R INSTALLATION MANUAL Oletto Single Lever Pull Out Kitchen Faucet TM KPF-2610 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2018 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone. · Place bucket under angle stops.
Diagram and Parts List A. Spray Head B A J F C B. C. D. E. F. G. H. I. J. I Faucet Body Deck & Putty Plate Base Spray Hose Supply Hose Hot and Cold Waterlines Weight Quick Connect Hex Wrench Set J1. 2mm J2. 2.5mm J3.
Faucet Installation Procedure 10 3/8" (263mm) 10 1/8" 8 1/8" (258mm) 10 1/4" (261mm) 7" (179mm) 9° 9 1/2" (242mm) (207mm) Ø2" 3/8" 1/16" ~ 1" (1mm~25.4mm) 2 1/2" (63.5mm) (8.2mm) (50mm) 9/16-24UNEF 3/8" Compression Installer Tip: Shut off main water supply before installing new faucet.
Step 1A. Install base without deck & putty plate Insert base (D) into sink or countertop with “FR↑NT” facing forward. Tighten screws on base (D) with 4mm hex wrench (J) until base is secure on sink or countertop. D Half Moon Locking Nuts Installer Tip: Rotate the two half-moon shaped locking nuts inward before inserting base (D) into sink or countertop. J Step 1B.
Step 2. Install faucet Insert spray hose (E) into small hole of base (D). Insert hot & cold waterlines (G) and supply hose (F), one by one, in large hole of base. G G F F G Rubber Caps E G G F E Installer Tip: Please remove rubber caps for spray hose (E) and supply hose (F) prior to inserting into base. Installer Tip: To remove Quick Connect (I), push housing upward, hold firmly, and pull downward. Step 3. Secure faucet B J D Align arrow on faucet body (B) with arrow on base (D).
Step 4. Connect waterlines to main valve G Thread hot & cold waterlines (G) onto angle stops. Tighten with adjustable wrench until snug. Turn on the angle stops and check for leaks. (DO NOT TURN FAUCET ON) Installer Tip: Use two wrenches when securing waterlines to angle stops to prevent kinking. G G Hot Cold Step 5. Connect quick connect Attach Quick Connect (I) with black end onto spray hose (E) until you hear a click. Attach the other end onto the supply hose (F).
Step 6. Install weight Attach weight (H) on the designated mark on the spray hose (E). Designated Mark H E Step 7. Flush faucet Remove spray head (A). Hold tip of spray hose (E). Turn faucet on for 1 minute to fl ush any debris. Reconnect spray head (A).
Replacement Parts Replacement Parts List Finish/Color Part # 1. Metal Handle SFS, CH* KP07110 2. Cartridge Cover SFS, CH* KP07101 1 2 3 4 8 10 9 3. Locking Nut KP07112 4. Cartridge KP07182 5. Set Screw KP07116 6. Base KP07115 7. Escutcheon SFS, CH* KP07114 8. Spray Head SFS, CH* KP07113 9. Quick Connect KP07000 10. Spray Hose KP07117 11. Weight KP07001 12. Hex Wrench 2mm KP07067 13. Hex Wrench Set (2.
Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under faucet handle Locking nut has come loose. Unscrew joystick from handle (1). Loosen set screw with a hex wrench (12). Remove metal handle (1). Unscrew cartridge cover (2) by hand only. Tighten locking nut (3) with an adjustable wrench. Water does not shut off completely Cartridge may need to be adjusted or replaced.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI 61-9 UP C R C ASME A112.18.1 1.8GPM 6.8L/min maximum C R FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
