and tighten securely using your wrench.
Step 3: Connecting the quick connect adaptor and water line A Thread the quick connect adaptor (F) onto the end of the faucet assembly (A) stud, and tighten securely using a wrench. Connect the 3/8 in. water line from the filtration system by pushing the line into the connector (F). Pull down on the 3/8 in. line slightly to ensure the quick connect fitting has engaged. F 3/8 in.
Replacement Parts 1 Replacement Parts List Finish / Color 1 2 3 4 5 CH, SFS, MB, BG, KP27169 BB, SFACB, SFSB* 3. Locking Ring KP27170 4. O-ring KP27171 5. Cartridge KP27172 6. Handle CH, SFS, MB, BG, KP27173 BB, SFACB, SFSB* 7. Index GR, BL* 8. Flange CH, SFS, MB, BG, KP27174 BB, SFACB, SFSB* KP27194 9. Rubber Washer KP27175 10. Metal Washer KP27176 11. Mounting Nut KP27177 12. Connector KP27178 13.
10 Trouble - Shooting 9 Hexagon Nut 11 If you have followed the instructions carefully and your faucet still does not work properly, take the following coorective steps: 12 PROBLEM C A U S13E ACTION Leakage under the handle Cartridge (5) has come loose Remove index (7) and loosen set screw with hex wrench (13). Remove the Cold handle.
Codes/Standards Applicable: NSF/ANSI 372 LEAD FREE IA P MO R& T NSF/ANSI 61 ASME A112.18.1 1GPM 3.8L/min maximum TM Faucet Warranty Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. (”Kraus”). Kraus extends this warranty to the original purchaser for personal household use of the “Faucet” in its original location. The warranty is non-transferable.
Shipping charges will be covered foe the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included. Commercial Warranty Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use. All incidental or consequential damages are specifically excluded.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration www.kraususa.