R INSTALLATION MANUAL OlettoTM Single Lever Bar/Prep Faucet KPF-2600 www.kraususa.com I Toll Free: 1.800.775.0703 I © 2019 Kraus USA Inc. I REV.
Congratulations on the purchase of your new Kraus plumbing fixture! Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product: STOP DO NOT RETURN TO STORE Please contact our Customer Service Team 1-800-775-0703 / customerservice@kraususa.com Have the model number available and retain a copy of your receipt with purchase date for reference.
Prior to Installation: · Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement. · Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber’s putty, or silicone. · Flush angle stops to release any debris prior to installation.
Diagram and Parts List A. Aerator E B A F D C 4 B. C. D. E. Faucet Body Base Hot & Cold Waterlines Hex Wrench Set E1. 2.5mm E2. 4mm F.
Faucet Dimensions 7" (178mm) 4 1/8" (105mm) 12 1/4" (310.5mm) 27 3/8" (694.5mm) (186mm) 5 1/2" (141mm) 36Max 7 3/8" 25° 2-9/16-24UNEF-2B Installer Tip: Shut off main water supply before installing new faucet.
Step 1: Install base Insert base (C) into base ring (F) on sink or countertop with “FR↑NT” facing forward. Tighten screws on base (C) with 4mm hex wrench (E) until base is secure on base ring (F) on sink or countertop. C Half Moon Locking Nuts F Installer Tip: Rotate the two half-moon shaped locking nuts inward before inserting base (C) into base ring (F) on sink or countertop. Step 2: Install faucet B D Insert hot & cold waterlines (D), one by one, into large hole of base (C).
Step 3: Secure faucet Secure faucet body (B) by tightening the set screw with 2.5mm hex wrench (E). B E Step 4: Connect waterlines 1 Thread the nut (1) on the supply line onto the outlet of the water supply valve (2) and tighten with wrench. Do not overtighten.
Step 5. Flush faucet Remove aerator (A). Turn faucet on for 1 minute to flush any debris. Reconnect aerator (A). A A Trouble-Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: 8 PROBLEM CAUSE ACTION Water does not shut off completely Cartridge (5) may need to be adjusted or replaced. Remove index button (1A). Loosen set screw (1B) with 2.5mm hex wrench (12). Remove metal handle (2).
Replacement Parts Replacement Parts List 7 6 5 Finish/Color Part # 1. Handle Assembly CH, SFS* KP07100 2. Cartridge Cover CH, SFS* KP07101 3. Locking Nut KP07102 4. Cartridge KP07047 5. Seal Kit KP07103 6. Set Screw CH, SFS* KP07104 7. Aerator Assembly CH, SFS* KP07105 KP07108 8. Set Screw 9. Base Ring 4 8 3 2 9 1 CH, SFS* KP07106 10. Base KP07004 11. Hex Wrench Set KP07109 (2.
Codes/Standards Applicable: NSF/ANSI 372 UP C NSF/ANSI 61-9 UP C R C ASME A112.18.1 1.8GPM 6.8L/min maximum C R FAUCET WARRANTY Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus"). Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable.
Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.
IMPORTANT Register Your Kraus Product Activate Your Warranty Access Premium Customer Support Get Product Information REGISTER TODAY http://www.kraususa.com/registration R www.kraususa.
