INSTALLATION MANUAL Oletto™ Single Handle Kitchen Bar Faucet KPF-2600 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2023 Kraus USA Plumbing LLC I Rev.
Congratulations on the purchase of your new Kraus plumbing fixture! R Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
STOP Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. R · Read all instructions and safety warnings and ensure you have all tools, parts, and equipment necessary for a safe installation. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List A C D B A. Faucet Body B. Easy Install Assembly 4 C. 6mm Hex Wrench D. 2.
Faucet Dimensions 7'' [178.7mm] 4 1/4'' 5 1/2'' [140.8mm] 7 1/4'' [184.9mm] [312.2mm] 12 1/4'' [109.1mm] 2'' [61.0mm] Max: 2 3/8'' [52.0mm] 3/8” compression Installer Tip: Shut off main water supply before installing new faucet.
Step 1a: Installing the easy install assembly Shut off the water supply. Remove the old faucet. Clean the mounting surface. Check for the proper thickness of the sink or countertop. Insert the base (a) into the sink or countertop. If your model does have a escutcheon, skip to step 1 b. a b NOTE: “Front” on the base (a) must face the front of the sink or countertop. The two mounting plates (b) b) on the base (a) must be loose movable during the installation of the base (a).
Step : Installing the a et A D 1 a nsert the supply lines (1) through the hole o the base (a). Care ully insert the hoses into the base. Place the aucet assembly ( ) onto the base (a) as shown in the above igure. ecure the aucet assembly ( ) by tightening the set screw with the provided hex wrench ( , Hex: 2. mm).
Step 4: Connect waterlines to main valve Attach waterlines to angle stops and tighten until snug. Turn on angle stops and check for leaks (DO NOT TURN FAUCET ON). NOTE: Please make sure filter washers are installed before connecting to the main valve. Step 5: Flush faucet After installing the faucet, remove the aerator. Turn the water on for 30 seconds to remove any debris. Reassemble the aerator. Do not lose the gasket (1) in the aerator.
Replacement Parts 2 3 4 1 5 6 8 11 9 1. Aerator Assembly CH, SFS, MB, BB, SFACB* KP27295 2. Washer GR, BL* KP27031 14 16 11 12 15 Part # 3. Block KP27030 4. O-Ring KP27029 GR, BL* KP27222 6. Set Screw KP27033 7. Cartridge KP27257 8. Bonnet Nut 10 17 Finish / Color 5. Index 7 13 Replacement Parts List 9. Cap 10. Handle KP27258 CH, SFS, MB, BB, SFACB* CH, SFS, MB, BB, SFACB* KP27260 KP27001 11. Set Screw 12. Cover Button KP27259 GR, BL* KP27002 13.
Troubleshooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leakage under the handle. Bonnet nut (8) has come loose. Remove the cover button (12). Loosen the set screw (11) with the hex wrench (15). Remove the handle (10) and cap (9) . Tighten bonnet nut (8) with an adjustable wrench. The aerator has an irregular or reduced water flow. The aerator is dirty or misfitted.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI/CAN 61: Q ≤ 1 UP C R C LEAD FREE IA P C MO R& R NSF/ANSI 61 T TM ASME A112.18.1 1.5GPM 5.7L/min maximum Faucet - Lifetime Limited Warranty Kraus USA Plumbing, LLC (“Kraus”) extends this warranty to the original purchaser for personal household use of the Faucet when purchased from an authorized Kraus dealer and in the location of original installation. This warranty is non-transferable.
How to Make a Warranty Claim If you are a consumer purchaser, please contact a Kraus Customer Service Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 Toll-free 800-775-0703 Customerservice@kraususa.com R If you are a plumbing contractor or trade professional, please contact a Kraus Pro Representative at: Kraus USA Plumbing, LLC 12 Harbor Park Drive Port Washington, NY 11050 516-801-8955 Proservice@kraususa.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
