I N S TA L L AT I O N MA N UA L Oletto™ Single Lever Bar/Prep Faucet KPF-2600 www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV.
Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at 800.775.0703 and one of our representatives will be happy to help. For more information about Kraus products, please visit: www.kraususa.
7/8” (22mm) 19.7 º 10 1/8” (257mm) 8 5/16” (21mm) ∅ 1 15/16” (∅ 50mm) Prior to Installation: ∅ 1 3/4” (∅ 45mm) • ∅ 1 15/16” (∅ 50mm) 1 3/8” (35mm) Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800775-0703 for a replacement • Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet.
Diagram and Parts List E A B D F C A. Aerator B. Faucet Body E1. 2.5mm C. Base E2. 4mm D. Hot & Cold Waterlines 3 E. Hex Wrench Set F.
Faucet Dimensions 12-1/4" (310.5 mm) 10˚ Ø1-3/4" (46mm) 4-1/4” (109.5mm) 4-1/4” (109.5mm) 9/16 - 24 UNEF9/16 - 24 UNEF 2” (51mm) 1/16” ~1-1/2” (1mm~38mm) 2” (51mm) 1/16” ~1-1/2” (1mm~38mm) Ø1-3/4" (46mm) Ø1-3/4” (46mm) Ø1-3/4” (46mm) 10˚ 7” (177.9mm) 12-1/4" (310.5 mm) 5-1/2" (140.2mm) 7-3/8” (187.6mm) 2-7/8” (72.1mm) 7” (177.9mm) 5-1/2" (140.2mm) 7-3/8” (187.6mm) 2-7/8” (72.
Step 1: Install base Insert base (C) into base ring (F) on sink or countertop with “FR↑NT” facing forward.
Step 3: Connect waterlines to main valve D D Cold Hot Thread hot & cold waterlines (D) onto angle stops. Tighten with adjustable wrench until snug. Turn on the angle stops and check for leaks (DO NOT TURN FAUCET ON) Installer Tip: Use two D wrenches when securing waterlines to angle stops to prevent kinking, as shown in picture C B Step 4: Flush faucet E C Remove aerator (A). Turn faucet on for 1 minute to flush any debris.
Replacement Part List 1. A Index Button B Set Screw 2. Metal Handle 8. 3. Cartridge Cover 4. Locking Nut 5. Cartridge 6. 6. Seal Kit 7. 7. Insert 8. Aerator 5 4 9 9. Set Screw 3 10. Base Ring 2 11. Base 1 12. Hex Wrench 2.5mm 13.
Hexagon Nut 9 11 12 13 Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE Water will not shut off completely Close 25˚ Open Left Hot Water Water Cold Water Cartridge (5) may need to be adjusted or replaced Remove index button (1A). Loosen set screw (1B) with 2.5mm hex wrench (12). Remove metal handle (2). Remove cartridge cover (3) by hand only.
Codes/Standards Applicable: GREEN LEAD FREE IA P NSF/ANSI Standard 61 certified by IAPMO NSF/ANSI Standard 372 certified by IAPMO MO Meets ASME A112.18.1M/A112.18.1 R& T 1.5GPM 5.7L/min maximum TM Water Efficiency HELP LINE Our customer service hours are Monday – Friday, 9am – 8pm EST. Be sure to visit our website at www.kraususa.com If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc.
www.kraususa.
R E G I S T E R Y O U R P R O D U C T T O D AY Receive Proof of Ownership Access Customer Care & Installation Help Get Exclusive Kraus Offers & Promotions Scan to Register Online or visit http://www.kraususa.com/registration We’re always looking for ways to improve. Please take a moment to share your experience. Visit http://www.kraususa.com/review to let us know what you think about your new Kraus product. Contact Us to Learn More 1.800.775.0703 / www.kraususa.com / customerservice@kraususa.
